mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-14 07:13:03 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
138 lines
3.6 KiB
C
138 lines
3.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* evm.c
|
|
*
|
|
* Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
|
|
* Antoine Tenart, <atenart@adeneo-embedded.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <environment.h>
|
|
#include <spl.h>
|
|
#include <netdev.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/ddr_defs.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mmc_host_def.h>
|
|
#include <asm/arch/mem.h>
|
|
#include <asm/arch/mux.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_init(void)
|
|
{
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
#if defined(CONFIG_NAND)
|
|
gpmc_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
uint8_t mac_addr[6];
|
|
uint32_t mac_hi, mac_lo;
|
|
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
|
|
printf("<ethaddr> not set. Reading from E-fuse\n");
|
|
/* try reading mac address from efuse */
|
|
mac_lo = readl(&cdev->macid0l);
|
|
mac_hi = readl(&cdev->macid0h);
|
|
mac_addr[0] = mac_hi & 0xFF;
|
|
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
|
|
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
|
|
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
|
|
mac_addr[4] = mac_lo & 0xFF;
|
|
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
|
|
|
|
if (is_valid_ethaddr(mac_addr))
|
|
eth_env_set_enetaddr("ethaddr", mac_addr);
|
|
else
|
|
printf("Unable to read MAC address. Set <ethaddr>\n");
|
|
}
|
|
|
|
return davinci_emac_initialize();
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
static struct module_pin_mux mmc_pin_mux[] = {
|
|
{ OFFSET(pincntl157), PULLDOWN_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl158), PULLDOWN_EN | PULLUDEN | MODE(0x0) },
|
|
{ OFFSET(pincntl159), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl160), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl161), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl162), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl163), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ -1 },
|
|
};
|
|
|
|
void set_uart_mux_conf(void) {}
|
|
|
|
void set_mux_conf_regs(void)
|
|
{
|
|
configure_module_pin_mux(mmc_pin_mux);
|
|
}
|
|
|
|
/*
|
|
* EMIF Paramters. Refer the EMIF register documentation and the
|
|
* memory datasheet for details. This is for 796 MHz.
|
|
*/
|
|
#define EMIF_TIM1 0x1779C9FE
|
|
#define EMIF_TIM2 0x50608074
|
|
#define EMIF_TIM3 0x009F857F
|
|
#define EMIF_SDREF 0x10001841
|
|
#define EMIF_SDCFG 0x62A73832
|
|
#define EMIF_PHYCFG 0x00000110
|
|
static const struct emif_regs ddr3_emif_regs = {
|
|
.sdram_config = EMIF_SDCFG,
|
|
.ref_ctrl = EMIF_SDREF,
|
|
.sdram_tim1 = EMIF_TIM1,
|
|
.sdram_tim2 = EMIF_TIM2,
|
|
.sdram_tim3 = EMIF_TIM3,
|
|
.emif_ddr_phy_ctlr_1 = EMIF_PHYCFG,
|
|
};
|
|
|
|
static const struct cmd_control ddr3_ctrl = {
|
|
.cmd0csratio = 0x100,
|
|
.cmd0iclkout = 0x001,
|
|
.cmd1csratio = 0x100,
|
|
.cmd1iclkout = 0x001,
|
|
.cmd2csratio = 0x100,
|
|
.cmd2iclkout = 0x001,
|
|
};
|
|
|
|
/* These values are obtained from the CCS app */
|
|
#define RD_DQS_GATE (0x1B3)
|
|
#define RD_DQS (0x35)
|
|
#define WR_DQS (0x93)
|
|
static struct ddr_data ddr3_data = {
|
|
.datardsratio0 = ((RD_DQS<<10) | (RD_DQS<<0)),
|
|
.datawdsratio0 = ((WR_DQS<<10) | (WR_DQS<<0)),
|
|
.datawiratio0 = ((0x20<<10) | 0x20<<0),
|
|
.datagiratio0 = ((0x20<<10) | 0x20<<0),
|
|
.datafwsratio0 = ((RD_DQS_GATE<<10) | (RD_DQS_GATE<<0)),
|
|
.datawrsratio0 = (((WR_DQS+0x40)<<10) | ((WR_DQS+0x40)<<0)),
|
|
};
|
|
|
|
static const struct dmm_lisa_map_regs evm_lisa_map_regs = {
|
|
.dmm_lisa_map_0 = 0x00000000,
|
|
.dmm_lisa_map_1 = 0x00000000,
|
|
.dmm_lisa_map_2 = 0x80640300,
|
|
.dmm_lisa_map_3 = 0xC0640320,
|
|
};
|
|
|
|
void sdram_init(void)
|
|
{
|
|
/*
|
|
* Pass in our DDR3 config information and that we have 2 EMIFs to
|
|
* configure.
|
|
*/
|
|
config_ddr(&ddr3_data, &ddr3_ctrl, &ddr3_emif_regs,
|
|
&evm_lisa_map_regs, 2);
|
|
}
|
|
#endif /* CONFIG_SPL_BUILD */
|