Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-08 22:24:32 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/hisilicon/hikey
History
Simon Glass 401d1c4f5d common: Drop asm/global_data.h from common header 
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
..
build-tf.mak Consistently use nproc for counting the CPUs 2020-01-30 13:30:35 -05:00
hikey.c common: Drop asm/global_data.h from common header 2021-02-02 15:33:42 -05:00
Kconfig Convert all of CONFIG_CONS_INDEX to Kconfig 2018-03-16 10:28:52 -04:00
MAINTAINERS MAINTAINERS: Add myself as maintainer for hikey 2016-04-25 15:10:31 -04:00
Makefile SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
README hisilicon: hikey: Update instructions based on latest source 2018-08-31 11:59:44 -04:00

README 

Introduction
============

HiKey is the first certified 96Boards Consumer Edition board. The board/SoC has: -
* HiSilicon Kirin 6220 eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz.
* ARM Mali 450-MP4 GPU
* 1GB 800MHz LPDDR3 DRAM
* 4GB eMMC Flash Storage
* microSD
* 802.11a/b/g/n WiFi, Bluetooth

The HiKey schematic can be found here: -
https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/HiKey_schematics_LeMaker_version_Rev_A1.pdf

The SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf

Currently the u-boot port supports: -
* USB
* eMMC
* SD card
* GPIO

The HiKey U-Boot port has been tested with l-loader, booting ATF, which then boots
U-Boot as the bl33.bin executable.

Compile from source
===================

First get all the sources

  > mkdir -p ~/hikey/src ~/hikey/bin
  > cd ~/hikey/src
  > git clone https://github.com/96boards-hikey/edk2 -b testing/hikey960_v2.5
  > git clone https://github.com/ARM-software/arm-trusted-firmware
  > git clone https://github.com/96boards-hikey/l-loader -b testing/hikey960_v1.2
  > git clone https://github.com/96boards-hikey/OpenPlatformPkg -b testing/hikey960_v1.3.4
  > git clone https://github.com/96boards-hikey/atf-fastboot
  > wget https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/hisi-idt.py

Get the BL30 mcuimage.bin binary. It is shipped as part of the UEFI source.
The latest version can be obtained from the OpenPlatformPkg repo.

  > cp OpenPlatformPkg/Platforms/Hisilicon/HiKey/Binary/mcuimage.bin ~/hikey/bin/

Get nvme.img binary
  > wget -P ~/hikey/bin https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/nvme.img

Compile U-Boot
==============

  > cd ~/hikey/src/u-boot
  > make CROSS_COMPILE=aarch64-linux-gnu- hikey_config
  > make CROSS_COMPILE=aarch64-linux-gnu-
  > cp u-boot.bin ~/hikey/bin

Compile ARM Trusted Firmware (ATF)
==================================

  > cd ~/hikey/src/arm-trusted-firmware
  > make CROSS_COMPILE=aarch64-linux-gnu- all fip \
    SCP_BL2=~/hikey/bin/mcuimage.bin \
    BL33=~/hikey/bin/u-boot.bin DEBUG=1 PLAT=hikey

Copy the resulting FIP binary
  > cp build/hikey/debug/fip.bin ~/hikey/bin

Compile ATF Fastboot
====================

  > cd ~/hikey/src/atf-fastboot
  > make CROSS_COMPILE=aarch64-linux-gnu- PLAT=hikey DEBUG=1

Compile l-loader
================
  > cd ~/hikey/src/l-loader
  > ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl1.bin
  > ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl2.bin
  > ln -sf ~/hikey/src/atf-fastboot/build/hikey/debug/bl1.bin fastboot.bin
  > make hikey PTABLE_LST=aosp-8g

Copy the resulting binaries
  > cp *.img ~/hikey/bin
  > cp l-loader.bin ~/hikey/bin
  > cp recovery.bin ~/hikey/bin

These instructions are adapted from
https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/hikey.rst

FLASHING
========

1. Connect the second jumper on J15 BOOT SEL, to go into recovery mode and flash l-loader.bin with
the hisi-idt.py utility. Then connect a USB A to B mini cable from your PC to the USB OTG port of HiKey and execute the below command.

The command below assumes HiKey enumerated as the first USB serial port

  > sudo python ~/hikey/src/hisi-idt.py -d /dev/ttyUSB0 --img1 ~/hikey/bin/recovery.bin

2. Once LED 0 comes on solid, HiKey board should be detected as a fastboot device.

  > sudo fastboot devices

0123456789ABCDEF	fastboot

3. Flash the images

  > sudo fastboot flash ptable ~/hikey/bin/prm_ptable.img
  > sudo fastboot flash loader ~/hikey/bin/l-loader.bin
  > sudo fastboot flash fastboot ~/hikey/bin/fip.bin
  > sudo fastboot flash nvme ~/hikey/bin/nvme.img

4. Disconnect second jumper on J15 BOOT SEL, and reset the board and you will now (hopefully)
   have ATF, booting u-boot from eMMC.

   Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
   will get 'dwc_otg_core_host_init: Timeout!' errors.

See working boot trace below on UART3 available at Low Speed Expansion header: -

NOTICE:  BL2: v1.5(debug):v1.5-694-g6d4f6aea
NOTICE:  BL2: Built : 09:21:42, Aug 29 2018
INFO:    BL2: Doing platform setup
INFO:    ddr3 rank1 init pass
INFO:    succeed to set ddrc 150mhz
INFO:    ddr3 rank1 init pass
INFO:    succeed to set ddrc 266mhz
INFO:    ddr3 rank1 init pass
INFO:    succeed to set ddrc 400mhz
INFO:    ddr3 rank1 init pass
INFO:    succeed to set ddrc 533mhz
INFO:    ddr3 rank1 init pass
INFO:    succeed to set ddrc 800mhz
INFO:    Samsung DDR
INFO:    ddr test value:0xa5a55a5a
INFO:    BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000
INFO:    BL2: TrustZone: protecting 4194304 bytes of memory at 0x3e800000
INFO:    [BDID] [fff91c18] midr: 0x410fd033
INFO:    init_acpu_dvfs: pmic version 17
INFO:    init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00.
INFO:    acpu_dvfs_volt_init: success!
INFO:    acpu_dvfs_set_freq: support freq num is 5
INFO:    acpu_dvfs_set_freq: start prof is 0x4
INFO:    acpu_dvfs_set_freq: magic is 0x5a5ac5c5
INFO:    acpu_dvfs_set_freq: voltage:
INFO:      - 0: 0x49
INFO:      - 1: 0x49
INFO:      - 2: 0x50
INFO:      - 3: 0x60
INFO:      - 4: 0x78
NOTICE:  acpu_dvfs_set_freq: set acpu freq success!INFO:    BL2: Loading image id 2
INFO:    Loading image id=2 at address 0x1000000
INFO:    Image id=2 loaded: 0x1000000 - 0x1023d00
INFO:    hisi_mcu_load_image: mcu sections 0:
INFO:    hisi_mcu_load_image:  src  = 0x1000200
INFO:    hisi_mcu_load_image:  dst  = 0xf6000000
INFO:    hisi_mcu_load_image:  size = 31184
INFO:    hisi_mcu_load_image:  [SRC 0x1000200] 0x8000 0x3701 0x7695 0x7689
INFO:    hisi_mcu_load_image:  [DST 0xf6000000] 0x8000 0x3701 0x7695 0x7689
INFO:    hisi_mcu_load_image: mcu sections 1:
INFO:    hisi_mcu_load_image:  src  = 0x1007bd0
INFO:    hisi_mcu_load_image:  dst  = 0x5e00000
INFO:    hisi_mcu_load_image:  size = 93828
INFO:    hisi_mcu_load_image:  [SRC 0x1007bd0] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57
INFO:    hisi_mcu_load_image:  [DST 0x5e00000] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57
INFO:    hisi_mcu_load_image: mcu sections 2:
INFO:    hisi_mcu_load_image:  src  = 0x101ea54
INFO:    hisi_mcu_load_image:  dst  = 0x5e16e84
INFO:    hisi_mcu_load_image:  size = 15428
INFO:    hisi_mcu_load_image:  [SRC 0x101ea54] 0x9 0x1020640 0x10001 0x8f0d180
INFO:    hisi_mcu_load_image:  [DST 0x5e16e84] 0x9 0x1020640 0x10001 0x8f0d180
INFO:    hisi_mcu_load_image: mcu sections 3:
INFO:    hisi_mcu_load_image:  src  = 0x1022698
INFO:    hisi_mcu_load_image:  dst  = 0x5e22a10
INFO:    hisi_mcu_load_image:  size = 3060
INFO:    hisi_mcu_load_image:  [SRC 0x1022698] 0x0 0x0 0x0 0x0
INFO:    hisi_mcu_load_image:  [DST 0x5e22a10] 0x0 0x0 0x0 0x0
INFO:    hisi_mcu_load_image: mcu sections 4:
INFO:    hisi_mcu_load_image:  src  = 0x102328c
INFO:    hisi_mcu_load_image:  dst  = 0x5e23604
INFO:    hisi_mcu_load_image:  size = 2616
INFO:    hisi_mcu_load_image:  [SRC 0x102328c] 0xf80000a0 0x0 0xf80000ac 0x0
INFO:    hisi_mcu_load_image:  [DST 0x5e23604] 0xf80000a0 0x0 0xf80000ac 0x0
INFO:    hisi_mcu_start_run: AO_SC_SYS_CTRL2=0
INFO:    plat_hikey_bl2_handle_scp_bl2: MCU PC is at 0x42933301
INFO:    plat_hikey_bl2_handle_scp_bl2: AO_SC_PERIPH_CLKSTAT4 is 0x3b018f09
WARNING: BL2: Platform setup already done!!
INFO:    BL2: Loading image id 3
INFO:    Loading image id=3 at address 0xf9858000
INFO:    Image id=3 loaded: 0xf9858000 - 0xf9860058
INFO:    BL2: Loading image id 5
INFO:    Loading image id=5 at address 0x35000000
INFO:    Image id=5 loaded: 0x35000000 - 0x35061cd2
NOTICE:  BL2: Booting BL31
INFO:    Entry point address = 0xf9858000
INFO:    SPSR = 0x3cd
NOTICE:  BL31: v1.5(debug):v1.5-694-g6d4f6aea
NOTICE:  BL31: Built : 09:21:44, Aug 29 2018
WARNING: Using deprecated integer interrupt array in gicv2_driver_data_t
WARNING: Please migrate to using an interrupt_prop_t array
INFO:    ARM GICv2 driver initialized
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for disable_non_temporal_hint was applied
INFO:    BL31: cortex_a53: CPU workaround for 843419 was applied
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x35000000
INFO:    SPSR = 0x3c9


U-Boot 2018.09-rc1 (Aug 22 2018 - 14:55:49 +0530)hikey

DRAM:  990 MiB
HI6553 PMIC init
MMC:   config_sd_carddetect: SD card present
Hisilicon DWMMC: 0, Hisilicon DWMMC: 1
Loading Environment from FAT... Unable to use mmc 1:1... Failed (-5)
In:    uart@f7113000
Out:   uart@f7113000
Err:   uart@f7113000
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0
starting USB...
USB0:   scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
       scanning usb for ethernet devices... 0 Ethernet Device(s) found