u-boot/board/logicpd/imx6/imx6logic.c
Adam Ford 43db8e3e41 ARM: imx6q_logic: Remove legacy pinmuxing code from board file.
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.

This patch removes the legacy pinmuxing code from the board file.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13 22:49:11 +02:00

301 lines
7.6 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 Logic PD, Inc.
*
* Author: Adam Ford <aford173@gmail.com>
*
* Based on SabreSD by Fabio Estevam <fabio.estevam@nxp.com>
* and updates by Jagan Teki <jagan@amarulasolutions.com>
*/
#include <common.h>
#include <env.h>
#include <miiphy.h>
#include <input.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <linux/sizes.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/iomux-v3.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define NAND_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
static iomux_v3_cfg_t const nand_pads[] = {
MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
};
static void setup_nand_pins(void)
{
imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
}
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
/* To enable AR8031 output a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
ar8031_phy_fixup(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
int board_early_init_f(void)
{
setup_nand_pins();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
return 0;
}
int board_late_init(void)
{
env_set("board_name", "imx6logic");
if (is_mx6dq()) {
env_set("board_rev", "MX6DQ");
if (!env_get("fdt_file"))
env_set("fdt_file", "imx6q-logicpd.dtb");
}
return 0;
}
#ifdef CONFIG_SPL_BUILD
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6q-ddr.h>
#include <spl.h>
#include <linux/libfdt.h>
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
/* break into full u-boot on 'c' */
if (serial_tstc() && serial_getc() == 'c')
return 1;
return 0;
}
#endif
void board_boot_order(u32 *spl_boot_list)
{
struct src *psrc = (struct src *)SRC_BASE_ADDR;
unsigned int reg = readl(&psrc->sbmr1) >> 11;
/*
* Upon reading BOOT_CFG register the following map is done:
* Bit 11 and 12 of BOOT_CFG register can determine the current
* mmc port
* 0x1 SD1-SOM
* 0x2 SD2-Baseboard
*/
reg &= 0x3; /* Only care about bottom 2 bits */
switch (reg) {
case 0:
spl_boot_list[0] = BOOT_DEVICE_MMC1;
break;
case 1:
spl_boot_list[0] = BOOT_DEVICE_MMC2;
break;
}
/* If we cannot find a valid MMC/SD card, try NAND */
spl_boot_list[1] = BOOT_DEVICE_NAND;
/* As a last resort, use serial downloader */
spl_boot_list[2] = BOOT_DEVICE_BOARD;
}
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0xFFFFF300, &ccm->CCGR4);
writel(0x0F0000F3, &ccm->CCGR5);
writel(0x00000FFF, &ccm->CCGR6);
}
static int mx6q_dcd_table[] = {
MX6_IOM_GRP_DDR_TYPE, 0x000C0000,
MX6_IOM_GRP_DDRPKE, 0x00000000,
MX6_IOM_DRAM_SDCLK_0, 0x00000030,
MX6_IOM_DRAM_SDCLK_1, 0x00000030,
MX6_IOM_DRAM_CAS, 0x00000030,
MX6_IOM_DRAM_RAS, 0x00000030,
MX6_IOM_GRP_ADDDS, 0x00000030,
MX6_IOM_DRAM_RESET, 0x00000030,
MX6_IOM_DRAM_SDBA2, 0x00000000,
MX6_IOM_DRAM_SDODT0, 0x00000030,
MX6_IOM_DRAM_SDODT1, 0x00000030,
MX6_IOM_GRP_CTLDS, 0x00000030,
MX6_IOM_DDRMODE_CTL, 0x00020000,
MX6_IOM_DRAM_SDQS0, 0x00000030,
MX6_IOM_DRAM_SDQS1, 0x00000030,
MX6_IOM_DRAM_SDQS2, 0x00000030,
MX6_IOM_DRAM_SDQS3, 0x00000030,
MX6_IOM_GRP_DDRMODE, 0x00020000,
MX6_IOM_GRP_B0DS, 0x00000030,
MX6_IOM_GRP_B1DS, 0x00000030,
MX6_IOM_GRP_B2DS, 0x00000030,
MX6_IOM_GRP_B3DS, 0x00000030,
MX6_IOM_DRAM_DQM0, 0x00000030,
MX6_IOM_DRAM_DQM1, 0x00000030,
MX6_IOM_DRAM_DQM2, 0x00000030,
MX6_IOM_DRAM_DQM3, 0x00000030,
MX6_MMDC_P0_MDSCR, 0x00008000,
MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003,
MX6_MMDC_P0_MPWLDECTRL0, 0x002D003A,
MX6_MMDC_P0_MPWLDECTRL1, 0x0038002B,
MX6_MMDC_P0_MPDGCTRL0, 0x03340338,
MX6_MMDC_P0_MPDGCTRL1, 0x0334032C,
MX6_MMDC_P0_MPRDDLCTL, 0x4036383C,
MX6_MMDC_P0_MPWRDLCTL, 0x2E384038,
MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333,
MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333,
MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333,
MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333,
MX6_MMDC_P0_MPMUR0, 0x00000800,
MX6_MMDC_P0_MDPDC, 0x00020036,
MX6_MMDC_P0_MDOTC, 0x09444040,
MX6_MMDC_P0_MDCFG0, 0xB8BE7955,
MX6_MMDC_P0_MDCFG1, 0xFF328F64,
MX6_MMDC_P0_MDCFG2, 0x01FF00DB,
MX6_MMDC_P0_MDMISC, 0x00011740,
MX6_MMDC_P0_MDSCR, 0x00008000,
MX6_MMDC_P0_MDRWD, 0x000026D2,
MX6_MMDC_P0_MDOR, 0x00BE1023,
MX6_MMDC_P0_MDASP, 0x00000047,
MX6_MMDC_P0_MDCTL, 0x85190000,
MX6_MMDC_P0_MDSCR, 0x00888032,
MX6_MMDC_P0_MDSCR, 0x00008033,
MX6_MMDC_P0_MDSCR, 0x00008031,
MX6_MMDC_P0_MDSCR, 0x19408030,
MX6_MMDC_P0_MDSCR, 0x04008040,
MX6_MMDC_P0_MDREF, 0x00007800,
MX6_MMDC_P0_MPODTCTRL, 0x00000007,
MX6_MMDC_P0_MDPDC, 0x00025576,
MX6_MMDC_P0_MAPSR, 0x00011006,
MX6_MMDC_P0_MDSCR, 0x00000000,
/* enable AXI cache for VDOA/VPU/IPU */
MX6_IOMUXC_GPR4, 0xF00000CF,
/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
MX6_IOMUXC_GPR6, 0x007F007F,
MX6_IOMUXC_GPR7, 0x007F007F,
};
static void ddr_init(int *table, int size)
{
int i;
for (i = 0; i < size / 2 ; i++)
writel(table[2 * i + 1], table[2 * i]);
}
static void spl_dram_init(void)
{
if (is_mx6dq())
ddr_init(mx6q_dcd_table, ARRAY_SIZE(mx6q_dcd_table));
}
void board_init_f(ulong dummy)
{
/* DDR initialization */
spl_dram_init();
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
gpr_init();
/* iomux and setup of uart and NAND pins */
board_early_init_f();
/* setup GP timer */
timer_init();
/* Enable device tree and early DM support*/
spl_early_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
}
#endif