mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-03 18:10:13 +00:00
8974ff1a60
Some board like imx8mm-evkb, IO voltage switch from 3.3v to 1.8v need around 18ms, common code only delay 10ms, so need to delay extra 8ms. Otherwise voltage switch will timeout when wait for data0 line. This IO voltage switch time depends on board design, depend on the PMIC and capacitance. imx8mm-evkb board use PCA9450(PMIC) and 10uF capacitance. Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
253 lines
3.3 KiB
Text
253 lines
3.3 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2019 NXP
|
|
*/
|
|
|
|
/ {
|
|
binman: binman {
|
|
multiple-images;
|
|
};
|
|
|
|
wdt-reboot {
|
|
compatible = "wdt-reboot";
|
|
wdt = <&wdog1>;
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
firmware {
|
|
optee {
|
|
compatible = "linaro,optee-tz";
|
|
method = "smc";
|
|
};
|
|
};
|
|
};
|
|
|
|
&{/soc@0} {
|
|
u-boot,dm-pre-reloc;
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&clk {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
/delete-property/ assigned-clocks;
|
|
/delete-property/ assigned-clock-parents;
|
|
/delete-property/ assigned-clock-rates;
|
|
};
|
|
|
|
&osc_24m {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&aips1 {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&aips2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&aips3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&iomuxc {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
®_usdhc2_vmmc {
|
|
u-boot,off-on-delay-us = <20000>;
|
|
};
|
|
|
|
&pinctrl_reg_usdhc2_vmmc {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2_gpio {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio4 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio5 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc2 {
|
|
u-boot,dm-spl;
|
|
sd-uhs-sdr104;
|
|
sd-uhs-ddr50;
|
|
fsl,signal-voltage-switch-extra-delay-ms = <8>;
|
|
};
|
|
|
|
&usdhc3 {
|
|
u-boot,dm-spl;
|
|
mmc-hs400-1_8v;
|
|
mmc-hs400-enhanced-strobe;
|
|
};
|
|
|
|
&i2c1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&{/soc@0/bus@30800000/i2c@30a20000/pca9450@25} {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&{/soc@0/bus@30800000/i2c@30a20000/pca9450@25/regulators} {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_i2c1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_pmic {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&fec1 {
|
|
phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&wdog1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&binman {
|
|
u-boot-spl-ddr {
|
|
filename = "u-boot-spl-ddr.bin";
|
|
pad-byte = <0xff>;
|
|
align-size = <4>;
|
|
align = <4>;
|
|
|
|
u-boot-spl {
|
|
align-end = <4>;
|
|
};
|
|
|
|
blob_1: blob-ext@1 {
|
|
filename = "lpddr4_pmu_train_1d_imem.bin";
|
|
size = <0x8000>;
|
|
};
|
|
|
|
blob_2: blob-ext@2 {
|
|
filename = "lpddr4_pmu_train_1d_dmem.bin";
|
|
size = <0x4000>;
|
|
};
|
|
|
|
blob_3: blob-ext@3 {
|
|
filename = "lpddr4_pmu_train_2d_imem.bin";
|
|
size = <0x8000>;
|
|
};
|
|
|
|
blob_4: blob-ext@4 {
|
|
filename = "lpddr4_pmu_train_2d_dmem.bin";
|
|
size = <0x4000>;
|
|
};
|
|
};
|
|
|
|
|
|
flash {
|
|
mkimage {
|
|
args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";
|
|
|
|
blob {
|
|
filename = "u-boot-spl-ddr.bin";
|
|
};
|
|
};
|
|
};
|
|
|
|
itb {
|
|
filename = "u-boot.itb";
|
|
|
|
fit {
|
|
description = "Configuration to load ATF before U-Boot";
|
|
#address-cells = <1>;
|
|
fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
|
|
|
|
images {
|
|
uboot {
|
|
description = "U-Boot (64-bit)";
|
|
type = "standalone";
|
|
arch = "arm64";
|
|
compression = "none";
|
|
load = <CONFIG_SYS_TEXT_BASE>;
|
|
|
|
uboot_blob: blob-ext {
|
|
filename = "u-boot-nodtb.bin";
|
|
};
|
|
};
|
|
|
|
atf {
|
|
description = "ARM Trusted Firmware";
|
|
type = "firmware";
|
|
arch = "arm64";
|
|
compression = "none";
|
|
load = <0x920000>;
|
|
entry = <0x920000>;
|
|
|
|
atf_blob: blob-ext {
|
|
filename = "bl31.bin";
|
|
};
|
|
};
|
|
|
|
fdt {
|
|
description = "NAME";
|
|
type = "flat_dt";
|
|
compression = "none";
|
|
|
|
uboot_fdt_blob: blob-ext {
|
|
filename = "u-boot.dtb";
|
|
};
|
|
};
|
|
};
|
|
|
|
configurations {
|
|
default = "conf";
|
|
|
|
conf {
|
|
description = "NAME";
|
|
firmware = "uboot";
|
|
loadables = "atf";
|
|
fdt = "fdt";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|