u-boot/arch/arm/mach-rockchip/Makefile
Jagan Teki e230c579a3 rockchip: Separate the reset cause from display cpuinfo
reset cause is a generic functionality based on the soc
cru registers in rockchip. This can be used for printing
the cause of reset in cpuinfo or some other place where
reset cause is needed. 

Other than cpuinfo, reset cause can also be using during
bootcount for checking the specific reset cause and glow
the led based on the reset cause.

So, let's separate the reset cause code from cpuinfo, and
add a check to build it for rk3399, rk3288 since these two
soc are supporting reset cause as of now.

Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00

52 lines
1.9 KiB
Makefile

# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (c) 2014 Google, Inc
# Copyright (c) 2019 Rockchip Electronics Co., Ltd.
# We don't want the bootrom-helper present in a full U-Boot build, as
# this may have entered from ATF with the stack-pointer pointing to
# inaccessible/protected memory (and the bootrom-helper assumes that
# the stack-pointer is valid before switching to the U-Boot stack).
obj-spl-$(CONFIG_ROCKCHIP_BROM_HELPER) += bootrom.o
obj-spl-$(CONFIG_SPL_ROCKCHIP_COMMON_BOARD) += spl.o spl-boot-order.o
obj-tpl-$(CONFIG_ROCKCHIP_BROM_HELPER) += bootrom.o
obj-tpl-$(CONFIG_TPL_ROCKCHIP_COMMON_BOARD) += tpl.o
obj-tpl-$(CONFIG_ROCKCHIP_PX30) += px30-board-tpl.o
obj-spl-$(CONFIG_ROCKCHIP_RK3036) += rk3036-board-spl.o
ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),)
# Always include boot_mode.o, as we bypass it (i.e. turn it off)
# inside of boot_mode.c when CONFIG_BOOT_MODE_REG is 0. This way,
# we can have the preprocessor correctly recognise both 0x0 and 0
# meaning "turn it off".
obj-y += boot_mode.o
obj-$(CONFIG_ROCKCHIP_COMMON_BOARD) += board.o
obj-$(CONFIG_MISC_INIT_R) += misc.o
endif
ifeq ($(CONFIG_TPL_BUILD),)
obj-$(CONFIG_DISPLAY_CPUINFO) += cpu-info.o
endif
obj-$(CONFIG_$(SPL_TPL_)RAM) += sdram.o
obj-$(CONFIG_ROCKCHIP_PX30) += px30/
obj-$(CONFIG_ROCKCHIP_RK3036) += rk3036/
obj-$(CONFIG_ROCKCHIP_RK3128) += rk3128/
obj-$(CONFIG_ROCKCHIP_RK3188) += rk3188/
obj-$(CONFIG_ROCKCHIP_RK322X) += rk322x/
obj-$(CONFIG_ROCKCHIP_RK3288) += rk3288/
obj-$(CONFIG_ROCKCHIP_RK3308) += rk3308/
obj-$(CONFIG_ROCKCHIP_RK3328) += rk3328/
obj-$(CONFIG_ROCKCHIP_RK3368) += rk3368/
obj-$(CONFIG_ROCKCHIP_RK3399) += rk3399/
obj-$(CONFIG_ROCKCHIP_RV1108) += rv1108/
# Clear out SPL objects, in case this is a TPL build
obj-spl-$(CONFIG_TPL_BUILD) =
# Now add SPL/TPL objects back into the main build
obj-$(CONFIG_SPL_BUILD) += $(obj-spl-y)
obj-$(CONFIG_TPL_BUILD) += $(obj-tpl-y)