u-boot/board/scb9328/lowlevel_init.S
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

189 lines
3.5 KiB
ArmAsm

/*
* Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <version.h>
#include <asm/arch/imx-regs.h>
.globl lowlevel_init
lowlevel_init:
mov r10, lr
/* Change PERCLK1DIV to 14 ie 14+1 */
ldr r0, =PCDR
ldr r1, =CONFIG_SYS_PCDR_VAL
str r1, [r0]
/* set MCU PLL Control Register 0 */
ldr r0, =MPCTL0
ldr r1, =CONFIG_SYS_MPCTL0_VAL
str r1, [r0]
/* set mpll restart bit */
ldr r0, =CSCR
ldr r1, [r0]
orr r1,r1,#(1<<21)
str r1, [r0]
mov r2,#0x10
1:
mov r3,#0x2000
2:
subs r3,r3,#1
bne 2b
subs r2,r2,#1
bne 1b
/* set System PLL Control Register 0 */
ldr r0, =SPCTL0
ldr r1, =CONFIG_SYS_SPCTL0_VAL
str r1, [r0]
/* set spll restart bit */
ldr r0, =CSCR
ldr r1, [r0]
orr r1,r1,#(1<<22)
str r1, [r0]
mov r2,#0x10
1:
mov r3,#0x2000
2:
subs r3,r3,#1
bne 2b
subs r2,r2,#1
bne 1b
ldr r0, =CSCR
ldr r1, =CONFIG_SYS_CSCR_VAL
str r1, [r0]
/* I have now read the ARM920 DataSheet back-to-Back, and have stumbled upon
*this.....
*
* It would appear that from a Cold-Boot the ARM920T enters "FastBus" mode CP15
* register 1, this stops it using the output of the PLL and thus runs at the
* slow rate. Unless you place the Core into "Asynch" mode, the CPU will never
* use the value set in the CM_OSC registers...regardless of what you set it
* too! Thus, although i thought i was running at 140MHz, i'm actually running
* at 40!..
* Slapping this into my bootloader does the trick...
* MRC p15,0,r0,c1,c0,0 ; read core configuration register
* ORR r0,r0,#0xC0000000 ; set asynchronous clocks and not fastbus mode
* MCR p15,0,r0,c1,c0,0 ; write modified value to core configuration
* register
*/
MRC p15,0,r0,c1,c0,0
ORR r0,r0,#0xC0000000
MCR p15,0,r0,c1,c0,0
ldr r0, =GPR(0)
ldr r1, =CONFIG_SYS_GPR_A_VAL
str r1, [r0]
ldr r0, =GIUS(0)
ldr r1, =CONFIG_SYS_GIUS_A_VAL
str r1, [r0]
/* CS3 becomes CS3 by clearing reset default bit 1 in FMCR */
ldr r0, =FMCR
ldr r1, =CONFIG_SYS_FMCR_VAL
str r1, [r0]
ldr r0, =CS0U
ldr r1, =CONFIG_SYS_CS0U_VAL
str r1, [r0]
ldr r0, =CS0L
ldr r1, =CONFIG_SYS_CS0L_VAL
str r1, [r0]
ldr r0, =CS1U
ldr r1, =CONFIG_SYS_CS1U_VAL
str r1, [r0]
ldr r0, =CS1L
ldr r1, =CONFIG_SYS_CS1L_VAL
str r1, [r0]
ldr r0, =CS2U
ldr r1, =CONFIG_SYS_CS2U_VAL
str r1, [r0]
ldr r0, =CS2L
ldr r1, =CONFIG_SYS_CS2L_VAL
str r1, [r0]
ldr r0, =CS3U
ldr r1, =CONFIG_SYS_CS3U_VAL
str r1, [r0]
ldr r0, =CS3L
ldr r1, =CONFIG_SYS_CS3L_VAL
str r1, [r0]
ldr r0, =CS4U
ldr r1, =CONFIG_SYS_CS4U_VAL
str r1, [r0]
ldr r0, =CS4L
ldr r1, =CONFIG_SYS_CS4L_VAL
str r1, [r0]
ldr r0, =CS5U
ldr r1, =CONFIG_SYS_CS5U_VAL
str r1, [r0]
ldr r0, =CS5L
ldr r1, =CONFIG_SYS_CS5L_VAL
str r1, [r0]
/* SDRAM Setup */
ldr r0, =SDCTL0
ldr r1, =PRECHARGE_CMD
str r1, [r0]
ldr r0, =0x08200000
ldr r1, =0x0 /* Issue Precharge all Command */
str r1, [r0]
ldr r0, =SDCTL0
ldr r1, =AUTOREFRESH_CMD
str r1, [r0]
ldr r0, =0x08000000
ldr r1, =0x0 /* Issue AutoRefresh Command */
str r1, [r0]
str r1, [r0]
str r1, [r0]
str r1, [r0]
str r1, [r0]
str r1, [r0]
str r1, [r0]
str r1, [r0]
ldr r0, =SDCTL0
ldr r1, =0xb10a8300
str r1, [r0]
ldr r0, =0x08223000 /* CAS Latency 2 */
ldr r1, =0x0 /* Issue Mode Register Command, Burst Length = 8 */
str r1, [r0]
ldr r0, =SDCTL0
ldr r1, =0x810a8200 /* Set to Normal Mode CAS 2 */
str r1, [r0]
mov pc,r10