mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 13:56:30 +00:00
c2120fbfbc
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
322 lines
11 KiB
C
322 lines
11 KiB
C
/*
|
|
* (C) Copyright 2006-2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* Configuation settings for the PDNB3 board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
#define CONFIG_IXP425 1 /* This is an IXP425 CPU */
|
|
#define CONFIG_PDNB3 1 /* on an PDNB3 board */
|
|
|
|
#define CONFIG_MACH_TYPE 1002
|
|
|
|
#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
|
|
#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
|
|
|
|
/*
|
|
* Ethernet
|
|
*/
|
|
#define CONFIG_IXP4XX_NPE 1 /* include IXP4xx NPE support */
|
|
#define CONFIG_PHY_ADDR 16 /* NPE0 PHY address */
|
|
#define CONFIG_HAS_ETH1
|
|
#define CONFIG_PHY1_ADDR 18 /* NPE1 PHY address */
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
|
|
|
|
/*
|
|
* Misc configuration options
|
|
*/
|
|
#define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */
|
|
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */
|
|
|
|
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS 1
|
|
#define CONFIG_INITRD_TAG 1
|
|
|
|
/*
|
|
* Size of malloc() pool
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (1 << 20)
|
|
|
|
/* allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#define CONFIG_IXP_SERIAL
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_PING
|
|
|
|
#if !defined(CONFIG_SCPU)
|
|
#define CONFIG_CMD_NAND
|
|
#endif
|
|
|
|
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
|
|
|
|
#define CONFIG_IXP425_TIMER_CLK 66666666
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
/***************************************************************
|
|
* Platform/Board specific defines start here.
|
|
***************************************************************/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Default configuration (environment varibles...)
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
|
|
"echo"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"hostname=pdnb3\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} ethaddr=${ethaddr} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate} " \
|
|
"mtdparts=${mtdparts}\0" \
|
|
"flash_nfs=run nfsargs addip addtty;" \
|
|
"bootm ${kernel_addr}\0" \
|
|
"flash_self=run ramargs addip addtty;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
|
|
"bootm\0" \
|
|
"rootpath=/opt/buildroot\0" \
|
|
"bootfile=/tftpboot/netbox/uImage\0" \
|
|
"kernel_addr=50080000\0" \
|
|
"ramdisk_addr=50200000\0" \
|
|
"load=tftp 100000 /tftpboot/netbox/u-boot.bin\0" \
|
|
"update=protect off 50000000 5007dfff;era 50000000 5007dfff;" \
|
|
"cp.b 100000 50000000 ${filesize};" \
|
|
"setenv filesize;saveenv\0" \
|
|
"upd=run load update\0" \
|
|
"ipaddr=10.0.0.233\0" \
|
|
"serverip=10.0.0.152\0" \
|
|
"netmask=255.255.0.0\0" \
|
|
"ethaddr=c6:6f:13:36:f3:81\0" \
|
|
"eth1addr=c6:6f:13:36:f3:82\0" \
|
|
"mtdparts=IXP4XX-Flash.0:504k@0(uboot),4k@504k(env)," \
|
|
"4k@508k(renv)\0" \
|
|
""
|
|
#define CONFIG_BOOTCOMMAND "run net_nfs"
|
|
|
|
/*
|
|
* Physical Memory Map
|
|
*/
|
|
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
|
|
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
|
|
#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x50000000
|
|
#define CONFIG_SYS_FLASH_BASE 0x50000000
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#if defined(CONFIG_SCPU)
|
|
#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 512 kB for Monitor */
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN (504 << 10) /* Reserve 512 kB for Monitor */
|
|
#endif
|
|
|
|
/*
|
|
* Expansion bus settings
|
|
*/
|
|
#if defined(CONFIG_SCPU)
|
|
#define CONFIG_SYS_EXP_CS0 0x94d23C42 /* 8bit, max size */
|
|
#else
|
|
#define CONFIG_SYS_EXP_CS0 0x94913C43 /* 8bit, max size */
|
|
#endif
|
|
#define CONFIG_SYS_EXP_CS1 0x85000043 /* 8bit, 512bytes */
|
|
|
|
/*
|
|
* SDRAM settings
|
|
*/
|
|
#define CONFIG_SYS_SDR_CONFIG 0x18
|
|
#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
|
|
#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
|
|
|
|
/*
|
|
* FLASH and environment organization
|
|
*/
|
|
#if defined(CONFIG_SCPU)
|
|
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
|
|
#endif
|
|
|
|
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
|
|
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
|
|
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
|
|
/*
|
|
* The following defines are added for buggy IOP480 byte interface.
|
|
* All other boards should use the standard values (CPCI405 etc.)
|
|
*/
|
|
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
|
|
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
|
|
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#if defined(CONFIG_SCPU)
|
|
/* no redundant environment on SCPU */
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
#else
|
|
#define CONFIG_ENV_SECT_SIZE 0x1000 /* size of one complete sector */
|
|
#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
#endif
|
|
|
|
#if !defined(CONFIG_SCPU)
|
|
/*
|
|
* NAND-FLASH stuff
|
|
*/
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x51000000 /* NAND FLASH Base Address */
|
|
#endif
|
|
|
|
/*
|
|
* GPIO settings
|
|
*/
|
|
|
|
/* FPGA program pin configuration */
|
|
#define CONFIG_SYS_GPIO_PRG 12 /* FPGA program pin (cpu output)*/
|
|
#define CONFIG_SYS_GPIO_CLK 10 /* FPGA clk pin (cpu output) */
|
|
#define CONFIG_SYS_GPIO_DATA 14 /* FPGA data pin (cpu output) */
|
|
#define CONFIG_SYS_GPIO_INIT 13 /* FPGA init pin (cpu input) */
|
|
#define CONFIG_SYS_GPIO_DONE 11 /* FPGA done pin (cpu input) */
|
|
|
|
/* other GPIO's */
|
|
#define CONFIG_SYS_GPIO_RESTORE_INT 0
|
|
#define CONFIG_SYS_GPIO_RESTART_INT 1
|
|
#define CONFIG_SYS_GPIO_SYS_RUNNING 2
|
|
#define CONFIG_SYS_GPIO_PCI_INTA 3
|
|
#define CONFIG_SYS_GPIO_PCI_INTB 4
|
|
#define CONFIG_SYS_GPIO_I2C_SCL 6
|
|
#define CONFIG_SYS_GPIO_I2C_SDA 7
|
|
#define CONFIG_SYS_GPIO_FPGA_RESET 9
|
|
#define CONFIG_SYS_GPIO_CLK_33M 15
|
|
|
|
/*
|
|
* I2C stuff
|
|
*/
|
|
|
|
/* enable I2C and select the hardware/software driver */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
|
|
#define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */
|
|
#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
|
|
/*
|
|
* Software (bit-bang) I2C driver configuration
|
|
*/
|
|
#define PB_SCL (1 << CONFIG_SYS_GPIO_I2C_SCL)
|
|
#define PB_SDA (1 << CONFIG_SYS_GPIO_I2C_SDA)
|
|
|
|
#define I2C_INIT GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SCL)
|
|
#define I2C_ACTIVE GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SDA)
|
|
#define I2C_TRISTATE GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_I2C_SDA)
|
|
#define I2C_READ ((*IXP425_GPIO_GPINR & PB_SDA) != 0)
|
|
#define I2C_SDA(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SDA); \
|
|
else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SDA)
|
|
#define I2C_SCL(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SCL); \
|
|
else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SCL)
|
|
#define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */
|
|
|
|
/*
|
|
* I2C RTC
|
|
*/
|
|
#if 0 /* test-only */
|
|
#define CONFIG_RTC_DS1340 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#else
|
|
/* M41T11 Serial Access Timekeeper(R) SRAM */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with the linux driver */
|
|
#endif
|
|
|
|
/*
|
|
* Spartan3 FPGA configuration support
|
|
*/
|
|
#define CONFIG_SYS_FPGA_MAX_SIZE 700*1024 /* 700kByte for XC3S500E */
|
|
|
|
#define CONFIG_SYS_FPGA_PRG (1 << CONFIG_SYS_GPIO_PRG) /* FPGA program pin (cpu output)*/
|
|
#define CONFIG_SYS_FPGA_CLK (1 << CONFIG_SYS_GPIO_CLK) /* FPGA clk pin (cpu output) */
|
|
#define CONFIG_SYS_FPGA_DATA (1 << CONFIG_SYS_GPIO_DATA) /* FPGA data pin (cpu output) */
|
|
#define CONFIG_SYS_FPGA_INIT (1 << CONFIG_SYS_GPIO_INIT) /* FPGA init pin (cpu input) */
|
|
#define CONFIG_SYS_FPGA_DONE (1 << CONFIG_SYS_GPIO_DONE) /* FPGA done pin (cpu input) */
|
|
|
|
/*
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32
|
|
|
|
/* additions for new relocation code, must be added to all boards */
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
|
|
|
|
#endif /* __CONFIG_H */
|