mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 23:47:24 +00:00
5aeab3bf5e
J721e has two instances of Cadence USB3 controller. Add DT nodes for the same. USB0 is configured to device mode and USB1 is configured to host mode. For now only high speed mode is supported. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
116 lines
2 KiB
Text
116 lines
2 KiB
Text
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "k3-j721e-som-p0.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
stdout-path = "serial2:115200n8";
|
|
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
|
|
};
|
|
|
|
aliases {
|
|
remoteproc0 = &mcu_r5fss0_core0;
|
|
remoteproc1 = &mcu_r5fss0_core1;
|
|
remoteproc2 = &main_r5fss0_core0;
|
|
remoteproc3 = &main_r5fss0_core1;
|
|
remoteproc4 = &main_r5fss1_core0;
|
|
remoteproc5 = &main_r5fss1_core1;
|
|
remoteproc6 = &c66_0;
|
|
remoteproc7 = &c66_1;
|
|
remoteproc8 = &c71_0;
|
|
};
|
|
};
|
|
|
|
&wkup_uart0 {
|
|
/* Wakeup UART is used by System firmware */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart0 {
|
|
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
|
|
};
|
|
|
|
&main_uart3 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart5 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart6 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart7 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart8 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_uart9 {
|
|
/* UART not brought out */
|
|
status = "disabled";
|
|
};
|
|
|
|
&main_sdhci0 {
|
|
/* eMMC */
|
|
voltage-ranges = <1800 1800>;
|
|
non-removable;
|
|
ti,driver-strength-ohm = <50>;
|
|
};
|
|
|
|
&main_sdhci1 {
|
|
/* SD/MMC */
|
|
voltage-ranges = <1800 1800 3300 3300>;
|
|
ti,driver-strength-ohm = <50>;
|
|
};
|
|
|
|
&main_pmx0 {
|
|
main_usbss0_pins_default: main_usbss0_pins_default {
|
|
pinctrl-single,pins = <
|
|
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
|
|
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
|
|
>;
|
|
};
|
|
|
|
main_usbss1_pins_default: main_usbss1_pins_default {
|
|
pinctrl-single,pins = <
|
|
J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&usbss0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&main_usbss0_pins_default>;
|
|
ti,vbus-divider;
|
|
};
|
|
|
|
&usb0 {
|
|
dr_mode = "otg";
|
|
maximum-speed = "super-speed";
|
|
};
|
|
|
|
&usbss1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&main_usbss1_pins_default>;
|
|
ti,usb2-only;
|
|
};
|
|
|
|
&usb1 {
|
|
dr_mode = "host";
|
|
maximum-speed = "high-speed";
|
|
};
|