mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 19:23:07 +00:00
9b5f9aeb3b
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
103 lines
2.8 KiB
C
103 lines
2.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0-or-later */
|
|
/*
|
|
* Copyright 2022 Toradex
|
|
*/
|
|
|
|
#ifndef __VERDIN_IMX8MP_H
|
|
#define __VERDIN_IMX8MP_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <linux/sizes.h>
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN SZ_512K
|
|
#define CONFIG_SYS_UBOOT_BASE \
|
|
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
|
|
#define CONFIG_SPL_STACK 0x960000
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x0098fc00
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K
|
|
|
|
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
|
|
#define CONFIG_MALLOC_F_ADDR 0x184000
|
|
/* For RAW image gives a error info not panic */
|
|
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
|
|
|
|
#define CONFIG_POWER_PCA9450
|
|
|
|
#define CONFIG_SYS_I2C
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
/* ENET Config */
|
|
/* ENET1 */
|
|
#if defined(CONFIG_CMD_NET)
|
|
#define CONFIG_FEC_MXC_PHYADDR 7
|
|
|
|
#define PHY_ANEG_TIMEOUT 20000
|
|
#endif /* CONFIG_CMD_NET */
|
|
|
|
#define MEM_LAYOUT_ENV_SETTINGS \
|
|
"fdt_addr_r=0x43000000\0" \
|
|
"kernel_addr_r=0x40000000\0" \
|
|
"ramdisk_addr_r=0x46400000\0" \
|
|
"scriptaddr=0x46000000\0"
|
|
|
|
/* Enable Distro Boot */
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 1) \
|
|
func(MMC, mmc, 2) \
|
|
func(DHCP, dhcp, na)
|
|
#include <config_distro_bootcmd.h>
|
|
#else
|
|
#define BOOTENV
|
|
#endif
|
|
|
|
#if defined(CONFIG_TDX_EASY_INSTALLER)
|
|
# define BOOT_SCRIPT "boot-tezi.scr"
|
|
#else
|
|
# define BOOT_SCRIPT "boot.scr"
|
|
#endif
|
|
|
|
/* Initial environment variables */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
BOOTENV \
|
|
MEM_LAYOUT_ENV_SETTINGS \
|
|
"bootcmd_mfg=fastboot 0\0" \
|
|
"boot_file=Image\0" \
|
|
"boot_scripts=" BOOT_SCRIPT "\0" \
|
|
"boot_script_dhcp=" BOOT_SCRIPT "\0" \
|
|
"console=ttymxc2\0" \
|
|
"fdt_board=dev\0" \
|
|
"initrd_addr=0x43800000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"setup=setenv setupargs console=${console},${baudrate} console=tty1 " \
|
|
"consoleblank=0 earlycon\0" \
|
|
"update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
|
|
"if test \"$confirm\" = \"y\"; then " \
|
|
"setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
|
|
"${blkcnt} / 0x200; mmc dev 2 1; mmc write ${loadaddr} 0x0 " \
|
|
"${blkcnt}; fi\0"
|
|
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
|
|
#define CONFIG_SYS_INIT_RAM_SIZE SZ_512K
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
#define CONFIG_SYS_BOOTM_LEN SZ_64M /* Increase max gunzip size */
|
|
|
|
/* i.MX 8M Plus supports max. 8GB memory in two albeit concecutive banks */
|
|
#define CONFIG_SYS_SDRAM_BASE 0x40000000
|
|
#define PHYS_SDRAM 0x40000000
|
|
#define PHYS_SDRAM_SIZE (SZ_2G + SZ_1G)
|
|
#define PHYS_SDRAM_2 0x100000000
|
|
#define PHYS_SDRAM_2_SIZE (SZ_4G + SZ_1G)
|
|
|
|
/* UART */
|
|
#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(3)
|
|
|
|
#endif /* __VERDIN_IMX8MP_H */
|