u-boot/board/Synology/ds109/ds109.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

176 lines
3.7 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2009-2012
* Wojciech Dubowik <wojciech.dubowik@neratec.com>
* Luka Perkov <luka@openwrt.org>
*/
#include <common.h>
#include <miiphy.h>
#include <asm/setup.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include "ds109.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/*
* default gpio configuration
* There are maximum 64 gpios controlled through 2 sets of registers
* the below configuration configures mainly initial LED status
*/
mvebu_config_gpio(DS109_OE_VAL_LOW,
DS109_OE_VAL_HIGH,
DS109_OE_LOW, DS109_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
static const u32 kwmpp_config[] = {
MPP0_SPI_SCn, /* SPI Flash */
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
MPP3_SPI_MISO,
MPP4_GPIO,
MPP5_GPO,
MPP6_SYSRST_OUTn, /* Reset signal */
MPP7_GPO,
MPP8_TW_SDA, /* I2C */
MPP9_TW_SCK, /* I2C */
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP12_GPO,
MPP13_UART1_TXD,
MPP14_UART1_RXD,
MPP15_GPIO,
MPP16_GPIO,
MPP17_GPIO,
MPP18_GPO,
MPP19_GPO,
MPP20_SATA1_ACTn,
MPP21_SATA0_ACTn,
MPP22_GPIO, /* HDD2 FAIL LED */
MPP23_GPIO, /* HDD1 FAIL LED */
MPP24_GPIO,
MPP25_GPIO,
MPP26_GPIO,
MPP27_GPIO,
MPP28_GPIO,
MPP29_GPIO,
MPP30_GPIO,
MPP31_GPIO, /* HDD2 */
MPP32_GPIO, /* FAN A */
MPP33_GPIO, /* FAN B */
MPP34_GPIO, /* FAN C */
MPP35_GPIO, /* FAN SENSE */
MPP36_GPIO,
MPP37_GPIO,
MPP38_GPIO,
MPP39_GPIO,
MPP40_GPIO,
MPP41_GPIO,
MPP42_GPIO,
MPP43_GPIO,
MPP44_GPIO,
MPP45_GPIO,
MPP46_GPIO,
MPP47_GPIO,
MPP48_GPIO,
MPP49_GPIO,
0
};
kirkwood_mpp_conf(kwmpp_config, NULL);
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
return 0;
}
/* Synology reset uses UART */
#include <ns16550.h>
#define SOFTWARE_SHUTDOWN 0x31
#define SOFTWARE_REBOOT 0x43
#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE
void reset_misc(void)
{
int b_d;
printf("Synology reset...");
udelay(50000);
b_d = ns16550_calc_divisor((NS16550_t)CONFIG_SYS_NS16550_COM2,
CONFIG_SYS_NS16550_CLK, 9600);
NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM2, b_d);
NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM2, SOFTWARE_REBOOT);
}
/* Support old kernels */
void setup_board_tags(struct tag **in_params)
{
unsigned int boardId;
struct tag *params;
struct tag_mv_uboot *t;
int i;
printf("Synology board tags...");
params = *in_params;
t = (struct tag_mv_uboot *)&params->u;
t->uboot_version = VER_NUM;
boardId = SYNO_DS109_ID;
t->uboot_version |= boardId;
t->tclk = CONFIG_SYS_TCLK;
t->sysclk = CONFIG_SYS_TCLK*2;
t->isusbhost = 1;
for (i = 0; i < 4; i++) {
memset(t->macaddr[i], 0, sizeof(t->macaddr[i]));
t->mtu[i] = 0;
}
params->hdr.tag = ATAG_MV_UBOOT;
params->hdr.size = tag_size(tag_mv_uboot);
params = tag_next(params);
*in_params = params;
}
#ifdef CONFIG_RESET_PHY_R
/* Configure and enable MV88E1116 PHY */
void reset_phy(void)
{
u16 reg;
u16 devadr;
char *name = "egiga0";
if (miiphy_set_current_dev(name))
return;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
printf("Error: 88E1116 could not read PHY dev address\n");
return;
}
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 4.7.2 of chip datasheet
*/
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
/* reset the phy */
miiphy_reset(name, devadr);
printf("88E1116 Initialized on %s\n", name);
}
#endif /* CONFIG_RESET_PHY_R */