mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-20 18:23:08 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
101 lines
2.5 KiB
C
101 lines
2.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <init.h>
|
|
#include <malloc.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/immap.h>
|
|
#include <linux/delay.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int checkboard (void) {
|
|
ulong val;
|
|
uchar val8;
|
|
|
|
puts ("Board: ");
|
|
puts("Freescale M5249EVB");
|
|
val8 = ((uchar)~((uchar)mbar2_readLong(MCFSIM_GPIO1_READ) >> 4)) & 0xf;
|
|
printf(" (Switch=%1X)\n", val8);
|
|
|
|
/*
|
|
* Set LED on
|
|
*/
|
|
val = mbar2_readLong(MCFSIM_GPIO1_OUT) & ~CONFIG_SYS_GPIO1_LED;
|
|
mbar2_writeLong(MCFSIM_GPIO1_OUT, val); /* Set LED on */
|
|
|
|
return 0;
|
|
};
|
|
|
|
|
|
int dram_init(void)
|
|
{
|
|
unsigned long junk = 0xa5a59696;
|
|
|
|
/*
|
|
* Note:
|
|
* RC = ([(RefreshTime/#rows) / (1/BusClk)] / 16) - 1
|
|
*/
|
|
|
|
#ifdef CONFIG_SYS_FAST_CLK
|
|
/*
|
|
* Busclk=70MHz, RefreshTime=64ms, #rows=4096 (4K)
|
|
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=39
|
|
*/
|
|
mbar_writeShort(MCFSIM_DCR, 0x8239);
|
|
#elif CONFIG_SYS_PLL_BYPASS
|
|
/*
|
|
* Busclk=5.6448MHz, RefreshTime=64ms, #rows=8192 (8K)
|
|
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=02
|
|
*/
|
|
mbar_writeShort(MCFSIM_DCR, 0x8202);
|
|
#else
|
|
/*
|
|
* Busclk=36MHz, RefreshTime=64ms, #rows=4096 (4K)
|
|
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=22 (562 bus clock cycles)
|
|
*/
|
|
mbar_writeShort(MCFSIM_DCR, 0x8222);
|
|
#endif
|
|
|
|
/*
|
|
* SDRAM starts at 0x0000_0000, CASL=10, CBM=010, PS=10 (16bit port),
|
|
* PM=1 (continuous page mode)
|
|
*/
|
|
|
|
/* RE=0 (keep auto-refresh disabled while setting up registers) */
|
|
mbar_writeLong(MCFSIM_DACR0, 0x00003324);
|
|
|
|
/* BAM=007c (bits 22,21 are bank selects; 256kB blocks) */
|
|
mbar_writeLong(MCFSIM_DMR0, 0x01fc0001);
|
|
|
|
/** Precharge sequence **/
|
|
mbar_writeLong(MCFSIM_DACR0, 0x0000332c); /* Set DACR0[IP] (bit 3) */
|
|
*((volatile unsigned long *) 0x00) = junk; /* write to a memory location to init. precharge */
|
|
udelay(0x10); /* Allow several Precharge cycles */
|
|
|
|
/** Refresh Sequence **/
|
|
mbar_writeLong(MCFSIM_DACR0, 0x0000b324); /* Enable the refresh bit, DACR0[RE] (bit 15) */
|
|
udelay(0x7d0); /* Allow gobs of refresh cycles */
|
|
|
|
/** Mode Register initialization **/
|
|
mbar_writeLong(MCFSIM_DACR0, 0x0000b364); /* Enable DACR0[IMRS] (bit 6); RE remains enabled */
|
|
*((volatile unsigned long *) 0x800) = junk; /* Access RAM to initialize the mode register */
|
|
|
|
gd->ram_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
|
|
|
|
return 0;
|
|
};
|
|
|
|
|
|
int testdram(void)
|
|
{
|
|
/* TODO: XXX XXX XXX */
|
|
printf ("DRAM test not implemented!\n");
|
|
|
|
return (0);
|
|
}
|