u-boot/include/configs/ls1046afrwy.h
Alison Wang 64fb43dfae armv8: ls1046afrwy: Define CONFIG_ENV_ADDR for QSPI Boot
Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start
address of the flash sector containing the environment. It fixes
the issue that bootcmd is always set as default at bootup.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30

139 lines
3.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2019 NXP
*/
#ifndef __LS1046AFRWY_H__
#define __LS1046AFRWY_H__
#include "ls1046a_common.h"
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_SYS_UBOOT_BASE 0x40100000
/* IFC */
#define CONFIG_FSL_IFC
/*
* NAND Flash Definitions
*/
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE 0x7e800000
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_NAND \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
| CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \
| CSOR_NAND_PB(64)) /* 64 Pages Per Block */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x7) | \
FTIM0_NAND_TWH(0xa))
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0xe) | \
FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
FTIM2_NAND_TREH(0xa) | \
FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3 0x0
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
/* IFC Timing Params */
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define I2C_RETIMER_ADDR 0x18
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT 0x1 /* Channel 0*/
#define I2C_MUX_CH_RTC 0x1 /* Channel 0*/
/* RTC */
#define RTC
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 0 I2C bus 0*/
#define CONFIG_SYS_RTC_BUS_NUM 0
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x500000 /* 5MB */
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
#define CONFIG_SYS_FSL_QSPI_BASE 0x40000000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FSL_QSPI_BASE + \
CONFIG_ENV_OFFSET)
/* FMan */
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define QSGMII_PORT1_PHY_ADDR 0x1c
#define QSGMII_PORT2_PHY_ADDR 0x1d
#define QSGMII_PORT3_PHY_ADDR 0x1e
#define QSGMII_PORT4_PHY_ADDR 0x1f
#define FDT_SEQ_MACADDR_FROM_ENV
#define CONFIG_ETHPRIME "FM1@DTSEC3"
#endif
/* QSPI device */
#ifdef CONFIG_FSL_QSPI
#define FSL_QSPI_FLASH_SIZE SZ_64M
#define FSL_QSPI_FLASH_NUM 1
#endif
#undef CONFIG_BOOTCOMMAND
#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
"env exists secureboot && esbc_halt;;"
#define SD_BOOTCOMMAND "run distro_bootcmd;run sd_bootcmd; " \
"env exists secureboot && esbc_halt;"
#include <asm/fsl_secure_boot.h>
#endif /* __LS1046AFRWY_H__ */