u-boot/board/freescale/imx8mp_evk/imx8mp_evk.c
Ye Li c852a2bf6f imx8mp_evk: Remove EQoS PHY reset codes
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-21 13:59:26 +02:00

102 lines
2.1 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2019 NXP
*/
#include <common.h>
#include <env.h>
#include <errno.h>
#include <init.h>
#include <miiphy.h>
#include <netdev.h>
#include <linux/delay.h>
#include <asm/global_data.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm-generic/gpio.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/gpio.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
static iomux_v3_cfg_t const uart_pads[] = {
MX8MP_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX8MP_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
int board_early_init_f(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
return 0;
}
static void setup_fec(void)
{
struct iomuxc_gpr_base_regs *gpr =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
/* Enable RGMII TX clk output */
setbits_le32(&gpr->gpr[1], BIT(22));
}
static int setup_eqos(void)
{
struct iomuxc_gpr_base_regs *gpr =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
/* set INTF as RGMII, enable RGMII TXC clock */
clrsetbits_le32(&gpr->gpr[1],
IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK, BIT(16));
setbits_le32(&gpr->gpr[1], BIT(19) | BIT(21));
return set_clk_eqos(ENET_125MHZ);
}
#if CONFIG_IS_ENABLED(NET)
int board_phy_config(struct phy_device *phydev)
{
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif
int board_init(void)
{
int ret = 0;
if (CONFIG_IS_ENABLED(FEC_MXC)) {
setup_fec();
}
if (CONFIG_IS_ENABLED(DWC_ETH_QOS)) {
ret = setup_eqos();
}
return ret;
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
env_set("board_name", "EVK");
env_set("board_rev", "iMX8MP");
#endif
return 0;
}