u-boot/board/renesas/gose/gose.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

149 lines
2.9 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* board/renesas/gose/gose.c
*
* Copyright (C) 2014 Renesas Electronics Corporation
*/
#include <common.h>
#include <malloc.h>
#include <dm.h>
#include <dm/platform_data/serial_sh.h>
#include <environment.h>
#include <asm/processor.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <linux/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
#include <asm/arch/rcar-mstp.h>
#include <asm/arch/sh_sdhi.h>
#include <netdev.h>
#include <miiphy.h>
#include <i2c.h>
#include "qos.h"
DECLARE_GLOBAL_DATA_PTR;
#define CLK2MHZ(clk) (clk / 1000 / 1000)
void s_init(void)
{
struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
u32 stc;
/* Watchdog init */
writel(0xA5A5A500, &rwdt->rwtcsra);
writel(0xA5A5A500, &swdt->swtcsra);
/* CPU frequency setting. Set to 1.5GHz */
stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT;
clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);
/* QoS */
qos_init();
}
#define TMU0_MSTP125 BIT(25)
#define SD1CKCR 0xE6150078
#define SD2CKCR 0xE615026C
#define SD_97500KHZ 0x7
int board_early_init_f(void)
{
mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
/*
* SD0 clock is set to 97.5MHz by default.
* Set SD1 and SD2 to the 97.5MHz as well.
*/
writel(SD_97500KHZ, SD1CKCR);
writel(SD_97500KHZ, SD2CKCR);
return 0;
}
#define ETHERNET_PHY_RESET 176 /* GPIO 5 22 */
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
/* Force ethernet PHY out of reset */
gpio_request(ETHERNET_PHY_RESET, "phy_reset");
gpio_direction_output(ETHERNET_PHY_RESET, 0);
mdelay(10);
gpio_direction_output(ETHERNET_PHY_RESET, 1);
return 0;
}
int dram_init(void)
{
if (fdtdec_setup_memory_size() != 0)
return -EINVAL;
return 0;
}
int dram_init_banksize(void)
{
fdtdec_setup_memory_banksize();
return 0;
}
/* KSZ8041RNLI */
#define PHY_CONTROL1 0x1E
#define PHY_LED_MODE 0xC0000
#define PHY_LED_MODE_ACK 0x4000
int board_phy_config(struct phy_device *phydev)
{
int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
ret &= ~PHY_LED_MODE;
ret |= PHY_LED_MODE_ACK;
ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
return 0;
}
void reset_cpu(ulong addr)
{
struct udevice *dev;
const u8 pmic_bus = 6;
const u8 pmic_addr = 0x58;
u8 data;
int ret;
ret = i2c_get_chip_for_busnum(pmic_bus, pmic_addr, 1, &dev);
if (ret)
hang();
ret = dm_i2c_read(dev, 0x13, &data, 1);
if (ret)
hang();
data |= BIT(1);
ret = dm_i2c_write(dev, 0x13, &data, 1);
if (ret)
hang();
}
enum env_location env_get_location(enum env_operation op, int prio)
{
const u32 load_magic = 0xb33fc0de;
/* Block environment access if loaded using JTAG */
if ((readl(CONFIG_SPL_TEXT_BASE + 0x24) == load_magic) &&
(op != ENVOP_INIT))
return ENVL_UNKNOWN;
if (prio)
return ENVL_UNKNOWN;
return ENVL_SPI_FLASH;
}