mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-09 04:43:29 +00:00
cdb23792e8
Remove platform CONFIG_SYS_HZ definition for configs A-Z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
438 lines
16 KiB
C
438 lines
16 KiB
C
/*
|
|
* (C) Copyright 2000-2005
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
|
|
#define CONFIG_IP860 1 /* ...on a IP860 board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x10000000
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#define CONFIG_BAUDRATE 9600
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \
|
|
"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootp; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
|
|
/* enable I2C and select the hardware/software driver */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
|
|
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
|
|
#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
|
|
/*
|
|
* Software (bit-bang) I2C driver configuration
|
|
*/
|
|
#define PB_SCL 0x00000020 /* PB 26 */
|
|
#define PB_SDA 0x00000010 /* PB 27 */
|
|
|
|
#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
|
|
#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
|
|
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
|
|
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
|
|
#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
|
|
else immr->im_cpm.cp_pbdat &= ~PB_SDA
|
|
#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
|
|
else immr->im_cpm.cp_pbdat &= ~PB_SCL
|
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
|
|
# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
|
|
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
|
|
/* mask of address bits that overflow into the "EEPROM chip address" */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
|
|
|
|
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_BEDBUG
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_SNTP
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
|
|
|
|
#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xF1000000 /* Non-standard value!! */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0x10000000
|
|
#ifdef DEBUG
|
|
#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
|
|
#else
|
|
#if 0 /* need more space for I2C tests */
|
|
#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
|
#endif
|
|
#endif
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 124 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#undef CONFIG_ENV_IS_IN_FLASH
|
|
#undef CONFIG_ENV_IS_IN_NVRAM
|
|
#undef CONFIG_ENV_IS_IN_NVRAM
|
|
#undef DEBUG_I2C
|
|
#define CONFIG_ENV_IS_IN_EEPROM
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_NVRAM
|
|
#define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */
|
|
#define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */
|
|
#endif /* CONFIG_ENV_IS_IN_NVRAM */
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_EEPROM
|
|
#define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */
|
|
#define CONFIG_ENV_SIZE 1536 /* Use remaining space */
|
|
#endif /* CONFIG_ENV_IS_IN_EEPROM */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
#define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before
|
|
* running in RAM.
|
|
*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
* +0x0004
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* +0x0000 => 0x80600800
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \
|
|
SIUMCR_DBGC11 | SIUMCR_MLRC10)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Clock Setting - get clock frequency from Board Revision Register
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#ifndef __ASSEMBLY__
|
|
extern unsigned long ip860_get_clk_freq (void);
|
|
#endif
|
|
#define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq()
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
* +0x0200 => 0x00C2
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
* +0x0240 => 0x0082
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit, set PLL multiplication factor !
|
|
*/
|
|
/* +0x0286 => was: 0x0000D000 */
|
|
#define CONFIG_SYS_PLPRCR \
|
|
( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \
|
|
/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
|
|
PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
|
|
)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS | \
|
|
SCCR_RTDIV | SCCR_RTSEL | \
|
|
/*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
|
|
SCCR_EBDF00 | SCCR_DFSYNC00 | \
|
|
SCCR_DFBRG00 | SCCR_DFNL000 | \
|
|
SCCR_DFNH000)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/* +0x0220 => 0x00C3 */
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RCCR - RISC Controller Configuration Register 19-4
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/* +0x09C4 => TIMEP=1 */
|
|
#define CONFIG_SYS_RCCR 0x0100
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RMDS - RISC Microcode Development Support Control Register
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RMDS 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* DER - Debug Event Register
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*/
|
|
|
|
/*
|
|
* MAMR settings for SDRAM - 16-14
|
|
* => 0xC3804114
|
|
*/
|
|
|
|
/* periodic timer for refresh */
|
|
#define CONFIG_SYS_MAMR_PTA 0xC3
|
|
|
|
#define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
/*
|
|
* BR1 and OR1 (FLASH)
|
|
*/
|
|
#define FLASH_BASE 0x10000000 /* FLASH bank #0 */
|
|
|
|
/* used to re-map FLASH
|
|
* restrict access enough to keep SRAM working (if any)
|
|
* but not too much to meddle with FLASH accesses
|
|
*/
|
|
/* allow for max 8 MB of Flash */
|
|
#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
|
|
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
/* 16 bit, bank valid */
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_BR0_PRELIM
|
|
|
|
/*
|
|
* BR2/OR2 - SDRAM
|
|
*/
|
|
#define SDRAM_BASE 0x00000000 /* SDRAM bank */
|
|
#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
|
|
#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */
|
|
|
|
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
|
|
|
|
#define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
|
|
#define CONFIG_SYS_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
/*
|
|
* BR3/OR3 - SRAM (16 bit)
|
|
*/
|
|
#define SRAM_BASE 0x20000000
|
|
#define CONFIG_SYS_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */
|
|
#define CONFIG_SYS_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
|
|
#define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK)))
|
|
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */
|
|
#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */
|
|
#define CONFIG_SYS_SRAM_BASE SRAM_BASE
|
|
#define CONFIG_SYS_SRAM_SIZE SRAM_SIZE
|
|
|
|
/*
|
|
* BR4/OR4 - Board Control & Status (8 bit)
|
|
*/
|
|
#define BCSR_BASE 0xFC000000
|
|
#define CONFIG_SYS_OR4 0xFFFF0120 /* BI (internal) */
|
|
#define CONFIG_SYS_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
|
|
|
|
/*
|
|
* BR5/OR5 - IP Slot A/B (16 bit)
|
|
*/
|
|
#define IP_SLOT_BASE 0x40000000
|
|
#define CONFIG_SYS_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */
|
|
#define CONFIG_SYS_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
|
|
|
|
/*
|
|
* BR6/OR6 - VME STD (16 bit)
|
|
*/
|
|
#define VME_STD_BASE 0xFE000000
|
|
#define CONFIG_SYS_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */
|
|
#define CONFIG_SYS_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
|
|
|
|
/*
|
|
* BR7/OR7 - SHORT I/O + RTC + IACK (16 bit)
|
|
*/
|
|
#define VME_SHORT_BASE 0xFF000000
|
|
#define CONFIG_SYS_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */
|
|
#define CONFIG_SYS_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Board Control and Status Region:
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#ifndef __ASSEMBLY__
|
|
typedef struct ip860_bcsr_s {
|
|
unsigned char shmem_addr; /* +00 shared memory address register */
|
|
unsigned char reserved0;
|
|
unsigned char mbox_addr; /* +02 mailbox address register */
|
|
unsigned char reserved1;
|
|
unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */
|
|
unsigned char reserved2;
|
|
unsigned char vme_int_pend; /* +06 VME interrupt pending register */
|
|
unsigned char reserved3;
|
|
unsigned char bd_int_mask; /* +08 board interrupt mask register */
|
|
unsigned char reserved4;
|
|
unsigned char bd_int_pend; /* +0A board interrupt pending register */
|
|
unsigned char reserved5;
|
|
unsigned char bd_ctrl; /* +0C board control register */
|
|
unsigned char reserved6;
|
|
unsigned char bd_status; /* +0E board status register */
|
|
unsigned char reserved7;
|
|
unsigned char vme_irq; /* +10 VME interrupt request register */
|
|
unsigned char reserved8;
|
|
unsigned char vme_ivec; /* +12 VME interrupt vector register */
|
|
unsigned char reserved9;
|
|
unsigned char cli_mbox; /* +14 clear mailbox irq */
|
|
unsigned char reservedA;
|
|
unsigned char rtc; /* +16 RTC control register */
|
|
unsigned char reservedB;
|
|
unsigned char mbox_data; /* +18 mailbox read/write register */
|
|
unsigned char reservedC;
|
|
unsigned char wd_trigger; /* +1A Watchdog trigger register */
|
|
unsigned char reservedD;
|
|
unsigned char rmw_req; /* +1C RMW request register */
|
|
unsigned char reservedE;
|
|
unsigned char bd_rev; /* +1E Board Revision register */
|
|
} ip860_bcsr_t;
|
|
#endif /* __ASSEMBLY__ */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Board Control Register: bd_ctrl (Offset 0x0C)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */
|
|
#define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */
|
|
#define BD_CTRL_FLWE 0x20 /* Flash Write Enable */
|
|
#define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */
|
|
|
|
#endif /* __CONFIG_H */
|