mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 19:23:07 +00:00
d8fa0a7668
Currently Makefile produces final mpc85xx image when SPL is not used in custom file u-boot-with-dtb.bin. It is quite confusing name as build process produce also intermediate file standard file u-boot-dtb.bin (which is just intermediate and not bootable). Other platforms use u-boot.bin (UBOOT_BIN) as standard name for final bootable raw image. So change Makefile rules and binman to produce final bootable file for mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not define default rule for u-boot.bin then instruct binman (via DTS file) to store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and finally rename target u-boot-with-dtb.bin to u-boot.bin. With this change are also removed custom Makefile hacks for mpc85xx that it produced non-standard output file. And also updated documentation. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Behún <kabel@kernel.org> |
||
---|---|---|
.. | ||
cpld.c | ||
cpld.h | ||
ddr.c | ||
eth.c | ||
Kconfig | ||
MAINTAINERS | ||
Makefile | ||
p2041rdb.c | ||
pbi.cfg | ||
rcw_p2041rdb.cfg | ||
README |
Overview ========= The P2041 Processor combines four Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral bus interfaces required for networking, telecom/datacom, wireless infrastructure, and military/aerospace applications. P2041RDB board is a quad core platform supporting the P2041 processor of QorIQ DPAA series. Boot from NOR flash =================== 1. Build image make P2041RDB_config make all 2. Program image => tftp 1000000 u-boot.bin => protect off all => erase eff40000 efffffff => cp.b 1000000 eff40000 c0000 3. Program RCW => tftp 1000000 rcw.bin => protect off all => erase e8000000 e801ffff => cp.b 1000000 e8000000 50 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => protect off all => erase eff00000 eff3ffff => cp.b 1000000 eff00000 2000 5. Change DIP-switch SW1[1-5] = 10110 Note: 1 stands for 'on', 0 stands for 'off' Boot from SDCard =================== 1. Build image make P2041RDB_SDCARD_config make all 2. Generate PBL imge Use PE tool to produce a image used to be programed to SDCard which contains RCW and U-Boot image. 3. Program the PBL image to SDCard => tftp 1000000 pbl_sd.bin => mmcinfo => mmc write 1000000 8 672 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => mmc write 1000000 690 10 5. Change DIP-switch SW1[1-5] = 01100 Note: 1 stands for 'on', 0 stands for 'off' Boot from SPI flash =================== 1. Build image make P2041RDB_SPIFLASH_config make all 2. Generate PBL imge Use PE tool to produce a image used to be programed to SPI flash which contains RCW and U-Boot image. 3. Program the PBL image to SPI flash => tftp 1000000 pbl_spi.bin => spi probe 0 => sf erase 0 100000 => sf write 1000000 0 $filesize 4. Program FMAN Firmware ucode => tftp 1000000 ucode.bin => sf erase 110000 10000 => sf write 1000000 110000 $filesize 5. Change DIP-switch SW1[1-5] = 10100 Note: 1 stands for 'on', 0 stands for 'off' Device tree support and how to enable it for different configs -------------------------------------------------------------- Device tree support is available for p2041rdb for below mentioned boot, 1. NOR Boot 2. NAND Boot 3. SD Boot 4. SPIFLASH Boot To enable device tree support for other boot, below configs need to be enabled in relative defconfig file, 1. CONFIG_DEFAULT_DEVICE_TREE="p2041rdb" (Change default device tree name if required) 2. CONFIG_OF_CONTROL 3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at CONFIG_RESET_VECTOR_ADDRESS - 0xffc CPLD command ============ The CPLD is used to control the power sequence and some serdes lane mux function. cpld reset - hard reset to default bank cpld reset altbank - reset to alternate bank cpld lane_mux <lane> <mux_value> - set multiplexed lane pin lane 6: 0 -> slot1 (Default) 1 -> SGMII lane a: 0 -> slot2 (Default) 1 -> AURORA lane c: 0 -> slot2 (Default) 1 -> SATA0 lane d: 0 -> slot2 (Default) 1 -> SATA1 Using the Device Tree Source File ================================= To create the DTB (Device Tree Binary) image file, use a command similar to this: dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb Or use the following command: {linux-2.6}/make p2041rdb.dtb ARCH=powerpc then the dtb file will be generated under the following directory: {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb Booting Linux ============= Place a linux uImage in the TFTP disk area. tftp 1000000 uImage tftp 2000000 rootfs.ext2.gz.uboot tftp 3000000 p2041rdb.dtb bootm 1000000 2000000 3000000