mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-27 15:12:21 +00:00
306881a0bf
This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
435 lines
14 KiB
C
435 lines
14 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2013 Keymile AG
|
|
* Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#if defined(CONFIG_KMCOGE4)
|
|
#define CONFIG_HOSTNAME "kmcoge4"
|
|
|
|
#else
|
|
#error ("Board not supported")
|
|
#endif
|
|
|
|
#define CONFIG_KMP204X
|
|
|
|
/* an additionnal option is required for UBI as subpage access is
|
|
* supported in u-boot
|
|
*/
|
|
#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
|
|
|
|
#define CONFIG_NAND_ECC_BCH
|
|
|
|
/* common KM defines */
|
|
#include "km/keymile-common.h"
|
|
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#define CONFIG_RAMBOOT_PBL
|
|
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
|
|
#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
|
|
#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
|
|
#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
|
|
|
|
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
|
|
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
|
|
#define CONFIG_PCIE1 /* PCIE controller 1 */
|
|
#define CONFIG_PCIE3 /* PCIE controller 3 */
|
|
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
|
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
|
|
|
#define CONFIG_SYS_DPAA_RMAN /* RMan */
|
|
|
|
/* Environment in SPI Flash */
|
|
#define CONFIG_ENV_TOTAL_SIZE 0x020000
|
|
|
|
#ifndef __ASSEMBLY__
|
|
unsigned long get_board_sys_clk(unsigned long dummy);
|
|
#endif
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
|
|
|
|
/*
|
|
* These can be toggled for performance analysis, otherwise use default.
|
|
*/
|
|
#define CONFIG_SYS_CACHE_STASHING
|
|
#define CONFIG_BACKSIDE_L2_CACHE
|
|
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
|
|
#define CONFIG_BTB /* toggle branch predition */
|
|
|
|
#define CONFIG_ENABLE_36BIT_PHYS
|
|
|
|
#define CONFIG_ADDR_MAP
|
|
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
|
|
|
|
#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
|
|
|
|
/*
|
|
* Config the L3 Cache as L3 SRAM
|
|
*/
|
|
#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
|
|
#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
|
|
CONFIG_RAMBOOT_TEXT_BASE)
|
|
#define CONFIG_SYS_L3_SIZE (1024 << 10)
|
|
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
|
|
|
|
#define CONFIG_SYS_DCSRBAR 0xf0000000
|
|
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_VERY_BIG_RAM
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
|
|
|
|
#define CONFIG_DDR_SPD
|
|
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
#define SPD_EEPROM_ADDRESS 0x54
|
|
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
|
|
/******************************************************************************
|
|
* (PRAM usage)
|
|
* ... -------------------------------------------------------
|
|
* ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
|
|
* ... |<------------------- pram -------------------------->|
|
|
* ... -------------------------------------------------------
|
|
* @END_OF_RAM:
|
|
* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
|
|
* @CONFIG_KM_PHRAM: address for /var
|
|
* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
|
|
* @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
|
|
*/
|
|
|
|
/* size of rootfs in RAM */
|
|
#define CONFIG_KM_ROOTFSSIZE 0x0
|
|
/* pseudo-non volatile RAM [hex] */
|
|
#define CONFIG_KM_PNVRAM 0x80000
|
|
/* physical RAM MTD size [hex] */
|
|
#define CONFIG_KM_PHRAM 0x100000
|
|
/* reserved pram area at the end of memory [hex]
|
|
* u-boot reserves some memory for the MP boot page
|
|
*/
|
|
#define CONFIG_KM_RESERVED_PRAM 0x1000
|
|
/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
|
|
* is not valid yet, which is the case for when u-boot copies itself to RAM
|
|
*/
|
|
#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM) >> 10)
|
|
|
|
#define CONFIG_KM_CRAMFS_ADDR 0x2000000
|
|
#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
|
|
#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
|
|
|
|
/*
|
|
* Local Bus Definitions
|
|
*/
|
|
|
|
/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
|
|
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
|
|
|
|
/* Nand Flash */
|
|
#define CONFIG_NAND_FSL_ELBC
|
|
#define CONFIG_SYS_NAND_BASE 0xffa00000
|
|
#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
|
|
|
|
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
|
|
|
/* NAND flash config */
|
|
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
|
| BR_PS_8 /* Port Size = 8 bit */ \
|
|
| BR_MS_FCM /* MSEL = FCM */ \
|
|
| BR_V) /* valid */
|
|
|
|
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
|
|
| OR_FCM_BCTLD /* LBCTL not ass */ \
|
|
| OR_FCM_SCY_1 /* 1 clk wait cycle */ \
|
|
| OR_FCM_RST /* 1 clk read setup */ \
|
|
| OR_FCM_PGS /* Large page size */ \
|
|
| OR_FCM_CST) /* 0.25 command setup */
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
|
|
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
|
|
|
|
/* QRIO FPGA */
|
|
#define CONFIG_SYS_QRIO_BASE 0xfb000000
|
|
#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
|
|
|
|
#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
|
|
| BR_PS_8 /* Port Size 8 bits */ \
|
|
| BR_DECC_OFF /* no error corr */ \
|
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
|
| BR_V) /* valid */
|
|
|
|
#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
|
|
| OR_GPCM_BCTLD /* no LCTL assert */ \
|
|
| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
|
|
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
|
|
| OR_GPCM_TRLX /* relaxed tmgs */ \
|
|
| OR_GPCM_EAD) /* extra bus clk cycles */
|
|
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
|
|
|
|
#define CONFIG_MISC_INIT_F
|
|
|
|
#define CONFIG_HWCONFIG
|
|
|
|
/* define to use L1 as initial stack */
|
|
#define CONFIG_L1_INIT_RAM
|
|
#define CONFIG_SYS_INIT_RAM_LOCK
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
|
|
/* The assembler doesn't like typecast */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
|
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
|
|
|
|
/* Serial Port - controlled on board with jumper J8
|
|
* open - index 2
|
|
* shorted - index 1
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x11C500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x11C600)
|
|
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x11D500)
|
|
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x11D600)
|
|
|
|
#define CONFIG_KM_CONSOLE_TTY "ttyS0"
|
|
|
|
/* I2C */
|
|
/* QRIO GPIOs used for deblocking */
|
|
#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
|
|
#define KM_I2C_DEBLOCK_SCL 20
|
|
#define KM_I2C_DEBLOCK_SDA 21
|
|
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_INIT_BOARD
|
|
#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
|
|
#define CONFIG_SYS_NUM_I2C_BUSES 3
|
|
#define CONFIG_SYS_I2C_MAX_HOPS 1
|
|
#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_I2C_CMD_TREE
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
|
|
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
|
|
}
|
|
#ifndef __ASSEMBLY__
|
|
void set_sda(int state);
|
|
void set_scl(int state);
|
|
int get_sda(void);
|
|
int get_scl(void);
|
|
#endif
|
|
|
|
#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
|
|
|
|
/*
|
|
* eSPI - Enhanced SPI
|
|
*/
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
*/
|
|
|
|
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
|
|
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
|
|
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
|
|
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
|
|
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
|
|
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
|
|
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
|
|
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* Qman/Bman */
|
|
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
|
|
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
|
|
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
|
|
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
|
|
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
|
|
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
|
|
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
|
|
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
|
|
CONFIG_SYS_BMAN_CENA_SIZE)
|
|
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
|
|
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
|
|
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
|
|
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
|
|
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
|
|
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
|
|
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
|
|
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
|
|
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
|
|
CONFIG_SYS_QMAN_CENA_SIZE)
|
|
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
|
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
|
|
|
|
#define CONFIG_SYS_DPAA_FMAN
|
|
#define CONFIG_SYS_DPAA_PME
|
|
/* Default address of microcode for the Linux Fman driver
|
|
* env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
|
|
* ucode is stored after env, so we got 0x120000.
|
|
*/
|
|
#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
|
|
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
|
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
|
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
|
|
/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
|
|
#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
|
|
#define CONFIG_SYS_TBIPA_VALUE 8
|
|
#define CONFIG_ETHPRIME "FM1@DTSEC5"
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
|
|
|
/*
|
|
* Hardware Watchdog
|
|
*/
|
|
#define CONFIG_WATCHDOG /* enable CPU watchdog */
|
|
#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
|
|
#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
|
|
|
|
/*
|
|
* additionnal command line configuration.
|
|
*/
|
|
|
|
/* we don't need flash support */
|
|
#undef CONFIG_JFFS2_CMDLINE
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 64 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
#ifdef CONFIG_CMD_KGDB
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#endif
|
|
|
|
#define __USB_PHY_TYPE utmi
|
|
#define CONFIG_USB_EHCI_FSL
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
|
|
#define CONFIG_KM_DEF_ENV "km-common=empty\0"
|
|
#endif
|
|
|
|
/* architecture specific default bootargs */
|
|
#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
|
|
|
|
/* FIXME: FDT_ADDR is unspecified */
|
|
#define CONFIG_KM_DEF_ENV_CPU \
|
|
"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
|
|
"cramfsloadfdt=" \
|
|
"cramfsload ${fdt_addr_r} " \
|
|
"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
|
|
"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
|
|
"u-boot=" CONFIG_HOSTNAME "/u-boot.pbl\0" \
|
|
"update=" \
|
|
"sf probe 0;sf erase 0 +${filesize};" \
|
|
"sf write ${load_addr_r} 0 ${filesize};\0" \
|
|
"set_fdthigh=true\0" \
|
|
"checkfdt=true\0" \
|
|
""
|
|
|
|
#define CONFIG_HW_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
|
|
"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
|
|
"usb_dr_mode=host\0"
|
|
|
|
#define CONFIG_KM_NEW_ENV \
|
|
"newenv=sf probe 0;" \
|
|
"sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
|
|
__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
|
|
|
|
/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
|
|
#ifndef CONFIG_KM_DEF_ARCH
|
|
#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
|
|
#endif
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
CONFIG_KM_DEF_ENV \
|
|
CONFIG_KM_DEF_ARCH \
|
|
CONFIG_KM_NEW_ENV \
|
|
CONFIG_HW_ENV_SETTINGS \
|
|
"EEprom_ivm=pca9547:70:9\0" \
|
|
""
|
|
|
|
/* App2 Local bus */
|
|
#define CONFIG_SYS_LBAPP2_BASE 0xE0000000
|
|
#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull
|
|
|
|
#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \
|
|
| BR_PS_8 /* Port Size 8 bits */ \
|
|
| BR_DECC_OFF /* no error corr */ \
|
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
|
| BR_V) /* valid */
|
|
|
|
#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
|
|
| OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
|
|
| OR_GPCM_CSNT /* LCS 1/4 clk before */ \
|
|
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
|
|
| OR_GPCM_TRLX /* relaxed tmgs */ \
|
|
| OR_GPCM_EAD) /* extra bus clk cycles */
|
|
/* Local bus app2 Base Address */
|
|
#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM
|
|
/* Local bus app2 Options */
|
|
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM
|
|
|
|
#endif /* __CONFIG_H */
|