mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
efeff5382b
- Moved some common code to nestal/common/nm_bsp.c. - Added support for the vxWorks EDR. - Enable trace for Lauterbach, if present. - Added support for POST. - Stylistic cleanups (multi-line comments/ enforce 80 colomn width) Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
171 lines
4.3 KiB
Text
171 lines
4.3 KiB
Text
HCU5 configuration details and startup sequence
|
||
|
||
(C) Copyright 2007 Netstal Maschinen AG
|
||
Niklaus Giger (Niklaus.Giger@netstal.com)
|
||
|
||
TODO:
|
||
-----
|
||
- Fix error: Waiting for PHY auto negotiation to complete..... TIMEOUT !
|
||
- Does not occur if both EMAC are connected
|
||
- Fix RTS/CTS problem (HW?)
|
||
CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after
|
||
Switching to interrupt driven serial input mode
|
||
|
||
Caveats:
|
||
--------
|
||
Errata CHIP_8: Incorrect Write to DDR SDRAM. (was not applied to sequoia.c)
|
||
see hcu5.c.
|
||
|
||
|
||
Memory Bank 0 -- Flash chip
|
||
---------------------------
|
||
|
||
0xfff00000 - 0xffffffff
|
||
|
||
The flash chip is really only 512Kbytes, but the high address bit of
|
||
the 1Meg region is ignored, so the flash is replicated through the
|
||
region. Thus, this is consistent with a flash base address 0xfff80000.
|
||
|
||
The placement at the end is to be consistent with reset behavior,
|
||
where the processor itself initially uses this bus to load the branch
|
||
vector and start running.
|
||
|
||
On-Chip Memory
|
||
--------------
|
||
|
||
0xe0010000- 0xe0013fff CFG_OCM_BASE
|
||
The 440EPx includes a 16K on-chip memory that can be placed however
|
||
software chooses.
|
||
|
||
Internal Peripherals
|
||
--------------------
|
||
|
||
0xef600300 - 0xef6008ff
|
||
|
||
These are scattered various peripherals internal to the PPC440EPX
|
||
chip.
|
||
|
||
Chip-Select 2: Flash Memory
|
||
---------------------------
|
||
|
||
Not used
|
||
|
||
Chip-Select 3: CAN Interface
|
||
----------------------------
|
||
0xc800000: 2 Intel 82527 CAN-Controller
|
||
|
||
|
||
Chip-Select 4: IMC-bus standard
|
||
-------------------------------
|
||
|
||
0xcc00000: Netstal specific IO-Bus
|
||
|
||
|
||
Chip-Select 5: IMC-bus fast (inactive)
|
||
--------------------------------------
|
||
|
||
0xce00000: Netstal specific IO-Bus (fast, but not yet used)
|
||
|
||
|
||
Memory Bank 1 -- DDR2
|
||
-------------------------------------
|
||
|
||
0x00000000 - 0xfffffff # Default 256 MB
|
||
|
||
PCI ??
|
||
|
||
USB ??
|
||
Only USB_STORAGE is enabled to load vxWorks
|
||
from a memory stick.
|
||
|
||
System-LEDs ??? (Analog zu HCU4 ???)
|
||
|
||
Startup sequence
|
||
----------------
|
||
|
||
(cpu/ppc4xx/resetvec.S)
|
||
depending on configs option
|
||
call _start_440 _start_pci oder _start
|
||
|
||
(cpu/ppc4xx/start.S)
|
||
|
||
_start_440:
|
||
initialize register like
|
||
CCR0
|
||
debug
|
||
setup interrupt vectors
|
||
configure cache regions
|
||
clear and setup TLB
|
||
enable internal RAM
|
||
jump start_ram
|
||
which in turn will jump to start
|
||
_start:
|
||
Clear and set up some registers.
|
||
Debug setup
|
||
Setup the internal SRAM
|
||
Setup the stack in internal SRAM
|
||
setup stack pointer (r1)
|
||
setup GOT
|
||
call cpu_init_f /* run low-level CPU init code (from Flash) */
|
||
|
||
call cpu_init_f
|
||
board_init_f: (lib_ppc\board.c)
|
||
init_sequence defines a list of function to be called
|
||
board_early_init_f: (board/netstal/hcu5/hcu5.c)
|
||
We are using Bootstrap-Option A
|
||
if CPR0_ICFG_RLI_MASK == 0 then set some registers and reboot
|
||
Setup the GPIO pins
|
||
Setup the interrupt controller polarities, triggers, etc.
|
||
Ethernet, PCI, USB enable
|
||
setup BOOT FLASH (Chip timing)
|
||
init_baudrate,
|
||
serial_init
|
||
checkcpu
|
||
misc_init_f #ifdef
|
||
init_func_i2c #ifdef
|
||
post_init_f #ifdef
|
||
init_func_ram -> calls init_dram board/netstal/hcu5/sdram.c
|
||
(EYE function removed!!)
|
||
test_dram call
|
||
|
||
* Reserve memory at end of RAM for (top down in that order):
|
||
* - kernel log buffer
|
||
* - protected RAM
|
||
* - LCD framebuffer
|
||
* - monitor code
|
||
* - board info struct
|
||
Save local variables to board info struct
|
||
call relocate_code() does not return
|
||
relocate_code: (cpu/ppc4xx/start.S)
|
||
-------------------------------------------------------
|
||
From now on our copy is in RAM and we will run from there,
|
||
starting with board_init_r
|
||
-------------------------------------------------------
|
||
board_init_r: (lib_ppc\board.c)
|
||
setup bd function pointers
|
||
trap_init
|
||
flash_init: (board/netstal/hcu5/flash.c)
|
||
/* setup for u-boot erase, update */
|
||
setup bd flash info
|
||
cpu_init_r: (cpu/ppc4xx/cpu_init.c)
|
||
peripheral chip select in using defines like
|
||
CFG_EBC_PB0A, CFG_EBC_PB0C from hcu5.h
|
||
mem_malloc_init
|
||
malloc_bin_reloc
|
||
spi_init (r or f)??? (CFG_ENV_IS_IN_EEPROM)
|
||
env_relocated
|
||
misc_init_r(bd): (board/netstal/hcu5.c)
|
||
ethaddr mit serial number erg<72>nzen
|
||
Then we will somehow go into the command loop
|
||
|
||
Most of the HW specific code for the HCU5 may be found in
|
||
include/configs/hcu5.h
|
||
board/netstal/hcu5/*
|
||
cpu/ppc4xx/*
|
||
lib_ppc/*
|
||
include/ppc440.h
|
||
|
||
Drivers for serial etc are found under drivers/
|
||
|
||
Don't ask question if you did not look at the README !!
|
||
Most CFG_* and CONFIG_* switches are mentioned/explained there.
|