mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-21 18:53:06 +00:00
e471ddf0f3
Move the relevant bits from ds109.{c,h} into common/ and adjust the code
to fit both DS109 and DS414. Moreover:
* Introduce syno_board_id() which translates CONFIG_MACH_TYPE into the
expected board ID tag value.
* Properly initialize isusbhost, mac and mtu fields from env variables.
* Set the right bootargs/bootcmd to correctly boot legacy kernel out of
the (DS414) box. Getting the ramdisk location right is a bit tedious.
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
149 lines
3.2 KiB
C
149 lines
3.2 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2009-2012
|
|
* Wojciech Dubowik <wojciech.dubowik@neratec.com>
|
|
* Luka Perkov <luka@openwrt.org>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include <linux/delay.h>
|
|
#include "ds109.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(DS109_OE_VAL_LOW,
|
|
DS109_OE_VAL_HIGH,
|
|
DS109_OE_LOW, DS109_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_SPI_SCn, /* SPI Flash */
|
|
MPP1_SPI_MOSI,
|
|
MPP2_SPI_SCK,
|
|
MPP3_SPI_MISO,
|
|
MPP4_GPIO,
|
|
MPP5_GPO,
|
|
MPP6_SYSRST_OUTn, /* Reset signal */
|
|
MPP7_GPO,
|
|
MPP8_TW_SDA, /* I2C */
|
|
MPP9_TW_SCK, /* I2C */
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_GPO,
|
|
MPP13_UART1_TXD,
|
|
MPP14_UART1_RXD,
|
|
MPP15_GPIO,
|
|
MPP16_GPIO,
|
|
MPP17_GPIO,
|
|
MPP18_GPO,
|
|
MPP19_GPO,
|
|
MPP20_SATA1_ACTn,
|
|
MPP21_SATA0_ACTn,
|
|
MPP22_GPIO, /* HDD2 FAIL LED */
|
|
MPP23_GPIO, /* HDD1 FAIL LED */
|
|
MPP24_GPIO,
|
|
MPP25_GPIO,
|
|
MPP26_GPIO,
|
|
MPP27_GPIO,
|
|
MPP28_GPIO,
|
|
MPP29_GPIO,
|
|
MPP30_GPIO,
|
|
MPP31_GPIO, /* HDD2 */
|
|
MPP32_GPIO, /* FAN A */
|
|
MPP33_GPIO, /* FAN B */
|
|
MPP34_GPIO, /* FAN C */
|
|
MPP35_GPIO, /* FAN SENSE */
|
|
MPP36_GPIO,
|
|
MPP37_GPIO,
|
|
MPP38_GPIO,
|
|
MPP39_GPIO,
|
|
MPP40_GPIO,
|
|
MPP41_GPIO,
|
|
MPP42_GPIO,
|
|
MPP43_GPIO,
|
|
MPP44_GPIO,
|
|
MPP45_GPIO,
|
|
MPP46_GPIO,
|
|
MPP47_GPIO,
|
|
MPP48_GPIO,
|
|
MPP49_GPIO,
|
|
0
|
|
};
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Synology reset uses UART */
|
|
#include <ns16550.h>
|
|
#define SOFTWARE_SHUTDOWN 0x31
|
|
#define SOFTWARE_REBOOT 0x43
|
|
#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE
|
|
void reset_misc(void)
|
|
{
|
|
int b_d;
|
|
printf("Synology reset...");
|
|
udelay(50000);
|
|
|
|
b_d = ns16550_calc_divisor((struct ns16550 *)CONFIG_SYS_NS16550_COM2,
|
|
CONFIG_SYS_NS16550_CLK, 9600);
|
|
ns16550_init((struct ns16550 *)CONFIG_SYS_NS16550_COM2, b_d);
|
|
ns16550_putc((struct ns16550 *)CONFIG_SYS_NS16550_COM2,
|
|
SOFTWARE_REBOOT);
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and enable MV88E1116 PHY */
|
|
void reset_phy(void)
|
|
{
|
|
u16 reg;
|
|
u16 devadr;
|
|
char *name = "egiga0";
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
|
|
printf("Error: 88E1116 could not read PHY dev address\n");
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 4.7.2 of chip datasheet
|
|
*/
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
|
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
|
|
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
|
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, devadr);
|
|
|
|
printf("88E1116 Initialized on %s\n", name);
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|