u-boot/arch/arm/dts/zynq-zybo-z7.dts
Michal Simek ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00

81 lines
1.2 KiB
Text

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2011 - 2015 Xilinx
* Copyright (C) 2012 National Instruments Corp.
*/
/dts-v1/;
#include "zynq-7000.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Digilent Zybo Z7 board";
compatible = "digilent,zynq-zybo-z7", "xlnx,zynq-7000";
aliases {
ethernet0 = &gem0;
serial0 = &uart1;
spi0 = &qspi;
mmc0 = &sdhci0;
};
memory@0 {
device_type = "memory";
reg = <0x0 0x40000000>;
};
chosen {
bootargs = "";
stdout-path = "serial0:115200n8";
};
gpio-leds {
compatible = "gpio-leds";
led-ld4 {
label = "zynq-zybo-z7:green:ld4";
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
};
};
usb_phy0: phy0 {
#phy-cells = <0>;
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
};
};
&clkc {
ps-clk-frequency = <33333333>;
};
&gem0 {
status = "okay";
phy-mode = "rgmii-id";
phy-handle = <&ethernet_phy>;
ethernet_phy: ethernet-phy@0 {
reg = <0>;
device_type = "ethernet-phy";
};
};
&qspi {
u-boot,dm-pre-reloc;
status = "okay";
};
&sdhci0 {
u-boot,dm-pre-reloc;
status = "okay";
};
&uart1 {
u-boot,dm-pre-reloc;
status = "okay";
};
&usb0 {
status = "okay";
dr_mode = "host";
usb-phy = <&usb_phy0>;
};