mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
4444d230ac
This should make it clear that this symbol is meant to be defined by board headers. Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
151 lines
4 KiB
C
151 lines
4 KiB
C
/*
|
|
* Copyright (C) Marvell International Ltd. and its affiliates
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#ifndef __DDR3_AXP_CONFIG_H
|
|
#define __DDR3_AXP_CONFIG_H
|
|
|
|
/*
|
|
* DDR3_LOG_LEVEL Information
|
|
*
|
|
* Level 0: Provides an error code in a case of failure, RL, WL errors
|
|
* and other algorithm failure
|
|
* Level 1: Provides the D-Unit setup (SPD/Static configuration)
|
|
* Level 2: Provides the windows margin as a results of DQS centeralization
|
|
* Level 3: Provides the windows margin of each DQ as a results of DQS
|
|
* centeralization
|
|
*/
|
|
#ifdef CONFIG_DDR_LOG_LEVEL
|
|
#define DDR3_LOG_LEVEL CONFIG_DDR_LOG_LEVEL
|
|
#else
|
|
#define DDR3_LOG_LEVEL 0
|
|
#endif
|
|
|
|
#define DDR3_PBS 1
|
|
|
|
/* This flag allows the execution of SW WL/RL upon HW failure */
|
|
#define DDR3_RUN_SW_WHEN_HW_FAIL 1
|
|
|
|
/*
|
|
* General Configurations
|
|
*
|
|
* The following parameters are required for proper setup:
|
|
*
|
|
* DDR_TARGET_FABRIC - Set desired fabric configuration
|
|
* (for sample@Reset fabfreq parameter)
|
|
* DRAM_ECC - Set ECC support 1/0
|
|
* BUS_WIDTH - 64/32 bit
|
|
* CONFIG_SPD_EEPROM - Enables auto detection of DIMMs and their timing values
|
|
* DQS_CLK_ALIGNED - Set this if CLK and DQS signals are aligned on board
|
|
* MIXED_DIMM_STATIC - Mixed DIMM + On board devices support (ODT registers
|
|
* values are taken statically)
|
|
* DDR3_TRAINING_DEBUG - Debug prints of internal code
|
|
*/
|
|
#define DDR_TARGET_FABRIC 5
|
|
/* Only enable ECC if the board selects it */
|
|
#ifdef CONFIG_BOARD_ECC_SUPPORT
|
|
#define DRAM_ECC 1
|
|
#else
|
|
#define DRAM_ECC 0
|
|
#endif
|
|
|
|
#ifdef CONFIG_DDR_32BIT
|
|
#define BUS_WIDTH 32
|
|
#else
|
|
#define BUS_WIDTH 64
|
|
#endif
|
|
|
|
#undef DQS_CLK_ALIGNED
|
|
#undef MIXED_DIMM_STATIC
|
|
#define DDR3_TRAINING_DEBUG 0
|
|
#define REG_DIMM_SKIP_WL 0
|
|
|
|
/* Marvell boards specific configurations */
|
|
#if defined(DB_78X60_PCAC)
|
|
#undef CONFIG_SPD_EEPROM
|
|
#define STATIC_TRAINING
|
|
#endif
|
|
|
|
#if defined(DB_78X60_AMC)
|
|
#undef CONFIG_SPD_EEPROM
|
|
#undef DRAM_ECC
|
|
#define DRAM_ECC 1
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPD_EEPROM
|
|
/*
|
|
* DIMM support parameters:
|
|
* DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T
|
|
* DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs
|
|
* (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...)
|
|
*/
|
|
#define DRAM_2T 0x0
|
|
#define DIMM_CS_BITMAP 0xF
|
|
#define DUNIT_SPD
|
|
#endif
|
|
|
|
#ifdef DRAM_ECC
|
|
/*
|
|
* ECC support parameters:
|
|
*
|
|
* U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need
|
|
* to configure the scrubbing area
|
|
*/
|
|
#define TRAINING_SIZE 0x20000
|
|
#define U_BOOT_START_ADDR 0
|
|
#define U_BOOT_SCRUB_SIZE 0x1000000 /* TRAINING_SIZE */
|
|
#endif
|
|
|
|
/*
|
|
* Registered DIMM Support - In case registered DIMM is attached,
|
|
* please supply the following values:
|
|
* (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock
|
|
* Driver with Parity and Quad Chip
|
|
* Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications")
|
|
* RC0: Global Features Control Word
|
|
* RC1: Clock Driver Enable Control Word
|
|
* RC2: Timing Control Word
|
|
* RC3-RC5 - taken from SPD
|
|
* RC8: Additional IBT Setting Control Word
|
|
* RC9: Power Saving Settings Control Word
|
|
* RC10: Encoding for RDIMM Operating Speed
|
|
* RC11: Operating Voltage VDD and VREFCA Control Word
|
|
*/
|
|
#define RDIMM_RC0 0
|
|
#define RDIMM_RC1 0
|
|
#define RDIMM_RC2 0
|
|
#define RDIMM_RC8 0
|
|
#define RDIMM_RC9 0
|
|
#define RDIMM_RC10 0x2
|
|
#define RDIMM_RC11 0x0
|
|
|
|
#if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM)
|
|
#define DUNIT_STATIC
|
|
#endif
|
|
|
|
#if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM)
|
|
/*
|
|
* This flag allows the user to change the dram refresh cycle in ps,
|
|
* only in case of SPD or MIX DIMM topology
|
|
*/
|
|
#define TREFI_USER_EN
|
|
|
|
#ifdef TREFI_USER_EN
|
|
#define TREFI_USER 3900000
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPD_EEPROM
|
|
/*
|
|
* AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards.
|
|
* Enables I2C auto detection different options
|
|
*/
|
|
#if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \
|
|
defined(CONFIG_DB_784MP_GP)
|
|
#define AUTO_DETECTION_SUPPORT
|
|
#endif
|
|
#endif
|
|
|
|
#endif /* __DDR3_AXP_CONFIG_H */
|