u-boot/include/configs/M5275EVB.h
Masahiro Yamada d4a9b17df5 m68k: mcf52x2: move CPU type to Kconfig and refactor config.mk
This commit intends to stop grepping CPU type in
arch/m68k/cpu/mcf52x2/config.mk.

Move the CPU type config options from include/configs/*.h
to arch/m68k/Kconfig and refactor the CPU flags select in
arch/m68k/cpu/mcf52x2/config.mk.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
2015-03-28 09:03:09 -04:00

230 lines
6.6 KiB
C

/*
* Configuation settings for the Motorola MC5275EVB board.
*
* By Arthur Shipkowski <art@videon-central.com>
* Copyright (C) 2005 Videon Central, Inc.
*
* Based off of M5272C3 board code by Josef Baumgartner
* <josef.baumgartner@telex.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M5275EVB_H
#define _M5275EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_M5275EVB /* define board type */
#define CONFIG_MCFTMR
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_IS_IN_FLASH 1
#else
#define CONFIG_ENV_ADDR 0xffe04000
#define CONFIG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_IS_IN_FLASH 1
#endif
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Available command configuration */
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_DHCP
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
#define CONFIG_MII 1
#define CONFIG_MII_INIT 1
#define CONFIG_SYS_DISCOVER_PHY
#define CONFIG_SYS_RX_ETH_BUFFER 8
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#define CONFIG_SYS_FEC0_PINMUX 0
#define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
#define CONFIG_SYS_FEC1_PINMUX 0
#define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC1_IOBASE
#define MCFFEC_TOUT_LOOP 50000
#define CONFIG_HAS_ETH1
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
#ifndef CONFIG_SYS_DISCOVER_PHY
#define FECDUPLEX FULL
#define FECSPEED _100BASET
#else
#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#endif
#endif
#endif
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 80000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c)
#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0)
#define CONFIG_SYS_I2C_PINMUX_SET (0x000F)
#define CONFIG_SYS_PROMPT "-> "
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if (CONFIG_CMD_KGDB)
# define CONFIG_SYS_CBSIZE 1024
#else
# define CONFIG_SYS_CBSIZE 256
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR 0x800000
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOTCOMMAND "bootm ffe40000"
#define CONFIG_SYS_MEMTEST_START 0x400
#define CONFIG_SYS_MEMTEST_END 0x380000
#ifdef CONFIG_MCFFEC
# define CONFIG_NET_RETRY_COUNT 5
# define CONFIG_OVERWRITE_ETHADDR_ONCE
#endif /* FEC_ENET */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"uboot=u-boot.bin\0" \
"load=tftp ${loadaddr} ${uboot}\0" \
"upd=run load; run prog\0" \
"prog=prot off ffe00000 ffe3ffff;" \
"era ffe00000 ffe3ffff;" \
"cp.b ${loadaddr} ffe00000 ${filesize};"\
"save\0" \
""
#define CONFIG_SYS_CLK 150000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CONFIG_SYS_MBAR 0x40000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_MONITOR_BASE 0x20000
#else
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#endif
#define CONFIG_SYS_MONITOR_LEN 0x20000
#define CONFIG_SYS_MALLOC_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
#define CONFIG_SYS_FLASH_CFI 1
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_SIZE 0x200000
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
CF_CACR_DISD | CF_CACR_INVI | \
CF_CACR_CEIB | CF_CACR_DCM | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
#define CONFIG_SYS_CS0_BASE 0xffe00000
#define CONFIG_SYS_CS0_CTRL 0x00001980
#define CONFIG_SYS_CS0_MASK 0x001F0001
#define CONFIG_SYS_CS1_BASE 0x30000000
#define CONFIG_SYS_CS1_CTRL 0x00001900
#define CONFIG_SYS_CS1_MASK 0x00070001
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CONFIG_SYS_FECI2C 0x0FA0
#endif /* _M5275EVB_H */