u-boot/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
Andre Przywara 85da558762 sunxi: dts: Update RGMII phy-mode properties
Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.

Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.

This fixes Ethernet operation on the affected boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
2022-03-26 00:16:44 +00:00

140 lines
2.5 KiB
Text

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2016 ARM Ltd.
// Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
/dts-v1/;
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero Plus";
compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5";
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
aliases {
ethernet0 = &emac;
ethernet1 = &rtl8189ftv;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
led-0 {
label = "orangepi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
default-state = "on";
};
led-1 {
label = "orangepi:red:status";
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
};
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <&reg_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii-id";
status = "okay";
};
&external_mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
non-removable;
status = "okay";
/*
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
rtl8189ftv: sdio_wifi@1 {
reg = <1>;
};
};
&spi0 {
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mxicy,mx25l1606e", "winbond,w25q128";
reg = <0>;
spi-max-frequency = <40000000>;
};
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
&usb_otg {
dr_mode = "peripheral";
status = "okay";
};
&usbphy {
/* USB Type-A ports' VBUS is always on */
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
status = "okay";
};