mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 05:34:28 +00:00
aa5bbfd961
When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)", the last not 512bytes aligned data wat cut off and not burned into SD card. Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only burned 1085440 bytes, the leaving 168 bytes were not burnned and cause boot issue. So update README dd command to add "conv=notrunc" Signed-off-by: Peng Fan <peng.fan@nxp.com>
82 lines
2.2 KiB
Text
82 lines
2.2 KiB
Text
How to use U-Boot on Freescale MX6UL 14x14 EVK
|
|
-----------------------------------------------
|
|
|
|
- Build U-Boot for MX6UL 14x14 EVK:
|
|
|
|
$ make mrproper
|
|
$ make mx6ul_14x14_evk_defconfig
|
|
$ make
|
|
|
|
This will generate the SPL image called SPL and the u-boot.img.
|
|
|
|
1. Booting via SDCard
|
|
---------------------
|
|
|
|
- Flash the SPL image into the micro SD card:
|
|
|
|
sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1 conv=notrunc; sync
|
|
|
|
- Flash the u-boot.img image into the micro SD card:
|
|
|
|
sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69 conv=notrunc; sync
|
|
|
|
- Jumper settings:
|
|
|
|
SW601: 0 0 1 0
|
|
Sw602: 1 0
|
|
|
|
where 0 means bottom position and 1 means top position (from the
|
|
switch label numbers reference).
|
|
|
|
- Connect the USB cable between the EVK and the PC for the console.
|
|
(The USB console connector is the one close the push buttons)
|
|
|
|
- Insert the micro SD card in the board, power it up and U-Boot messages should
|
|
come up.
|
|
|
|
2. Booting via Serial Download Protocol (SDP)
|
|
---------------------------------------------
|
|
|
|
The mx6ulevk board can boot from USB OTG port using the SDP, target will
|
|
enter in SDP mode in case an SD Card is not connect or boot switches are
|
|
set as below:
|
|
|
|
Sw602: 0 1
|
|
SW601: x x x x
|
|
|
|
The following tools can be used to boot via SDP, for both tools you must
|
|
connect an USB cable in USB OTG port.
|
|
|
|
- Method 1: Universal Update Utility (uuu)
|
|
|
|
The UUU binary can be downloaded in release tab from link below:
|
|
https://github.com/NXPmicro/mfgtools
|
|
|
|
The following script should be created to boot SPL + u-boot-dtb.img binaries:
|
|
|
|
$ cat uuu_script
|
|
uuu_version 1.1.4
|
|
|
|
SDP: boot -f SPL
|
|
SDPU: write -f u-boot-dtb.img -addr 0x877fffc0
|
|
SDPU: jump -addr 0x877fffc0
|
|
SDPU: done
|
|
|
|
Please note that the address above is calculated based on SYS_TEXT_BASE address:
|
|
|
|
0x877fffc0 = 0x87800000 (SYS_TEXT_BASE) - 0x40 (U-Boot proper Header size)
|
|
|
|
Power on the target and run the following command from U-Boot root directory:
|
|
|
|
$ sudo ./uuu uuu_script
|
|
|
|
- Method 2: imx usb loader tool (imx_usb):
|
|
|
|
The imx_usb_loader tool can be downloaded in link below:
|
|
https://github.com/boundarydevices/imx_usb_loader
|
|
|
|
Build the source code and run the following commands from U-Boot root
|
|
directory:
|
|
|
|
$ sudo ./imx_usb SPL
|
|
$ sudo ./imx_usb u-boot-dtb.img
|