u-boot/cpu/mpc8xxx/ddr/options.c
Kumar Gala 58e5e9aff1 FSL DDR: Rewrite the FSL mpc8xxx DDR controller setup code.
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers.  (83xx, 85xx, 86xx).

The code is broken up into the following steps:
	GET_SPD
	COMPUTE_DIMM_PARMS
	COMPUTE_COMMON_PARMS
	GATHER_OPTS
	ASSIGN_ADDRESSES
	COMPUTE_REGS
	PROGRAM_REGS

This allows us to share more code an easily allow for board specific code
overrides.

Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 02:05:58 +02:00

197 lines
5 KiB
C

/*
* Copyright 2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <asm/fsl_ddr_sdram.h>
#include "ddr.h"
/* Board-specific functions defined in each board's ddr.c */
extern void fsl_ddr_board_options(memctl_options_t *popts,
unsigned int ctrl_num);
unsigned int populate_memctl_options(int all_DIMMs_registered,
memctl_options_t *popts,
unsigned int ctrl_num)
{
unsigned int i;
/* Chip select options. */
/* Pick chip-select local options. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
/* If not DDR2, odt_rd_cfg and odt_wr_cfg need to be 0. */
/* only for single CS? */
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 1;
popts->cs_local_opts[i].auto_precharge = 0;
}
/* Pick interleaving mode. */
/*
* 0 = no interleaving
* 1 = interleaving between 2 controllers
*/
popts->memctl_interleaving = 0;
/*
* 0 = cacheline
* 1 = page
* 2 = (logical) bank
* 3 = superbank (only if CS interleaving is enabled)
*/
popts->memctl_interleaving_mode = 0;
/*
* 0: cacheline: bit 30 of the 36-bit physical addr selects the memctl
* 1: page: bit to the left of the column bits selects the memctl
* 2: bank: bit to the left of the bank bits selects the memctl
* 3: superbank: bit to the left of the chip select selects the memctl
*
* NOTE: ba_intlv (rank interleaving) is independent of memory
* controller interleaving; it is only within a memory controller.
* Must use superbank interleaving if rank interleaving is used and
* memory controller interleaving is enabled.
*/
/*
* 0 = no
* 0x40 = CS0,CS1
* 0x20 = CS2,CS3
* 0x60 = CS0,CS1 + CS2,CS3
* 0x04 = CS0,CS1,CS2,CS3
*/
popts->ba_intlv_ctl = 0;
/* Memory Organization Parameters */
popts->registered_dimm_en = all_DIMMs_registered;
/* Operational Mode Paramters */
/* Pick ECC modes */
#ifdef CONFIG_DDR_ECC
popts->ECC_mode = 1; /* 0 = disabled, 1 = enabled */
#else
popts->ECC_mode = 0; /* 0 = disabled, 1 = enabled */
#endif
popts->ECC_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */
/*
* Choose DQS config
* 0 for DDR1
* 1 for DDR2
*/
#if defined(CONFIG_FSL_DDR1)
popts->DQS_config = 0;
#elif defined(CONFIG_FSL_DDR2)
popts->DQS_config = 1;
#else
#error "Fix DQS for DDR3"
#endif
/* Choose self-refresh during sleep. */
popts->self_refresh_in_sleep = 1;
/* Choose dynamic power management mode. */
popts->dynamic_power = 0;
/* 0 = 64-bit, 1 = 32-bit, 2 = 16-bit */
popts->data_bus_width = 0;
/* Choose burst length. */
popts->burst_length = 4; /* has to be 4 for DDR2 */
/* Global Timing Parameters. */
debug("mclk_ps = %u ps\n", get_memory_clk_period_ps());
/* Pick a caslat override. */
popts->cas_latency_override = 0;
popts->cas_latency_override_value = 3;
if (popts->cas_latency_override) {
debug("using caslat override value = %u\n",
popts->cas_latency_override_value);
}
/* Decide whether to use the computed derated latency */
popts->use_derated_caslat = 0;
/* Choose an additive latency. */
popts->additive_latency_override = 0;
popts->additive_latency_override_value = 3;
if (popts->additive_latency_override) {
debug("using additive latency override value = %u\n",
popts->additive_latency_override_value);
}
/*
* 2T_EN setting
*
* Factors to consider for 2T_EN:
* - number of DIMMs installed
* - number of components, number of active ranks
* - how much time you want to spend playing around
*/
popts->twoT_en = 1;
popts->threeT_en = 0;
/*
* BSTTOPRE precharge interval
*
* Set this to 0 for global auto precharge
*
* FIXME: Should this be configured in picoseconds?
* Why it should be in ps: better understanding of this
* relative to actual DRAM timing parameters such as tRAS.
* e.g. tRAS(min) = 40 ns
*/
popts->bstopre = 0x100;
/* Minimum CKE pulse width -- tCKE(MIN) */
popts->tCKE_clock_pulse_width_ps
= mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR);
/*
* Window for four activates -- tFAW
*
* FIXME: UM: applies only to DDR2/DDR3 with eight logical banks only
* FIXME: varies depending upon number of column addresses or data
* FIXME: width, was considering looking at pdimm->primary_sdram_width
*/
#if defined(CONFIG_FSL_DDR1)
popts->tFAW_window_four_activates_ps = mclk_to_picos(1);
#elif defined(CONFIG_FSL_DDR2)
/*
* x4/x8; some datasheets have 35000
* x16 wide columns only? Use 50000?
*/
popts->tFAW_window_four_activates_ps = 37500;
#elif defined(CONFIG_FSL_DDR3)
#error "FIXME determine four activates for DDR3"
#endif
/* ODT should only be used for DDR2 */
/* FIXME? */
/*
* Interleaving checks.
*
* If memory controller interleaving is enabled, then the data
* bus widths must be programmed identically for the 2 memory
* controllers.
*/
fsl_ddr_board_options(popts, ctrl_num);
return 0;
}