u-boot/board/samsung/trats/trats.c
Simon Glass 7f1961018c dm: exynos: Make sure that GPIOs are requested
With driver model GPIOs must be requested before use. Make sure this is
done correctly.

(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:33 -06:00

608 lines
16 KiB
C

/*
* Copyright (C) 2011 Samsung Electronics
* Heungjun Kim <riverful.kim@samsung.com>
* Kyungmin Park <kyungmin.park@samsung.com>
* Donghwa Lee <dh09.lee@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <lcd.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/cpu.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/clock.h>
#include <asm/arch/mipi_dsim.h>
#include <asm/arch/watchdog.h>
#include <asm/arch/power.h>
#include <power/pmic.h>
#include <usb/s3c_udc.h>
#include <power/max8997_pmic.h>
#include <power/max8997_muic.h>
#include <power/battery.h>
#include <power/max17042_fg.h>
#include <libtizen.h>
#include <usb.h>
#include <usb_mass_storage.h>
#include "setup.h"
DECLARE_GLOBAL_DATA_PTR;
unsigned int board_rev;
#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return board_rev;
}
#endif
static void check_hw_revision(void);
struct s3c_plat_otg_data s5pc210_otg_data;
int exynos_init(void)
{
check_hw_revision();
printf("HW Revision:\t0x%x\n", board_rev);
return 0;
}
void i2c_init_board(void)
{
int err;
/* I2C_5 -> PMIC */
err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
if (err) {
debug("I2C%d not configured\n", (I2C_5));
return;
}
/* I2C_8 -> FG */
gpio_request(EXYNOS4_GPIO_Y40, "i2c_clk");
gpio_request(EXYNOS4_GPIO_Y41, "i2c_data");
gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
}
static void trats_low_power_mode(void)
{
struct exynos4_clock *clk =
(struct exynos4_clock *)samsung_get_base_clock();
struct exynos4_power *pwr =
(struct exynos4_power *)samsung_get_base_power();
/* Power down CORE1 */
/* LOCAL_PWR_CFG [1:0] 0x3 EN, 0x0 DIS */
writel(0x0, &pwr->arm_core1_configuration);
/* Change the APLL frequency */
/* ENABLE (1 enable) | LOCKED (1 locked) */
/* [31] | [29] */
/* FSEL | MDIV | PDIV | SDIV */
/* [27] | [25:16] | [13:8] | [2:0] */
writel(0xa0c80604, &clk->apll_con0);
/* Change CPU0 clock divider */
/* CORE2_RATIO | APLL_RATIO | PCLK_DBG_RATIO | ATB_RATIO */
/* [30:28] | [26:24] | [22:20] | [18:16] */
/* PERIPH_RATIO | COREM1_RATIO | COREM0_RATIO | CORE_RATIO */
/* [14:12] | [10:8] | [6:4] | [2:0] */
writel(0x00000100, &clk->div_cpu0);
/* CLK_DIV_STAT_CPU0 - wait until clock gets stable (0 = stable) */
while (readl(&clk->div_stat_cpu0) & 0x1111111)
continue;
/* Change clock divider ratio for DMC */
/* DMCP_RATIO | DMCD_RATIO */
/* [22:20] | [18:16] */
/* DMC_RATIO | DPHY_RATIO | ACP_PCLK_RATIO | ACP_RATIO */
/* [14:12] | [10:8] | [6:4] | [2:0] */
writel(0x13113117, &clk->div_dmc0);
/* CLK_DIV_STAT_DMC0 - wait until clock gets stable (0 = stable) */
while (readl(&clk->div_stat_dmc0) & 0x11111111)
continue;
/* Turn off unnecessary power domains */
writel(0x0, &pwr->xxti_configuration); /* XXTI */
writel(0x0, &pwr->cam_configuration); /* CAM */
writel(0x0, &pwr->tv_configuration); /* TV */
writel(0x0, &pwr->mfc_configuration); /* MFC */
writel(0x0, &pwr->g3d_configuration); /* G3D */
writel(0x0, &pwr->gps_configuration); /* GPS */
writel(0x0, &pwr->gps_alive_configuration); /* GPS_ALIVE */
/* Turn off unnecessary clocks */
writel(0x0, &clk->gate_ip_cam); /* CAM */
writel(0x0, &clk->gate_ip_tv); /* TV */
writel(0x0, &clk->gate_ip_mfc); /* MFC */
writel(0x0, &clk->gate_ip_g3d); /* G3D */
writel(0x0, &clk->gate_ip_image); /* IMAGE */
writel(0x0, &clk->gate_ip_gps); /* GPS */
}
static int pmic_init_max8997(void)
{
struct pmic *p = pmic_get("MAX8997_PMIC");
int i = 0, ret = 0;
u32 val;
if (pmic_probe(p))
return -1;
/* BUCK1 VARM: 1.2V */
val = (1200000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK1DVS1, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK1CTRL, val);
/* BUCK2 VINT: 1.1V */
val = (1100000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK2DVS1, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK2CTRL, val);
/* BUCK3 G3D: 1.1V - OFF */
ret |= pmic_reg_read(p, MAX8997_REG_BUCK3CTRL, &val);
val &= ~ENBUCK;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK3CTRL, val);
val = (1100000 - 750000) / 50000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK3DVS, val);
/* BUCK4 CAMISP: 1.2V - OFF */
ret |= pmic_reg_read(p, MAX8997_REG_BUCK4CTRL, &val);
val &= ~ENBUCK;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK4CTRL, val);
val = (1200000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK4DVS, val);
/* BUCK5 VMEM: 1.2V */
val = (1200000 - 650000) / 25000;
for (i = 0; i < 8; i++)
ret |= pmic_reg_write(p, MAX8997_REG_BUCK5DVS1 + i, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK5CTRL, val);
/* BUCK6 CAM AF: 2.8V */
/* No Voltage Setting Register */
/* GNSLCT 3.0X */
val = GNSLCT;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK6CTRL, val);
/* BUCK7 VCC_SUB: 2.0V */
val = (2000000 - 750000) / 50000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK7DVS, val);
/* LDO1 VADC: 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO1CTRL, val);
/* LDO1 Disable active discharging */
ret |= pmic_reg_read(p, MAX8997_REG_LDO1CONFIG, &val);
val &= ~LDO_ADE;
ret |= pmic_reg_write(p, MAX8997_REG_LDO1CONFIG, val);
/* LDO2 VALIVE: 1.1V */
val = max8997_reg_ldo(1100000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO2CTRL, val);
/* LDO3 VUSB/MIPI: 1.1V */
val = max8997_reg_ldo(1100000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, val);
/* LDO4 VMIPI: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO4CTRL, val);
/* LDO5 VHSIC: 1.2V */
val = max8997_reg_ldo(1200000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO5CTRL, val);
/* LDO6 VCC_1.8V_PDA: 1.8V */
val = max8997_reg_ldo(1800000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO6CTRL, val);
/* LDO7 CAM_ISP: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO7CTRL, val);
/* LDO8 VDAC/VUSB: 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, val);
/* LDO9 VCC_2.8V_PDA: 2.8V */
val = max8997_reg_ldo(2800000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO9CTRL, val);
/* LDO10 VPLL: 1.1V */
val = max8997_reg_ldo(1100000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO10CTRL, val);
/* LDO11 TOUCH: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO11CTRL, val);
/* LDO12 VTCAM: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO12CTRL, val);
/* LDO13 VCC_3.0_LCD: 3.0V */
val = max8997_reg_ldo(3000000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO13CTRL, val);
/* LDO14 MOTOR: 3.0V */
val = max8997_reg_ldo(3000000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO14CTRL, val);
/* LDO15 LED_A: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO15CTRL, val);
/* LDO16 CAM_SENSOR: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO16CTRL, val);
/* LDO17 VTF: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO17CTRL, val);
/* LDO18 TOUCH_LED 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO18CTRL, val);
/* LDO21 VDDQ: 1.2V */
val = max8997_reg_ldo(1200000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO21CTRL, val);
/* SAFEOUT for both 1 and 2: 4.9V, Active discharge, Enable */
val = (SAFEOUT_4_90V << 0) | (SAFEOUT_4_90V << 2) |
ACTDISSAFEO1 | ACTDISSAFEO2 | ENSAFEOUT1 | ENSAFEOUT2;
ret |= pmic_reg_write(p, MAX8997_REG_SAFEOUTCTRL, val);
if (ret) {
puts("MAX8997 PMIC setting error!\n");
return -1;
}
return 0;
}
int exynos_power_init(void)
{
int chrg, ret;
struct power_battery *pb;
struct pmic *p_fg, *p_chrg, *p_muic, *p_bat;
/*
* For PMIC/MUIC the I2C bus is named as I2C5, but it is connected
* to logical I2C adapter 0
*
* The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
* to logical I2C adapter 1
*/
ret = pmic_init(I2C_5);
ret |= pmic_init_max8997();
ret |= power_fg_init(I2C_9);
ret |= power_muic_init(I2C_5);
ret |= power_bat_init(0);
if (ret)
return ret;
p_fg = pmic_get("MAX17042_FG");
if (!p_fg) {
puts("MAX17042_FG: Not found\n");
return -ENODEV;
}
p_chrg = pmic_get("MAX8997_PMIC");
if (!p_chrg) {
puts("MAX8997_PMIC: Not found\n");
return -ENODEV;
}
p_muic = pmic_get("MAX8997_MUIC");
if (!p_muic) {
puts("MAX8997_MUIC: Not found\n");
return -ENODEV;
}
p_bat = pmic_get("BAT_TRATS");
if (!p_bat) {
puts("BAT_TRATS: Not found\n");
return -ENODEV;
}
p_fg->parent = p_bat;
p_chrg->parent = p_bat;
p_muic->parent = p_bat;
p_bat->low_power_mode = trats_low_power_mode;
p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic);
pb = p_bat->pbat;
chrg = p_muic->chrg->chrg_type(p_muic);
debug("CHARGER TYPE: %d\n", chrg);
if (!p_chrg->chrg->chrg_bat_present(p_chrg)) {
puts("No battery detected\n");
return 0;
}
p_fg->fg->fg_battery_check(p_fg, p_bat);
if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
puts("CHARGE Battery !\n");
return 0;
}
static unsigned int get_hw_revision(void)
{
int hwrev = 0;
char str[10];
int i;
/* hw_rev[3:0] == GPE1[3:0] */
for (i = 0; i < 4; i++) {
int pin = i + EXYNOS4_GPIO_E10;
sprintf(str, "hw_rev%d", i);
gpio_request(pin, str);
gpio_cfg_pin(pin, S5P_GPIO_INPUT);
gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
}
udelay(1);
for (i = 0; i < 4; i++)
hwrev |= (gpio_get_value(EXYNOS4_GPIO_E10 + i) << i);
debug("hwrev 0x%x\n", hwrev);
return hwrev;
}
static void check_hw_revision(void)
{
int hwrev;
hwrev = get_hw_revision();
board_rev |= hwrev;
}
#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
int ret = 0;
u32 val = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return -1;
if (on) {
ret |= pmic_set_output(p, MAX8997_REG_SAFEOUTCTRL,
ENSAFEOUT1, LDO_ON);
ret |= pmic_reg_read(p, MAX8997_REG_LDO3CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, EN_LDO | val);
ret |= pmic_reg_read(p, MAX8997_REG_LDO8CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, EN_LDO | val);
} else {
ret |= pmic_reg_read(p, MAX8997_REG_LDO8CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, DIS_LDO | val);
ret |= pmic_reg_read(p, MAX8997_REG_LDO3CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, DIS_LDO | val);
ret |= pmic_set_output(p, MAX8997_REG_SAFEOUTCTRL,
ENSAFEOUT1, LDO_OFF);
}
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
struct s3c_plat_otg_data s5pc210_otg_data = {
.phy_control = s5pc210_phy_control,
.regs_phy = EXYNOS4_USBPHY_BASE,
.regs_otg = EXYNOS4_USBOTG_BASE,
.usb_phy_ctrl = EXYNOS4_USBPHY_CONTROL,
.usb_flags = PHY0_SLEEP,
};
int board_usb_init(int index, enum usb_init_type init)
{
debug("USB_udc_probe\n");
return s3c_udc_probe(&s5pc210_otg_data);
}
int g_dnl_board_usb_cable_connected(void)
{
struct pmic *muic = pmic_get("MAX8997_MUIC");
if (!muic)
return 0;
return !!muic->chrg->chrg_type(muic);
}
#endif
static void pmic_reset(void)
{
gpio_direction_output(EXYNOS4_GPIO_X07, 1);
gpio_set_pull(EXYNOS4_GPIO_X27, S5P_GPIO_PULL_NONE);
}
static void board_clock_init(void)
{
struct exynos4_clock *clk =
(struct exynos4_clock *)samsung_get_base_clock();
writel(CLK_SRC_CPU_VAL, (unsigned int)&clk->src_cpu);
writel(CLK_SRC_TOP0_VAL, (unsigned int)&clk->src_top0);
writel(CLK_SRC_FSYS_VAL, (unsigned int)&clk->src_fsys);
writel(CLK_SRC_PERIL0_VAL, (unsigned int)&clk->src_peril0);
writel(CLK_DIV_CPU0_VAL, (unsigned int)&clk->div_cpu0);
writel(CLK_DIV_CPU1_VAL, (unsigned int)&clk->div_cpu1);
writel(CLK_DIV_DMC0_VAL, (unsigned int)&clk->div_dmc0);
writel(CLK_DIV_DMC1_VAL, (unsigned int)&clk->div_dmc1);
writel(CLK_DIV_LEFTBUS_VAL, (unsigned int)&clk->div_leftbus);
writel(CLK_DIV_RIGHTBUS_VAL, (unsigned int)&clk->div_rightbus);
writel(CLK_DIV_TOP_VAL, (unsigned int)&clk->div_top);
writel(CLK_DIV_FSYS1_VAL, (unsigned int)&clk->div_fsys1);
writel(CLK_DIV_FSYS2_VAL, (unsigned int)&clk->div_fsys2);
writel(CLK_DIV_FSYS3_VAL, (unsigned int)&clk->div_fsys3);
writel(CLK_DIV_PERIL0_VAL, (unsigned int)&clk->div_peril0);
writel(CLK_DIV_PERIL3_VAL, (unsigned int)&clk->div_peril3);
writel(PLL_LOCKTIME, (unsigned int)&clk->apll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->mpll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->epll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->vpll_lock);
writel(APLL_CON1_VAL, (unsigned int)&clk->apll_con1);
writel(APLL_CON0_VAL, (unsigned int)&clk->apll_con0);
writel(MPLL_CON1_VAL, (unsigned int)&clk->mpll_con1);
writel(MPLL_CON0_VAL, (unsigned int)&clk->mpll_con0);
writel(EPLL_CON1_VAL, (unsigned int)&clk->epll_con1);
writel(EPLL_CON0_VAL, (unsigned int)&clk->epll_con0);
writel(VPLL_CON1_VAL, (unsigned int)&clk->vpll_con1);
writel(VPLL_CON0_VAL, (unsigned int)&clk->vpll_con0);
writel(CLK_GATE_IP_CAM_VAL, (unsigned int)&clk->gate_ip_cam);
writel(CLK_GATE_IP_VP_VAL, (unsigned int)&clk->gate_ip_tv);
writel(CLK_GATE_IP_MFC_VAL, (unsigned int)&clk->gate_ip_mfc);
writel(CLK_GATE_IP_G3D_VAL, (unsigned int)&clk->gate_ip_g3d);
writel(CLK_GATE_IP_IMAGE_VAL, (unsigned int)&clk->gate_ip_image);
writel(CLK_GATE_IP_LCD0_VAL, (unsigned int)&clk->gate_ip_lcd0);
writel(CLK_GATE_IP_LCD1_VAL, (unsigned int)&clk->gate_ip_lcd1);
writel(CLK_GATE_IP_FSYS_VAL, (unsigned int)&clk->gate_ip_fsys);
writel(CLK_GATE_IP_GPS_VAL, (unsigned int)&clk->gate_ip_gps);
writel(CLK_GATE_IP_PERIL_VAL, (unsigned int)&clk->gate_ip_peril);
writel(CLK_GATE_IP_PERIR_VAL, (unsigned int)&clk->gate_ip_perir);
writel(CLK_GATE_BLOCK_VAL, (unsigned int)&clk->gate_block);
}
static void board_power_init(void)
{
struct exynos4_power *pwr =
(struct exynos4_power *)samsung_get_base_power();
/* PS HOLD */
writel(EXYNOS4_PS_HOLD_CON_VAL, (unsigned int)&pwr->ps_hold_control);
/* Set power down */
writel(0, (unsigned int)&pwr->cam_configuration);
writel(0, (unsigned int)&pwr->tv_configuration);
writel(0, (unsigned int)&pwr->mfc_configuration);
writel(0, (unsigned int)&pwr->g3d_configuration);
writel(0, (unsigned int)&pwr->lcd1_configuration);
writel(0, (unsigned int)&pwr->gps_configuration);
writel(0, (unsigned int)&pwr->gps_alive_configuration);
/* It is necessary to power down core 1 */
/* to successfully boot CPU1 in kernel */
writel(0, (unsigned int)&pwr->arm_core1_configuration);
}
static void exynos_uart_init(void)
{
/* UART_SEL GPY4[7] (part2) at EXYNOS4 */
gpio_request(EXYNOS4_GPIO_Y47, "uart_sel");
gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4_GPIO_Y47, 1);
}
int exynos_early_init_f(void)
{
wdt_stop();
pmic_reset();
board_clock_init();
exynos_uart_init();
board_power_init();
return 0;
}
void exynos_reset_lcd(void)
{
gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 0);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
}
int lcd_power(void)
{
int ret = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return 0;
/* LDO15 voltage: 2.2v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO15CTRL, 0x1c | EN_LDO);
/* LDO13 voltage: 3.0v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO13CTRL, 0x2c | EN_LDO);
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
int mipi_power(void)
{
int ret = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return 0;
/* LDO3 voltage: 1.1v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, 0x6 | EN_LDO);
/* LDO4 voltage: 1.8v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO4CTRL, 0x14 | EN_LDO);
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
void exynos_lcd_misc_init(vidinfo_t *vid)
{
#ifdef CONFIG_TIZEN
get_tizen_logo_info(vid);
#endif
#ifdef CONFIG_S6E8AX0
s6e8ax0_init();
setenv("lcdinfo", "lcd=s6e8ax0");
#endif
}