mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
da3dd417d7
Remove NXP powerpc P1020UTM board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
64 lines
2.5 KiB
Text
64 lines
2.5 KiB
Text
Overview
|
|
--------
|
|
P1_P2_RDB_PC represents a set of boards including
|
|
P1020MSBG-PC
|
|
P1020RDB-PC
|
|
P1020RDB-PD
|
|
P1021RDB-PC
|
|
P1024RDB
|
|
P2020RDB-PC
|
|
|
|
They have similar design of P1020RDB but have DDR3 instead of DDR2. P2020RDB-PC
|
|
has 64-bit DDR. All others have 32-bit DDR.
|
|
|
|
Key features on these boards include:
|
|
* DDR3
|
|
* NOR flash
|
|
* NAND flash (on RDB's only)
|
|
* SPI flash (on RDB's only)
|
|
* SDHC/MMC card slot
|
|
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
|
|
* PCIE slot and mini-PCIE slots
|
|
|
|
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
|
|
is used to store SPD data. In case of absent or corrupted SPD, falling back
|
|
to timing data embedded in the source code will be used. Raw timing data is
|
|
extracted from DDR chip datasheet. Different speeds of DDR are supported with
|
|
this approach. ODT option is forced to fit this set of boards, again because
|
|
they don't have regular DIMMs.
|
|
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification
|
|
for writing timing.
|
|
|
|
VSC firmware Address is defined by default in config file for eTSEC1.
|
|
|
|
SD width is based off DIP switch. DIP switch is detected on the
|
|
board by reading i2c bus and setting the appropriate mux values.
|
|
|
|
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have
|
|
pins multiplexing. QE function needs to be disabled to access Nor Flash and
|
|
CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
|
|
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
|
|
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
|
|
|
|
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
|
|
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
|
|
|
|
Device tree support and how to enable it for different configs
|
|
--------------------------------------------------------------
|
|
Device tree support is available for p1020rdb and p2020rdb for below mentioned boot,
|
|
1. NOR Boot
|
|
2. NAND Boot
|
|
3. SD Boot
|
|
4. SPIFLASH Boot
|
|
|
|
To enable device tree support for other boot, below configs need to be
|
|
enabled in relative defconfig file,
|
|
1. CONFIG_DEFAULT_DEVICE_TREE="p1020rdb" (Change default device tree name if required)
|
|
2. CONFIG_OF_CONTROL
|
|
3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at
|
|
CONFIG_RESET_VECTOR_ADDRESS - 0xffc
|
|
|
|
If device tree support is enabled in defconfig,
|
|
1. use 'u-boot-with-dtb.bin' for NOR boot.
|
|
2. use 'u-boot-with-spl.bin' for other boot.
|