u-boot/board/freescale/mpc8641hpcn/mpc8641hpcn.c
Simon Glass 088454cde2 board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:59:20 -04:00

244 lines
4.8 KiB
C

/*
* Copyright 2006, 2007, 2010-2011 Freescale Semiconductor.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
phys_size_t fixed_sdram(void);
int checkboard(void)
{
u8 vboot;
u8 *pixis_base = (u8 *)PIXIS_BASE;
printf ("Board: MPC8641HPCN, Sys ID: 0x%02x, "
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
in_8(pixis_base + PIXIS_PVER));
vboot = in_8(pixis_base + PIXIS_VBOOT);
if (vboot & PIXIS_VBOOT_FMAP)
printf ("vBank: %d\n", ((vboot & PIXIS_VBOOT_FBANK) >> 6));
else
puts ("Promjet\n");
return 0;
}
int initdram(void)
{
phys_size_t dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
dram_size = fsl_ddr_sdram();
#else
dram_size = fixed_sdram();
#endif
setup_ddr_bat(dram_size);
debug(" DDR: ");
gd->ram_size = dram_size;
return 0;
}
#if !defined(CONFIG_SPD_EEPROM)
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
phys_size_t
fixed_sdram(void)
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
struct ccsr_ddr __iomem *ddr = &immap->im_ddr1;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
ddr->sdram_ocd_cntl = CONFIG_SYS_DDR_OCD_CTRL;
ddr->sdram_ocd_status = CONFIG_SYS_DDR_OCD_STATUS;
#if defined (CONFIG_DDR_ECC)
ddr->err_disable = 0x0000008D;
ddr->err_sbe = 0x00ff0000;
#endif
asm("sync;isync");
udelay(500);
#if defined (CONFIG_DDR_ECC)
/* Enable ECC checking */
ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
#else
ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
#endif
asm("sync; isync");
udelay(500);
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
void pci_init_board(void)
{
fsl_pcie_init_board(0);
#ifdef CONFIG_PCIE1
/*
* Activate ULI1575 legacy chip by performing a fake
* memory access. Needed to make ULI RTC work.
*/
in_be32((unsigned *) ((char *)(CONFIG_SYS_PCIE1_MEM_VIRT
+ CONFIG_SYS_PCIE1_MEM_SIZE - 0x1000000)));
#endif /* CONFIG_PCIE1 */
}
#if defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
int off;
u64 *tmp;
int addrcells;
ft_cpu_setup(blob, bd);
FT_FSL_PCI_SETUP;
/*
* Warn if it looks like the device tree doesn't match u-boot.
* This is just an estimation, based on the location of CCSR,
* which is defined by the "reg" property in the soc node.
*/
off = fdt_path_offset(blob, "/soc8641");
addrcells = fdt_address_cells(blob, 0);
tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL);
if (tmp) {
u64 addr;
if (addrcells == 1)
addr = *(u32 *)tmp;
else
addr = *tmp;
if (addr != CONFIG_SYS_CCSRBAR_PHYS)
printf("WARNING: The CCSRBAR address in your .dts "
"does not match the address of the CCSR "
"in u-boot. This means your .dts might "
"be old.\n");
}
return 0;
}
#endif
/*
* get_board_sys_clk
* Reads the FPGA on board for CONFIG_SYS_CLK_FREQ
*/
unsigned long
get_board_sys_clk(ulong dummy)
{
u8 i, go_bit, rd_clks;
ulong val = 0;
u8 *pixis_base = (u8 *)PIXIS_BASE;
go_bit = in_8(pixis_base + PIXIS_VCTL);
go_bit &= 0x01;
rd_clks = in_8(pixis_base + PIXIS_VCFGEN0);
rd_clks &= 0x1C;
/*
* Only if both go bit and the SCLK bit in VCFGEN0 are set
* should we be using the AUX register. Remember, we also set the
* GO bit to boot from the alternate bank on the on-board flash
*/
if (go_bit) {
if (rd_clks == 0x1c)
i = in_8(pixis_base + PIXIS_AUX);
else
i = in_8(pixis_base + PIXIS_SPD);
} else {
i = in_8(pixis_base + PIXIS_SPD);
}
i &= 0x07;
switch (i) {
case 0:
val = 33000000;
break;
case 1:
val = 40000000;
break;
case 2:
val = 50000000;
break;
case 3:
val = 66000000;
break;
case 4:
val = 83000000;
break;
case 5:
val = 100000000;
break;
case 6:
val = 134000000;
break;
case 7:
val = 166000000;
break;
}
return val;
}
int board_eth_init(bd_t *bis)
{
/* Initialize TSECs */
cpu_eth_init(bis);
return pci_eth_init(bis);
}
void board_reset(void)
{
u8 *pixis_base = (u8 *)PIXIS_BASE;
out_8(pixis_base + PIXIS_RST, 0);
while (1)
;
}