mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
7dd97af523
The following config symbols are only defined once and never referenced anywhere else: CONFIG_CYRUS CONFIG_IDS8313 CONFIG_MPC8308_P1M CONFIG_MPC8308RDB CONFIG_MPC8349EMDS CONFIG_MPC8349ITXGP CONFIG_SBC8349 CONFIG_SBC8548 CONFIG_SBC8641D CONFIG_TQM834X CONFIG_VE8313 CONFIG_XPEDITE5140 CONFIG_XPEDITE5200 CONFIG_XPEDITE550X Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Mario Six <mario.six@gdsys.cc>
186 lines
5.6 KiB
Text
186 lines
5.6 KiB
Text
Freescale MPC8349E-mITX and MPC8349E-mITX-GP Boards
|
|
---------------------------------------------------
|
|
|
|
1. Board Description
|
|
|
|
The MPC8349E-mITX and MPC8349E-mITX-GP are reference boards featuring
|
|
the Freescale MPC8349E processor in a Mini-ITX form factor.
|
|
|
|
The MPC8349E-mITX-GP is an MPC8349E-mITX with the following differences:
|
|
|
|
A) One 8MB on-board flash EEPROM chip, instead of two.
|
|
B) No SATA controller
|
|
C) No Compact Flash slot
|
|
D) No Mini-PCI slot
|
|
E) No Vitesse 7385 5-port Ethernet switch
|
|
F) No 4-port USB Type-A interface
|
|
|
|
2. Board Switches and Jumpers
|
|
|
|
2.0 Descriptions for all of the board jumpers can be found in the User
|
|
Guide. Of particular interest to U-Boot developers is jumper J22:
|
|
|
|
Pos. Name Default Description
|
|
-----------------------------------------------------------------------
|
|
A LGPL0 ON (0) HRCW source, bit 0
|
|
B LGPL1 ON (0) HRCW source, bit 1
|
|
C LGPL3 ON (0) HRCW source, bit 2
|
|
D LGPL5 OFF (1) PCI_SYNC_OUT frequency
|
|
E BOOT1 ON (0) Flash EEPROM boot device
|
|
F PCI_M66EN ON (0) PCI 66MHz enable
|
|
G I2C-WP ON (0) I2C EEPROM write protection
|
|
H F_WP OFF (1) Flash EEPROM write protection
|
|
|
|
Jumper J22.E is only for the ITX, and it decides the configuration
|
|
of the flash chips. If J22.E is ON (i.e. jumpered), then flash chip
|
|
U4 is located at address FE000000 and flash chip U7 is at FE800000.
|
|
If J22.E is OFF, then U7 is at FE000000 and U4 is at FE800000.
|
|
|
|
For U-Boot development, J22.E can be used to switch back-and-forth
|
|
between two U-Boot images.
|
|
|
|
3. Memory Map
|
|
|
|
3.1. The memory map should look pretty much like this:
|
|
|
|
0x0000_0000 - 0x0FFF_FFFF DDR SDRAM (256 MB)
|
|
0x8000_0000 - 0x9FFF_FFFF PCI1 memory space (512 MB)
|
|
0xA000_0000 - 0xBFFF_FFFF PCI2 memory space (512 MB)
|
|
0xE000_0000 - 0xEFFF_FFFF IMMR (1 MB)
|
|
0xE200_0000 - 0xE2FF_FFFF PCI1 I/O space (16 MB)
|
|
0xE300_0000 - 0xE3FF_FFFF PCI2 I/O space (16 MB)
|
|
0xF000_0000 - 0xF000_FFFF Compact Flash (ITX only)
|
|
0xF001_0000 - 0xF001_FFFF Local bus expansion slot
|
|
0xF800_0000 - 0xF801_FFFF Vitesse 7385 Parallel Interface (ITX only)
|
|
0xFE00_0000 - 0xFE7F_FFFF First 8MB bank of Flash memory
|
|
0xFE80_0000 - 0xFEFF_FFFF Second 8MB bank of Flash memory (ITX only)
|
|
|
|
3.2 Flash EEPROM layout.
|
|
|
|
On the ITX, jumper J22.E is used to determine which flash chips are
|
|
at which address. When J22.E is switched, addresses from FE000000
|
|
to FE7FFFFF are swapped with addresses from FE800000 to FEFFFFFF.
|
|
|
|
On the ITX, at the normal boot address (aka HIGHBOOT):
|
|
|
|
FE00_0000 HRCW
|
|
FE70_0000 Alternative U-Boot image
|
|
FE80_0000 Alternative HRCW
|
|
FEF0_0000 U-Boot image
|
|
FEFF_FFFF End of flash
|
|
|
|
On the ITX, at the low boot address (LOWBOOT)
|
|
|
|
FE00_0000 HRCW and U-Boot image
|
|
FE04_0000 U-Boot environment variables
|
|
FE80_0000 Alternative HRCW and U-Boot image
|
|
FEFF_FFFF End of flash
|
|
|
|
On the ITX-GP, the only option is LOWBOOT and there is only one chip
|
|
|
|
FE00_0000 HRCW and U-Boot image
|
|
FE04_0000 U-Boot environment variables
|
|
F7FF_FFFF End of flash
|
|
|
|
4. Definitions
|
|
|
|
4.1 Explanation of NEW definitions in:
|
|
|
|
include/configs/MPC8349ITX.h
|
|
|
|
CONFIG_MPC83xx MPC83xx family
|
|
CONFIG_MPC8349 MPC8349 specific
|
|
CONFIG_MPC8349ITX MPC8349E-mITX
|
|
|
|
5. Compilation
|
|
|
|
Assuming you're using BASH shell:
|
|
|
|
export CROSS_COMPILE=your-cross-compile-prefix
|
|
cd u-boot
|
|
make distclean
|
|
|
|
make MPC8349ITX_config
|
|
or:
|
|
make MPC8349ITXGP_config
|
|
or:
|
|
make MPC8349ITX_LOWBOOT_config
|
|
|
|
make
|
|
|
|
6. Downloading and Flashing Images
|
|
|
|
6.1 Download via tftp:
|
|
|
|
tftp $loadaddr <uboot>
|
|
|
|
where "<uboot>" is the path and filename, on the TFTP server, of
|
|
the U-Boot image.
|
|
|
|
6.1 Reflash U-Boot Image using U-Boot
|
|
|
|
setenv uboot <uboot>
|
|
run tftpflash
|
|
|
|
where "<uboot>" is the path and filename, on the TFTP server, of
|
|
the U-Boot image.
|
|
|
|
6.2 Using the HRCW to switch between two different U-Boot images on the ITX
|
|
|
|
Because the ITX has 16MB of flash, it is possible to keep two U-Boot
|
|
images in flash, and use the HRCW to specify which one is to be used
|
|
when the board boots. This trick is especially effective with a
|
|
hardware debugger that can override the HRCW, such as the BDI-2000.
|
|
|
|
When the BMS bit in the HRCW is 0, the ITX will boot the U-Boot image
|
|
at address FE000000. When the BMS bit is 1, the ITX will boot the
|
|
image at address FEF00000.
|
|
|
|
Therefore, just put a U-Boot image at both FE000000 and FEF00000 and
|
|
change the BMS bit whenever you want to boot the other image.
|
|
|
|
Step-by-step instructions:
|
|
|
|
1) Build an ITX image to be loaded at FEF00000
|
|
|
|
make distclean
|
|
make MPC8349ITX_config
|
|
make
|
|
|
|
2) Take the u-boot.bin image and flash it at FEF00000.
|
|
|
|
tftp $loadaddr u-boot.bin
|
|
protect off all
|
|
erase FEF00000 +$filesize
|
|
cp.b $loadaddr FEF00000 $filesize
|
|
|
|
3) Build an ITX image to be loaded at FE000000
|
|
|
|
make distclean
|
|
make MPC8349ITX_LOWBOOT_config
|
|
make
|
|
|
|
4) Take the u-boot.bin image and flash it at FE000000.
|
|
|
|
tftp $loadaddr u-boot.bin
|
|
protect off FE000000 +$filesize
|
|
erase FE000000 +$filesize
|
|
cp.b $loadaddr FE000000 $filesize
|
|
|
|
The HRCW in flash is currently set to boot the image at FE000000.
|
|
|
|
If you have a hardware debugger, configure it to set the HRCW to
|
|
B460A000 04040000 if you want to boot the image at FEF00000, or set
|
|
it to B060A000 04040000 if you want to boot the image at FE000000.
|
|
|
|
To change the HRCW in flash to boot the image at FEF00000, use these
|
|
U-Boot commands:
|
|
|
|
cp.b FE000000 1000 10000 ; copy 1st flash sector to 1000
|
|
mw.b 1020 b4 8 ; modify BMS bit
|
|
protect off FE000000 +10000
|
|
erase FE000000 +10000
|
|
cp.b 1000 FE000000 10000
|
|
|
|
7. Notes
|
|
1) The console baudrate for MPC8349EITX is 115200bps.
|