mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 19:10:13 +00:00
f232950f82
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
375 lines
12 KiB
C
375 lines
12 KiB
C
/*
|
|
* (C) Copyright 2000, 2001
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
|
|
#define CONFIG_V37 1 /* ...on a Marel V37 board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x40000000
|
|
|
|
#define CONFIG_LCD
|
|
#define CONFIG_MPC8XX_LCD
|
|
#define CONFIG_SHARP_LQ084V1DG21
|
|
#undef CONFIG_LCD_LOGO
|
|
|
|
/*-----------------------------------------------------------------------------
|
|
* I2C Configuration
|
|
*-----------------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_I2C 1
|
|
#define CONFIG_SYS_I2C_SLAVE 0x2
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1
|
|
#undef CONFIG_8xx_CONS_SMC2 /* Console is on SMC2 */
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
#define CONFIG_BAUDRATE 9600 /* console baudrate = 115kbps */
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
|
|
#endif
|
|
|
|
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
|
|
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"tftpboot; " \
|
|
"setenv bootargs console=tty0 " \
|
|
"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_CMD_DATE
|
|
|
|
|
|
/*
|
|
* JFFS2 partitions
|
|
*
|
|
*/
|
|
/* No command line, one static partition, whole device */
|
|
#undef CONFIG_CMD_MTDPARTS
|
|
#define CONFIG_JFFS2_DEV "nor1"
|
|
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
|
|
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
|
|
|
|
/* mtdparts command line support */
|
|
/* Note: fake mtd_id used, no linux mtd map file */
|
|
/*
|
|
#define CONFIG_CMD_MTDPARTS
|
|
#define MTDIDS_DEFAULT "nor1=v37-1"
|
|
#define MTDPARTS_DEFAULT "mtdparts=v37-1:-(jffs2)"
|
|
*/
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xF0000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE0 0x40000000
|
|
#define CONFIG_SYS_FLASH_BASE1 0x60000000
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH_BASE1
|
|
|
|
#if defined(DEBUG)
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
|
|
#endif
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE0
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 35 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_IS_IN_NVRAM 1
|
|
#define CONFIG_ENV_ADDR 0x80000000/* Address of Environment */
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
|
|
#define CONFIG_ENV_OFFSET 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR 0xFFFFFF88
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/*%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_RTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
/*
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit
|
|
*
|
|
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
|
|
*/
|
|
/* up to 50 MHz we use a 1:1 clock */
|
|
#define CONFIG_SYS_PLPRCR ( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS )
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
/* up to 50 MHz we use a 1:1 clock */
|
|
#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCMCIA stuff
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
|
|
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
|
|
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#undef CONFIG_IDE_PCCARD /* Use IDE with PC Card Adapter */
|
|
|
|
#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0 and OR0 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
|
|
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
|
|
|
|
#define CONFIG_SYS_OR_TIMING_FLASH 0xF56
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V)
|
|
|
|
#define CONFIG_SYS_OR5_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR5_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V)
|
|
|
|
/*
|
|
* BR1 and OR1 (Battery backed SRAM)
|
|
*/
|
|
#define CONFIG_SYS_BR1_PRELIM 0x80000401
|
|
#define CONFIG_SYS_OR1_PRELIM 0xFFC00736
|
|
|
|
/*
|
|
* BR2 and OR2 (SDRAM)
|
|
*/
|
|
#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
|
|
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB */
|
|
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
|
|
#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
/* Marel V37 mem setting */
|
|
|
|
#define CONFIG_SYS_BR3_CAN 0xC0000401
|
|
#define CONFIG_SYS_OR3_CAN 0xFFFF0724
|
|
|
|
/*
|
|
#define CONFIG_SYS_BR3_PRELIM 0xFA400001
|
|
#define CONFIG_SYS_OR3_PRELIM 0xFFFF8910
|
|
#define CONFIG_SYS_BR4_PRELIM 0xFA000401
|
|
#define CONFIG_SYS_OR4_PRELIM 0xFFFE0970
|
|
*/
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*/
|
|
|
|
/* periodic timer for refresh */
|
|
#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
|
|
|
|
/*
|
|
* Refresh clock Prescalar
|
|
*/
|
|
#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV16
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 10 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \
|
|
MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
|
|
|
|
#endif /* __CONFIG_H */
|