mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 06:04:34 +00:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
75 lines
2 KiB
C
75 lines
2 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2019 NXP
|
|
*/
|
|
|
|
#ifndef __LS1028A_RDB_H
|
|
#define __LS1028A_RDB_H
|
|
|
|
#include "ls1028a_common.h"
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 100000000
|
|
#define CONFIG_DDR_CLK_FREQ 100000000
|
|
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
|
|
|
|
#define CONFIG_SYS_RTC_BUS_NUM 0
|
|
|
|
/* Store environment at top of flash */
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
|
|
#define CONFIG_QIXIS_I2C_ACCESS
|
|
|
|
/*
|
|
* QIXIS Definitions
|
|
*/
|
|
#define CONFIG_FSL_QIXIS
|
|
|
|
#ifdef CONFIG_FSL_QIXIS
|
|
#define QIXIS_BASE 0x7fb00000
|
|
#define QIXIS_BASE_PHYS QIXIS_BASE
|
|
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
|
|
#define QIXIS_LBMAP_SWITCH 2
|
|
#define QIXIS_LBMAP_MASK 0xe0
|
|
#define QIXIS_LBMAP_SHIFT 0x5
|
|
#define QIXIS_LBMAP_DFLTBANK 0x00
|
|
#define QIXIS_LBMAP_ALTBANK 0x00
|
|
#define QIXIS_LBMAP_SD 0x00
|
|
#define QIXIS_LBMAP_EMMC 0x00
|
|
#define QIXIS_LBMAP_QSPI 0x00
|
|
#define QIXIS_RCW_SRC_SD 0xf8
|
|
#define QIXIS_RCW_SRC_EMMC 0xf9
|
|
#define QIXIS_RCW_SRC_QSPI 0xff
|
|
#define QIXIS_RST_CTL_RESET 0x31
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x10
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x11
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
#define QIXIS_RST_FORCE_MEM 0x01
|
|
|
|
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_8 | \
|
|
CSPR_MSEL_GPCM | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
|
|
CSOR_NOR_NOR_MODE_AVD_NOR | \
|
|
CSOR_NOR_TRHZ_80)
|
|
#endif
|
|
|
|
/* SATA */
|
|
#ifndef CONFIG_CMD_EXT2
|
|
#define CONFIG_CMD_EXT2
|
|
#endif
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
|
CONFIG_SYS_SCSI_MAX_LUN)
|
|
#define SCSI_VEND_ID 0x1b4b
|
|
#define SCSI_DEV_ID 0x9170
|
|
#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
|
|
#define CONFIG_SCSI_AHCI_PLAT
|
|
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
|
|
|
|
#endif /* __LS1028A_RDB_H */
|