mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
90526e9fba
Move this header out of the common header. Network support is used in quite a few places but it still does not warrant blanket inclusion. Note that this net.h header itself has quite a lot in it. It could be split into the driver-mode support, functions, structures, checksumming, etc. Signed-off-by: Simon Glass <sjg@chromium.org>
154 lines
4.1 KiB
C
154 lines
4.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/immap_85xx.h>
|
|
#include <fm_eth.h>
|
|
#include <fsl_mdio.h>
|
|
#include <malloc.h>
|
|
#include <fsl_dtsec.h>
|
|
#include <vsc9953.h>
|
|
|
|
#include "../common/fman.h"
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
#ifdef CONFIG_FMAN_ENET
|
|
struct memac_mdio_info memac_mdio_info;
|
|
unsigned int i;
|
|
int phy_addr = 0;
|
|
#ifdef CONFIG_VSC9953
|
|
phy_interface_t phy_int;
|
|
struct mii_dev *bus;
|
|
#endif
|
|
|
|
printf("Initializing Fman\n");
|
|
|
|
memac_mdio_info.regs =
|
|
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
|
|
memac_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
|
|
|
/* Register the real 1G MDIO bus */
|
|
fm_memac_mdio_init(bis, &memac_mdio_info);
|
|
|
|
/*
|
|
* Program on board RGMII, SGMII PHY addresses.
|
|
*/
|
|
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
|
|
int idx = i - FM1_DTSEC1;
|
|
|
|
switch (fm_info_get_enet_if(i)) {
|
|
#if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1040D4RDB)
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
/* T1040RDB & T1040D4RDB only supports SGMII on
|
|
* DTSEC3
|
|
*/
|
|
fm_info_set_phy_address(FM1_DTSEC3,
|
|
CONFIG_SYS_SGMII1_PHY_ADDR);
|
|
break;
|
|
#endif
|
|
#ifdef CONFIG_TARGET_T1042RDB
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
/* T1042RDB doesn't supports SGMII on DTSEC1 & DTSEC2 */
|
|
if ((FM1_DTSEC1 == i) || (FM1_DTSEC2 == i))
|
|
fm_info_set_phy_address(i, 0);
|
|
/* T1042RDB only supports SGMII on DTSEC3 */
|
|
fm_info_set_phy_address(FM1_DTSEC3,
|
|
CONFIG_SYS_SGMII1_PHY_ADDR);
|
|
break;
|
|
#endif
|
|
#ifdef CONFIG_TARGET_T1042D4RDB
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
/* T1042D4RDB supports SGMII on DTSEC1, DTSEC2
|
|
* & DTSEC3
|
|
*/
|
|
if (FM1_DTSEC1 == i)
|
|
phy_addr = CONFIG_SYS_SGMII1_PHY_ADDR;
|
|
if (FM1_DTSEC2 == i)
|
|
phy_addr = CONFIG_SYS_SGMII2_PHY_ADDR;
|
|
if (FM1_DTSEC3 == i)
|
|
phy_addr = CONFIG_SYS_SGMII3_PHY_ADDR;
|
|
fm_info_set_phy_address(i, phy_addr);
|
|
break;
|
|
#endif
|
|
case PHY_INTERFACE_MODE_RGMII:
|
|
if (FM1_DTSEC4 == i)
|
|
phy_addr = CONFIG_SYS_RGMII1_PHY_ADDR;
|
|
if (FM1_DTSEC5 == i)
|
|
phy_addr = CONFIG_SYS_RGMII2_PHY_ADDR;
|
|
fm_info_set_phy_address(i, phy_addr);
|
|
break;
|
|
case PHY_INTERFACE_MODE_QSGMII:
|
|
fm_info_set_phy_address(i, 0);
|
|
break;
|
|
case PHY_INTERFACE_MODE_NONE:
|
|
fm_info_set_phy_address(i, 0);
|
|
break;
|
|
default:
|
|
printf("Fman1: DTSEC%u set to unknown interface %i\n",
|
|
idx + 1, fm_info_get_enet_if(i));
|
|
fm_info_set_phy_address(i, 0);
|
|
break;
|
|
}
|
|
if (fm_info_get_enet_if(i) == PHY_INTERFACE_MODE_QSGMII ||
|
|
fm_info_get_enet_if(i) == PHY_INTERFACE_MODE_NONE)
|
|
fm_info_set_mdio(i, NULL);
|
|
else
|
|
fm_info_set_mdio(i,
|
|
miiphy_get_dev_by_name(
|
|
DEFAULT_FM_MDIO_NAME));
|
|
}
|
|
|
|
#ifdef CONFIG_VSC9953
|
|
/* SerDes configured for QSGMII */
|
|
if (serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_A) >= 0) {
|
|
for (i = 0; i < 4; i++) {
|
|
bus = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
|
|
phy_addr = CONFIG_SYS_FM1_QSGMII11_PHY_ADDR + i;
|
|
phy_int = PHY_INTERFACE_MODE_QSGMII;
|
|
|
|
vsc9953_port_info_set_mdio(i, bus);
|
|
vsc9953_port_info_set_phy_address(i, phy_addr);
|
|
vsc9953_port_info_set_phy_int(i, phy_int);
|
|
vsc9953_port_enable(i);
|
|
}
|
|
}
|
|
if (serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_B) >= 0) {
|
|
for (i = 4; i < 8; i++) {
|
|
bus = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
|
|
phy_addr = CONFIG_SYS_FM1_QSGMII21_PHY_ADDR + i - 4;
|
|
phy_int = PHY_INTERFACE_MODE_QSGMII;
|
|
|
|
vsc9953_port_info_set_mdio(i, bus);
|
|
vsc9953_port_info_set_phy_address(i, phy_addr);
|
|
vsc9953_port_info_set_phy_int(i, phy_int);
|
|
vsc9953_port_enable(i);
|
|
}
|
|
}
|
|
|
|
/* Connect DTSEC1 to L2 switch if it doesn't have a PHY */
|
|
if (serdes_get_first_lane(FSL_SRDS_1, SGMII_FM1_DTSEC1) < 0)
|
|
vsc9953_port_enable(8);
|
|
|
|
/* Connect DTSEC2 to L2 switch if it doesn't have a PHY */
|
|
if (serdes_get_first_lane(FSL_SRDS_1, SGMII_FM1_DTSEC2) < 0) {
|
|
/* Enable L2 On MAC2 using SCFG */
|
|
struct ccsr_scfg *scfg = (struct ccsr_scfg *)
|
|
CONFIG_SYS_MPC85xx_SCFG;
|
|
|
|
out_be32(&scfg->esgmiiselcr, in_be32(&scfg->esgmiiselcr) |
|
|
(0x80000000));
|
|
vsc9953_port_enable(9);
|
|
}
|
|
#endif
|
|
|
|
cpu_eth_init(bis);
|
|
#endif
|
|
|
|
return pci_eth_init(bis);
|
|
}
|