mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-01 17:10:11 +00:00
56c4046038
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
65 lines
1.4 KiB
Text
65 lines
1.4 KiB
Text
CONFIG_ARM=y
|
|
CONFIG_TARGET_LS1021AIOT=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x100000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_SPL=y
|
|
CONFIG_SPL_TEXT_BASE=0x10000000
|
|
CONFIG_AHCI=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SD_BOOT,SD_BOOT_QSPI"
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_SPL_FSL_PBL=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8
|
|
CONFIG_CMD_BOOTZ=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_CMD_MEMINFO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
# CONFIG_CMD_MDIO is not set
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_EXT2=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_SF=y
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-iot-duart"
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_TSEC_ENET=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_SPL_DM_SPI=y
|
|
CONFIG_FSL_DSPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|