u-boot/include/configs/imx8mp_rsb3720.h
Tom Rini 9b5f9aeb3b Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BSS_MAX_SIZE
   CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:10 -04:00

191 lines
5.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2019 NXP
* Copyright 2022 Linaro
*/
#ifndef __IMX8MP_RSB3720_H
#define __IMX8MP_RSB3720_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#include <config_distro_bootcmd.h>
#define CONFIG_SYS_BOOTM_LEN (32 * SZ_1M)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_UBOOT_BASE (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
/* GUIDs for capsule updatable firmware images */
#define IMX8MP_RSB3720A1_4G_FIT_IMAGE_GUID \
EFI_GUID(0xb1251e89, 0x384a, 0x4635, 0xa8, 0x06, \
0x3a, 0xa0, 0xb0, 0xe9, 0xf9, 0x65)
#define IMX8MP_RSB3720A1_6G_FIT_IMAGE_GUID \
EFI_GUID(0xb5fb6f08, 0xe142, 0x4db1, 0x97, 0xea, \
0x5f, 0xd3, 0x6b, 0x9b, 0xe5, 0xb9)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK 0x960000
#define CONFIG_SPL_BSS_START_ADDR 0x0098FC00
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K /* 512 KB */
#define CONFIG_MALLOC_F_ADDR 0x184000 /* malloc f used before \
* GD_FLG_FULL_MALLOC_INIT \
* set \
*/
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#if defined(CONFIG_NAND_BOOT)
#define CONFIG_SPL_NAND_MXS
#endif
#endif
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_FEC_MXC_PHYADDR 4
#define DWC_NET_PHYADDR 4
#ifdef CONFIG_DWC_ETH_QOS
#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M) /* 1M */
#endif
#define PHY_ANEG_TIMEOUT 20000
#endif
#if CONFIG_IS_ENABLED(CMD_MMC)
# define BOOT_TARGET_MMC(func) \
func(MMC, mmc, 2) \
func(MMC, mmc, 1)
#else
# define BOOT_TARGET_MMC(func)
#endif
#if CONFIG_IS_ENABLED(CMD_PXE)
# define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
#else
# define BOOT_TARGET_PXE(func)
#endif
#if CONFIG_IS_ENABLED(CMD_DHCP)
# define BOOT_TARGET_DHCP(func) func(DHCP, dhcp, na)
#else
# define BOOT_TARGET_DHCP(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_MMC(func) \
BOOT_TARGET_PXE(func) \
BOOT_TARGET_DHCP(func)
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
BOOTENV \
"script=boot.scr\0" \
"image=Image\0" \
"splashimage=0x50000000\0" \
"console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200\0" \
"fdt_addr=0x43000000\0" \
"fdt_addr_r=0x43000000\0" \
"boot_fit=no\0" \
"dfu_alt_info=mmc 2=flash-bin raw 0 0x1B00 mmcpart 1\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"initrd_addr=0x43800000\0" \
"bootm_size=0x10000000\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=1\0" \
"mmcroot=/dev/mmcblk1p2 rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs ${jh_clk} console=${console} root=${mmcroot}\0 " \
"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"kernel_addr_r=0x40480000\0" \
"pxefile_addr_r=0x40480000\0" \
"ramdisk_addr_r=0x43800000\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
"bootm ${loadaddr}; " \
"else " \
"if run loadfdt; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi;\0" \
"netargs=setenv bootargs ${jh_clk} console=${console} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${loadaddr} ${image}; " \
"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
"bootm ${loadaddr}; " \
"else " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi;\0"
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* Totally 6GB or 4G DDR */
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#if defined(CONFIG_TARGET_IMX8MP_RSB3720A1_6G)
#define PHYS_SDRAM_SIZE 0xC0000000 /* 3 GB */
#define PHYS_SDRAM_2 0x100000000
#define PHYS_SDRAM_2_SIZE 0xC0000000 /* 3 GB */
#elif defined(CONFIG_TARGET_IMX8MP_RSB3720A1_4G)
#define PHYS_SDRAM_SIZE 0x80000000 /* 2 GB */
#define PHYS_SDRAM_2 0xC0000000
#define PHYS_SDRAM_2_SIZE 0x80000000 /* 2 GB */
#endif
#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#ifdef CONFIG_FSL_FSPI
#define FSL_FSPI_FLASH_SIZE SZ_32M
#define FSL_FSPI_FLASH_NUM 1
#define FSPI0_BASE_ADDR 0x30bb0000
#define FSPI0_AMBA_BASE 0x0
#define CONFIG_FSPI_QUAD_SUPPORT
#define CONFIG_SYS_FSL_FSPI_AHB
#endif
#ifdef CONFIG_NAND_MXS
/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x20000000
#endif /* CONFIG_NAND_MXS */
#endif /* __IMX8MP_RSB3720_H */