u-boot/include/configs/imx8ulp_evk.h
Tom Rini 5523afbe4a Convert CONFIG_BOARD_EARLY_INIT_F et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F
   CONFIG_BOARD_LATE_INIT
   CONFIG_DISPLAY_BOARDINFO
   CONFIG_DISPLAY_BOARDINFO_LATE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-05 11:26:29 -04:00

93 lines
2.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2020 NXP
*/
#ifndef __IMX8ULP_EVK_H
#define __IMX8ULP_EVK_H
#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN (SZ_64M)
#define CONFIG_SPL_MAX_SIZE (148 * 1024)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SYS_UBOOT_BASE (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK 0x22050000
#define CONFIG_SPL_BSS_START_ADDR 0x22048000
#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x22040000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x8000 /* 32 KB */
#define CONFIG_MALLOC_F_ADDR 0x22040000
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */
#endif
#define CONFIG_REMAKE_ELF
/* ENET Config */
#if defined(CONFIG_FEC_MXC)
#define CONFIG_ETHPRIME "FEC"
#define PHY_ANEG_TIMEOUT 20000
#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_FEC_MXC_PHYADDR 1
#define IMX_FEC_BASE 0x29950000
#endif
#ifdef CONFIG_DISTRO_DEFAULTS
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0)
#include <config_distro_bootcmd.h>
#else
#define BOOTENV
#endif
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
BOOTENV \
"scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"image=Image\0" \
"console=ttyLP1,115200 earlycon\0" \
"fdt_addr_r=0x83000000\0" \
"boot_fit=no\0" \
"fdtfile=imx8ulp-evk.dtb\0" \
"initrd_addr=0x83800000\0" \
"bootm_size=0x10000000\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_ENV_OVERWRITE
#define CONFIG_MMCROOT "/dev/mmcblk2p2"
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define PHYS_SDRAM 0x80000000
#define PHYS_SDRAM_SIZE 0x80000000 /* 2GB DDR */
/* Monitor Command Prompt */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Using ULP WDOG for reset */
#define WDOG_BASE_ADDR WDG3_RBASE
#endif