mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-04 18:41:03 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
131 lines
4.5 KiB
Text
131 lines
4.5 KiB
Text
This directory contains board specific code for a generic MPC860T based
|
|
embedded computer, called 'GEN860T'. The design is generic in the sense that
|
|
common, readily available components are used and that the architecture of the
|
|
system is relatively straightforward:
|
|
|
|
One eight bit wide boot (FLASH) memory
|
|
32 bit main memory using SDRAM
|
|
DOC 2000+
|
|
Ethernet PHY
|
|
Some I2C peripheral devices: Atmel AT24C256 EEPROM, Maxim DS1337 RTC.
|
|
Some other miscellaneous peripherals
|
|
|
|
NOTE: There are references to a XIlinx FPGA and Mil-Std 1553 databus in this
|
|
port. I guess the computer is not as generic as I first said 8) However,
|
|
these extras can be safely ignored.
|
|
|
|
Given the GEN860T files, it should be pretty easy to reverse engineer the
|
|
hardware configuration, if that's useful to you. Hopefully, this code will
|
|
be useful to someone as a basis for a port to a new system or as a head start
|
|
on a custom design. If you end up using any of this, I would appreciate
|
|
hearing from you, especially if you discover bugs or find ways to improve the
|
|
quality of this U-Boot port.
|
|
|
|
Here are the salient features of the system:
|
|
Clock : 33.3 Mhz oscillator
|
|
Processor core frequency : 66.6 Mhz if in 1:2:1 mode; can also run 1:1
|
|
Bus frequency : 33.3 Mhz
|
|
|
|
Main memory:
|
|
Type : SDRAM
|
|
Width : 32 bits
|
|
Size : 64 mibibytes
|
|
Chip : Two Micron MT48LC16M16A2TG-7E
|
|
CS : MPC860T CS1*/UPMA
|
|
UPMA CONNECTIONS:
|
|
SDRAM A10 : GPLA0*
|
|
SDRAM CAS* : GPLA2*
|
|
SDRAM WE* : GPLA3*
|
|
SDRAM RAS* : GPLA4*
|
|
|
|
Boot memory:
|
|
Type : FLASH
|
|
Width : 8 bits
|
|
Size : 16 mibibytes
|
|
Chip : One Intel 28F128J3A (StrataFlash)
|
|
CS : MPC860T CS0*/GPCM (this is the "boot" chip select)
|
|
|
|
EEPROM memory:
|
|
Type : Serial I2C EEPROM
|
|
Width : 8 bits
|
|
Size : 32 kibibytes
|
|
Chip : One Atmel AT25C256
|
|
CS : 0x50 (external I2C address pins on device are tied to GND)
|
|
|
|
Filesystem memory:
|
|
Type : NAND FLASH (Toshiba)
|
|
Width : 8 bits (i.e. interface to DOC is 8 bits)
|
|
Size : 32 mibibytes
|
|
Chip : One DiskOnCHip Millenium Plus (DOC 2000+)
|
|
CS : MPC860T CS2*/GPCM
|
|
|
|
Network support:
|
|
MAC : MPC86OT FEC (Fast Ethernet Controller)
|
|
PHY : Intel LXT971A
|
|
MII Addr: 0x0 (hardwired on the board)
|
|
MII IRQ :
|
|
|
|
Console:
|
|
RS-232 on SMC1 (Maxim MAX3232 LVCMOS-RS232 level shifter)
|
|
|
|
Real Time Clock:
|
|
Type : Low power, I2C interface
|
|
Chip : Maxim DS1337
|
|
CS : Address 0x68 on I2C bus
|
|
|
|
The MPC860T's internal RTC has a defect in Mask rev D that increases
|
|
the current drain on the KAPWR line to 10 mA. Since this is an
|
|
unreasonable amount of current draw for a RTC, and Motorola does not
|
|
plan to fix this in future mask revisions, a serial (I2C) RTC that
|
|
works has been included instead. NOTE that the DS1337 can be
|
|
configured to output a 32768 Hz clock while the main power is on.
|
|
This clock output has been routed to the MPC860T's EXTAL pin to allow
|
|
the internal RTC to be used. NOTE also that due to yet another
|
|
defect in the rev D mask, the RTC does not operate reliably when the
|
|
internal RTC divisor is set to use a 32768 Hz reference. So just use
|
|
the I2C RTC.
|
|
|
|
Miscellaneous:
|
|
Xilinx Virtex FPGA on CS3*/GPCM.
|
|
Virtex FPGA slave SelectMap interface on cs4*/UPMB.
|
|
Mil-Std 1553 databus interface on CS5*/GPCM.
|
|
Audio sounder (beeper) with digital volume control connected to SPKROUT.
|
|
|
|
SC variant:
|
|
A reduced-feature version of the GEN860T port is also supported: GEN860T_SC.
|
|
The 'SC' variant only provides support for the Virtex FPGA, SDRAM main
|
|
memory, EEPROM and flash memory. The system clock frequency is reduced
|
|
to 24 MHz.
|
|
|
|
Issues:
|
|
The DOC 2000+ returns 0x40 as its device ID when probed using the method
|
|
desxribed in the DOC datasheet. Unfortunately, the U-Boot DOC driver
|
|
does not recognize this device. As of this writing, it seems that MTD
|
|
does not support the DOC 2000+ either.
|
|
|
|
Status:
|
|
Everything appears to work except DOC support. As of this writing,
|
|
David Woodhouse has stated on the MTD mailing list that he has no
|
|
knowledge of the DOC Millineum Plus and therfore there is no support
|
|
in MTD for this device. I wish I had known this sooner :(
|
|
|
|
The GEN860T board specific files and configuration is based on the work
|
|
of others who have contributed to U-Boot. The copyright and license notices
|
|
of these authors have been retained wherever their code has been reused.
|
|
All new code to support the GEN860T board is:
|
|
|
|
(C) Copyright 2001-2003
|
|
Keith Outwater (keith_outwater@mvis.com)
|
|
|
|
and the following license applies:
|
|
|
|
SPDX-License-Identifier: GPL-2.0+
|
|
|
|
Thanks to Wolfgang Denk for a great software package and to everyone
|
|
who contributed to its development.
|
|
|
|
Keith Outwater
|
|
Sr. Staff Engineer
|
|
Microvision, Inc.
|
|
<keith_outwater@mvis.com>
|
|
<outwater@eskimo.com>
|