mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 01:19:49 +00:00
5ace2992b5
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some early version silicons. The default settings of the DDR IO receiver biasing may not work at cold temperature. When a failure occurs, a DDR input latches an incorrect value. The workaround will set the receiver to an acceptable bias point. Signed-off-by: Gong Chen Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
98 lines
2.9 KiB
C
98 lines
2.9 KiB
C
/*
|
|
* Copyright 2008-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 as published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
|
|
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
|
|
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
|
|
#endif
|
|
|
|
void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
|
|
unsigned int ctrl_num)
|
|
{
|
|
unsigned int i;
|
|
#ifdef CONFIG_MPC83xx
|
|
ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC83xx_DDR_ADDR;
|
|
#else
|
|
ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC85xx_DDR_ADDR;
|
|
#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
|
|
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
uint svr;
|
|
#endif
|
|
#endif
|
|
|
|
if (ctrl_num) {
|
|
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
|
|
return;
|
|
}
|
|
|
|
#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
|
|
/*
|
|
* Set the DDR IO receiver to an acceptable bias point.
|
|
* Fixed in Rev 2.1.
|
|
*/
|
|
svr = get_svr();
|
|
if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0)) {
|
|
if ((regs->ddr_sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) ==
|
|
SDRAM_CFG_SDRAM_TYPE_DDR2)
|
|
out_be32(&gur->ddrioovcr, 0x90000000);
|
|
else
|
|
out_be32(&gur->ddrioovcr, 0xA8000000);
|
|
}
|
|
#endif
|
|
|
|
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
|
|
if (i == 0) {
|
|
out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs0_config, regs->cs[i].config);
|
|
|
|
} else if (i == 1) {
|
|
out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs1_config, regs->cs[i].config);
|
|
|
|
} else if (i == 2) {
|
|
out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs2_config, regs->cs[i].config);
|
|
|
|
} else if (i == 3) {
|
|
out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs3_config, regs->cs[i].config);
|
|
}
|
|
}
|
|
|
|
out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
|
|
out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
|
|
out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
|
|
out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
|
|
out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
|
|
out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
|
|
out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
|
|
out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
|
|
out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
|
|
out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
|
|
out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
|
|
out_be32(&ddr->init_addr, regs->ddr_init_addr);
|
|
out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
|
|
|
|
/*
|
|
* 200 painful micro-seconds must elapse between
|
|
* the DDR clock setup and the DDR config enable.
|
|
*/
|
|
udelay(200);
|
|
asm volatile("sync;isync");
|
|
|
|
out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
|
|
|
|
/* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */
|
|
while (in_be32(&ddr->sdram_cfg_2) & 0x10) {
|
|
udelay(10000); /* throttle polling rate */
|
|
}
|
|
}
|