mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-28 07:31:15 +00:00
95a372b836
This file documents when to build for da850evm and when to build for da850_am18xxevm. It also documents how to write the u-boot.ais file to persistent storage (such as SPI), in some cases as well as how to write a recovery image. Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
68 lines
2.6 KiB
Text
68 lines
2.6 KiB
Text
Summary
|
|
=======
|
|
The README is for the boot procedure used for various DA850 (or compatible
|
|
parts such as the AM1808) based boards.
|
|
|
|
In the context of U-Boot, the board is booted in three stages. The initial
|
|
bootloader which executes upon reset is the ROM Boot Loader (RBL) and sits
|
|
in the internal ROM. The RBL initializes the internal memory and then
|
|
depending on the exact board and pin configurations will initialize another
|
|
controller (such as SPI or NAND) to continue the boot process by loading
|
|
the secondary program loader (SPL). The SPL will initialize the system
|
|
further (some clocks, SDRAM) and then load the full u-boot from a
|
|
predefined location in persistent storage to DDR and jumps to the u-boot
|
|
entry point.
|
|
|
|
AIS is an image format defined by TI for the images that are to be loaded
|
|
to memory by the RBL. The image is divided into a series of sections and
|
|
the image's entry point is specified. Each section comes with meta data
|
|
like the target address the section is to be copied to and the size of the
|
|
section, which is used by the RBL to load the image. At the end of the
|
|
image the RBL jumps to the image entry point. The AIS format allows for
|
|
other things such as programming the clocks and SDRAM if the header is
|
|
programmed for it. We do not take advantage of this and instead use SPL as
|
|
it allows for additional flexibility (run-time detect of board revision,
|
|
loading the next image from a different media, etc).
|
|
|
|
|
|
Compilation
|
|
===========
|
|
The exact build target you need will depend on the board you have. For
|
|
Logic PD boards, or other boards which store the ethernet MAC address at
|
|
the end of SPI flash, run 'make da850evm'. For boards which store the
|
|
ethernet MAC address in the i2c EEPROM located at 0x50, run
|
|
'make da850_am18xxevm'. Once this build completes you will have a
|
|
u-boot.ais file that needs to be written to the correct persistent
|
|
storage.
|
|
|
|
|
|
Flashing the images to SPI
|
|
==========================
|
|
The AIS image can be written to SPI flash using the following commands.
|
|
Assuming that the network is configured and enabled and the u-boot.ais file
|
|
is tftp'able.
|
|
|
|
U-Boot > sf probe 0
|
|
U-Boot > sf erase 0 +320000
|
|
U-Boot > tftp u-boot.ais
|
|
U-Boot > sf write c0700000 0 $filesize
|
|
|
|
|
|
Recovery
|
|
========
|
|
|
|
In the case of a "bricked" board, you need to use the TI tools found
|
|
here[1] to write the u-boot.ais file. An example of recovering to the SPI
|
|
flash of an AM1808 would be:
|
|
|
|
$ mono sfh_OMAP-L138.exe -targetType AM1808 -p /dev/ttyUSB0 \
|
|
-flash_noubl /path/to/u-boot.ais
|
|
|
|
For other target types and flash locations:
|
|
|
|
$ mono sfh_OMAP-L138.exe -h
|
|
|
|
Links
|
|
=====
|
|
[1]
|
|
http://processors.wiki.ti.com/index.php/Serial_Boot_and_Flash_Loading_Utility_for_OMAP-L138
|