Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-04 18:41:03 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/hymod/hymod.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files 
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

521 lines
19 KiB
C
Raw Blame History

/*
* (C) Copyright 2000
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*
* Hacked for the Hymod board by Murray.Jensen@csiro.au, 20-Oct-00
*/
#include <common.h>
#include <mpc8260.h>
#include <mpc8260_irq.h>
#include <ioports.h>
#include <i2c.h>
#include <asm/iopin_8260.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/* imports from eeprom.c */
extern int hymod_eeprom_read (int, hymod_eeprom_t *);
extern void hymod_eeprom_print (hymod_eeprom_t *);
/* imports from env.c */
extern void hymod_check_env (void);
/* ------------------------------------------------------------------------- */
/*
* I/O Port configuration table
*
* if conf is 1, then that port pin will be configured at boot time
* according to the five values podr/pdir/ppar/psor/pdat for that entry
*/
const iop_conf_t iop_conf_tab[4][32] = {
/* Port A configuration */
{
/* cnf par sor dir odr dat */
{ 1, 1, 1, 0, 0, 0 }, /* PA31: FCC1 MII COL */
{ 1, 1, 1, 0, 0, 0 }, /* PA30: FCC1 MII CRS */
{ 1, 1, 1, 1, 0, 0 }, /* PA29: FCC1 MII TX_ER */
{ 1, 1, 1, 1, 0, 0 }, /* PA28: FCC1 MII TX_EN */
{ 1, 1, 1, 0, 0, 0 }, /* PA27: FCC1 MII RX_DV */
{ 1, 1, 1, 0, 0, 0 }, /* PA26: FCC1 MII RX_ER */
{ 1, 0, 0, 1, 0, 0 }, /* PA25: FCC2 MII MDIO */
{ 1, 0, 0, 1, 0, 0 }, /* PA24: FCC2 MII MDC */
{ 1, 0, 0, 1, 0, 0 }, /* PA23: FCC3 MII MDIO */
{ 1, 0, 0, 1, 0, 0 }, /* PA22: FCC3 MII MDC */
{ 1, 1, 0, 1, 0, 0 }, /* PA21: FCC1 MII TxD[3] */
{ 1, 1, 0, 1, 0, 0 }, /* PA20: FCC1 MII TxD[2] */
{ 1, 1, 0, 1, 0, 0 }, /* PA19: FCC1 MII TxD[1] */
{ 1, 1, 0, 1, 0, 0 }, /* PA18: FCC1 MII TxD[0] */
{ 1, 1, 0, 0, 0, 0 }, /* PA17: FCC1 MII RxD[3] */
{ 1, 1, 0, 0, 0, 0 }, /* PA16: FCC1 MII RxD[2] */
{ 1, 1, 0, 0, 0, 0 }, /* PA15: FCC1 MII RxD[1] */
{ 1, 1, 0, 0, 0, 0 }, /* PA14: FCC1 MII RxD[0] */
{ 1, 0, 0, 1, 0, 0 }, /* PA13: FCC1 MII MDIO */
{ 1, 0, 0, 1, 0, 0 }, /* PA12: FCC1 MII MDC */
{ 1, 0, 0, 1, 0, 0 }, /* PA11: SEL_CD */
{ 1, 0, 0, 0, 0, 0 }, /* PA10: FLASH STS1 */
{ 1, 0, 0, 0, 0, 0 }, /* PA09: FLASH STS0 */
{ 1, 0, 0, 0, 0, 0 }, /* PA08: FLASH ~PE */
{ 1, 0, 0, 0, 0, 0 }, /* PA07: WATCH ~HRESET */
{ 1, 0, 0, 0, 1, 0 }, /* PA06: VC DONE */
{ 1, 0, 0, 1, 1, 0 }, /* PA05: VC INIT */
{ 1, 0, 0, 1, 0, 0 }, /* PA04: VC ~PROG */
{ 1, 0, 0, 1, 0, 0 }, /* PA03: VM ENABLE */
{ 1, 0, 0, 0, 1, 0 }, /* PA02: VM DONE */
{ 1, 0, 0, 1, 1, 0 }, /* PA01: VM INIT */
{ 1, 0, 0, 1, 0, 0 } /* PA00: VM ~PROG */
},
/* Port B configuration */
{
/* cnf par sor dir odr dat */
{ 1, 1, 0, 1, 0, 0 }, /* PB31: FCC2 MII TX_ER */
{ 1, 1, 0, 0, 0, 0 }, /* PB30: FCC2 MII RX_DV */
{ 1, 1, 1, 1, 0, 0 }, /* PB29: FCC2 MII TX_EN */
{ 1, 1, 0, 0, 0, 0 }, /* PB28: FCC2 MII RX_ER */
{ 1, 1, 0, 0, 0, 0 }, /* PB27: FCC2 MII COL */
{ 1, 1, 0, 0, 0, 0 }, /* PB26: FCC2 MII CRS */
{ 1, 1, 0, 1, 0, 0 }, /* PB25: FCC2 MII TxD[3] */
{ 1, 1, 0, 1, 0, 0 }, /* PB24: FCC2 MII TxD[2] */
{ 1, 1, 0, 1, 0, 0 }, /* PB23: FCC2 MII TxD[1] */
{ 1, 1, 0, 1, 0, 0 }, /* PB22: FCC2 MII TxD[0] */
{ 1, 1, 0, 0, 0, 0 }, /* PB21: FCC2 MII RxD[0] */
{ 1, 1, 0, 0, 0, 0 }, /* PB20: FCC2 MII RxD[1] */
{ 1, 1, 0, 0, 0, 0 }, /* PB19: FCC2 MII RxD[2] */
{ 1, 1, 0, 0, 0, 0 }, /* PB18: FCC2 MII RxD[3] */
{ 1, 1, 0, 0, 0, 0 }, /* PB17: FCC3 MII RX_DV */
{ 1, 1, 0, 0, 0, 0 }, /* PB16: FCC3 MII RX_ER */
{ 1, 1, 0, 1, 0, 0 }, /* PB15: FCC3 MII TX_ER */
{ 1, 1, 0, 1, 0, 0 }, /* PB14: FCC3 MII TX_EN */
{ 1, 1, 0, 0, 0, 0 }, /* PB13: FCC3 MII COL */
{ 1, 1, 0, 0, 0, 0 }, /* PB12: FCC3 MII CRS */
{ 1, 1, 0, 0, 0, 0 }, /* PB11: FCC3 MII RxD[3] */
{ 1, 1, 0, 0, 0, 0 }, /* PB10: FCC3 MII RxD[2] */
{ 1, 1, 0, 0, 0, 0 }, /* PB09: FCC3 MII RxD[1] */
{ 1, 1, 0, 0, 0, 0 }, /* PB08: FCC3 MII RxD[0] */
{ 1, 1, 0, 1, 0, 0 }, /* PB07: FCC3 MII TxD[3] */
{ 1, 1, 0, 1, 0, 0 }, /* PB06: FCC3 MII TxD[2] */
{ 1, 1, 0, 1, 0, 0 }, /* PB05: FCC3 MII TxD[1] */
{ 1, 1, 0, 1, 0, 0 }, /* PB04: FCC3 MII TxD[0] */
{ 0, 0, 0, 0, 0, 0 }, /* PB03: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 }, /* PB02: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 }, /* PB01: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 } /* PB00: pin doesn't exist */
},
/* Port C configuration */
{
/* cnf par sor dir odr dat */
{ 1, 0, 0, 0, 0, 0 }, /* PC31: MEZ ~IACK */
{ 0, 0, 0, 0, 0, 0 }, /* PC30: ? */
{ 1, 1, 0, 0, 0, 0 }, /* PC29: CLK SCCx */
{ 1, 1, 0, 0, 0, 0 }, /* PC28: CLK4 */
{ 1, 1, 0, 0, 0, 0 }, /* PC27: CLK SCCF */
{ 1, 1, 0, 0, 0, 0 }, /* PC26: CLK 32K */
{ 1, 1, 0, 0, 0, 0 }, /* PC25: BRG4/CLK7 */
{ 0, 0, 0, 0, 0, 0 }, /* PC24: ? */
{ 1, 1, 0, 0, 0, 0 }, /* PC23: CLK SCCx */
{ 1, 1, 0, 0, 0, 0 }, /* PC22: FCC1 MII RX_CLK */
{ 1, 1, 0, 0, 0, 0 }, /* PC21: FCC1 MII TX_CLK */
{ 1, 1, 0, 0, 0, 0 }, /* PC20: CLK SCCF */
{ 1, 1, 0, 0, 0, 0 }, /* PC19: FCC2 MII RX_CLK */
{ 1, 1, 0, 0, 0, 0 }, /* PC18: FCC2 MII TX_CLK */
{ 1, 1, 0, 0, 0, 0 }, /* PC17: FCC3 MII RX_CLK */
{ 1, 1, 0, 0, 0, 0 }, /* PC16: FCC3 MII TX_CLK */
{ 1, 0, 0, 0, 0, 0 }, /* PC15: SCC1 UART ~CTS */
{ 1, 0, 0, 0, 0, 0 }, /* PC14: SCC1 UART ~CD */
{ 1, 0, 0, 0, 0, 0 }, /* PC13: SCC2 UART ~CTS */
{ 1, 0, 0, 0, 0, 0 }, /* PC12: SCC2 UART ~CD */
{ 1, 0, 0, 1, 0, 0 }, /* PC11: SCC1 UART ~DTR */
{ 1, 0, 0, 1, 0, 0 }, /* PC10: SCC1 UART ~DSR */
{ 1, 0, 0, 1, 0, 0 }, /* PC09: SCC2 UART ~DTR */
{ 1, 0, 0, 1, 0, 0 }, /* PC08: SCC2 UART ~DSR */
{ 1, 0, 0, 0, 0, 0 }, /* PC07: TEMP ~ALERT */
{ 1, 0, 0, 0, 0, 0 }, /* PC06: FCC3 INT */
{ 1, 0, 0, 0, 0, 0 }, /* PC05: FCC2 INT */
{ 1, 0, 0, 0, 0, 0 }, /* PC04: FCC1 INT */
{ 0, 1, 1, 1, 0, 0 }, /* PC03: SDMA IDMA2 ~DACK */
{ 0, 1, 1, 0, 0, 0 }, /* PC02: SDMA IDMA2 ~DONE */
{ 0, 1, 0, 0, 0, 0 }, /* PC01: SDMA IDMA2 ~DREQ */
{ 1, 1, 0, 1, 0, 0 } /* PC00: BRG7 */
},
/* Port D configuration */
{
/* cnf par sor dir odr dat */
{ 1, 1, 0, 0, 0, 0 }, /* PD31: SCC1 UART RxD */
{ 1, 1, 1, 1, 0, 0 }, /* PD30: SCC1 UART TxD */
{ 1, 0, 0, 1, 0, 0 }, /* PD29: SCC1 UART ~RTS */
{ 1, 1, 0, 0, 0, 0 }, /* PD28: SCC2 UART RxD */
{ 1, 1, 0, 1, 0, 0 }, /* PD27: SCC2 UART TxD */
{ 1, 0, 0, 1, 0, 0 }, /* PD26: SCC2 UART ~RTS */
{ 1, 0, 0, 0, 0, 0 }, /* PD25: SCC1 UART ~RI */
{ 1, 0, 0, 0, 0, 0 }, /* PD24: SCC2 UART ~RI */
{ 1, 0, 0, 1, 0, 0 }, /* PD23: CLKGEN PD */
{ 1, 0, 0, 0, 0, 0 }, /* PD22: USER3 */
{ 1, 0, 0, 0, 0, 0 }, /* PD21: USER2 */
{ 1, 0, 0, 0, 0, 0 }, /* PD20: USER1 */
{ 1, 1, 1, 0, 0, 0 }, /* PD19: SPI ~SEL */
{ 1, 1, 1, 0, 0, 0 }, /* PD18: SPI CLK */
{ 1, 1, 1, 0, 0, 0 }, /* PD17: SPI MOSI */
{ 1, 1, 1, 0, 0, 0 }, /* PD16: SPI MISO */
{ 1, 1, 1, 0, 1, 0 }, /* PD15: I2C SDA */
{ 1, 1, 1, 0, 1, 0 }, /* PD14: I2C SCL */
{ 1, 0, 0, 1, 0, 1 }, /* PD13: TEMP ~STDBY */
{ 1, 0, 0, 1, 0, 1 }, /* PD12: FCC3 ~RESET */
{ 1, 0, 0, 1, 0, 1 }, /* PD11: FCC2 ~RESET */
{ 1, 0, 0, 1, 0, 1 }, /* PD10: FCC1 ~RESET */
{ 1, 0, 0, 0, 0, 0 }, /* PD09: PD9 */
{ 1, 0, 0, 0, 0, 0 }, /* PD08: PD8 */
{ 1, 0, 0, 1, 0, 1 }, /* PD07: PD7 */
{ 1, 0, 0, 1, 0, 1 }, /* PD06: PD6 */
{ 1, 0, 0, 1, 0, 1 }, /* PD05: PD5 */
{ 1, 0, 0, 1, 0, 1 }, /* PD04: PD4 */
{ 0, 0, 0, 0, 0, 0 }, /* PD03: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 }, /* PD02: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 }, /* PD01: pin doesn't exist */
{ 0, 0, 0, 0, 0, 0 } /* PD00: pin doesn't exist */
}
};
/* ------------------------------------------------------------------------- */
/*
* AMI FS6377 Clock Generator configuration table
*
* the "fs6377_regs[]" table entries correspond to FS6377 registers
* 0 - 15 (total of 16 bytes).
*
* the data is written to the FS6377 via the i2c bus using address in
* "fs6377_addr" (address is 7 bits - R/W bit not included).
*
* The fs6377 has four clock outputs: A, B, C and D.
*
* Outputs C and D can each provide two different clock outputs C1/D1 or
* C2/D2 depending on the state of the SEL_CD input which is connected to
* the MPC8260 I/O port pin PA11. PA11 output (SEL_CD input) low (or 0)
* selects C1/D1 and PA11 output (SEL_CD input) high (or 1) selects C2/D2.
*
* PA11 defaults to output low (or 0) in the i/o port config table above.
*
* Output A provides a 100MHz for the High Speed Serial chips. Output B
* provides a 3.6864MHz clock for more accurate asynchronous serial bit
* rates. Output C is routed to the mezzanine connector but is currently
* unused - both C1 and C2 are set to 16MHz. Output D is used by both the
* alt-input and display mezzanine boards for their video chips. The
* alt-input board requires a clock of 24.576MHz and this is available on
* D1 (PA11=SEL_CD=0). The display board requires a clock of 27MHz and this
* is available on D2 (PA11=SEL_CD=1).
*
* So the default is a clock suitable for the alt-input board. PA11 is toggled
* later in misc_init_r(), if a display board is detected.
*/
uchar fs6377_addr = 0x5c;
uchar fs6377_regs[16] = {
12, 75, 64, 25, 144, 128, 25, 192,
0, 16, 135, 192, 224, 64, 64, 192
};
/* ------------------------------------------------------------------------- */
/*
* special board initialisation, after clocks and timebase have been
* set up but before environment and serial are initialised.
*
* added so that very early initialisations can be done using the i2c
* driver (which requires the clocks, to calculate the dividers, and
* the timebase, for udelay())
*/
int
board_postclk_init (void)
{
i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
/*
* Initialise the FS6377 clock chip
*
* the secondary address is the register number from where to
* start the write - I want to write all the registers
*
* don't bother checking return status - we have no console yet
* to print it on, nor any RAM to store it in - it will be obvious
* if this doesn't work
*/
(void) i2c_write (fs6377_addr, 0, 1, fs6377_regs,
sizeof (fs6377_regs));
return (0);
}
/* ------------------------------------------------------------------------- */
/*
* Check Board Identity: Hardwired to HYMOD
*/
int
checkboard (void)
{
puts ("Board: HYMOD\n");
return (0);
}
/* ------------------------------------------------------------------------- */
/*
* miscellaneous (early - while running in flash) initialisations.
*/
#define _NOT_USED_ 0xFFFFFFFF
uint upmb_table[] = {
/* Read Single Beat (RSS) - offset 0x00 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Read Burst (RBS) - offset 0x08 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Write Single Beat (WSS) - offset 0x18 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Write Burst (WSS) - offset 0x20 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Refresh Timer (PTS) - offset 0x30 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Exception Condition (EXS) - offset 0x3c */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_
};
uint upmc_table[] = {
/* Read Single Beat (RSS) - offset 0x00 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Read Burst (RBS) - offset 0x08 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Write Single Beat (WSS) - offset 0x18 */
0xF0E00000, 0xF0A00000, 0x00A00000, 0x30A00000,
0xF0F40007, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Write Burst (WSS) - offset 0x20 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Refresh Timer (PTS) - offset 0x30 */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/* Exception Condition (EXS) - offset 0x3c */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_
};
int
misc_init_f (void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8260_t *memctl = &immap->im_memctl;
printf ("UPMs: ");
upmconfig (UPMB, upmb_table, sizeof upmb_table / sizeof upmb_table[0]);
memctl->memc_mbmr = CONFIG_SYS_MBMR;
upmconfig (UPMC, upmc_table, sizeof upmc_table / sizeof upmc_table[0]);
memctl->memc_mcmr = CONFIG_SYS_MCMR;
printf ("configured\n");
return (0);
}
/* ------------------------------------------------------------------------- */
phys_size_t
initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8260_t *memctl = &immap->im_memctl;
volatile uchar c = 0, *ramaddr = (uchar *) (CONFIG_SYS_SDRAM_BASE + 0x8);
ulong psdmr = CONFIG_SYS_PSDMR;
int i;
/*
* Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
*
* "At system reset, initialization software must set up the
* programmable parameters in the memory controller banks registers
* (ORx, BRx, P/LSDMR). After all memory parameters are configured,
* system software should execute the following initialization sequence
* for each SDRAM device.
*
* 1. Issue a PRECHARGE-ALL-BANKS command
* 2. Issue eight CBR REFRESH commands
* 3. Issue a MODE-SET command to initialize the mode register
*
* The initial commands are executed by setting P/LSDMR[OP] and
* accessing the SDRAM with a single-byte transaction."
*
* The appropriate BRx/ORx registers have already been set when we
* get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
*/
memctl->memc_psrt = CONFIG_SYS_PSRT;
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
*ramaddr = c;
memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
for (i = 0; i < 8; i++)
*ramaddr = c;
memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
*ramaddr = c;
memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
*ramaddr = c;
return (CONFIG_SYS_SDRAM_SIZE << 20);
}
/* ------------------------------------------------------------------------- */
/* miscellaneous initialisations after relocation into ram (misc_init_r) */
/* */
/* loads the data in the main board and mezzanine board eeproms into */
/* the hymod configuration struct stored in the board information area. */
/* */
/* if the contents of either eeprom is invalid, prompts for a serial */
/* number (and an ethernet address if required) then fetches a file */
/* containing information to be stored in the eeprom from the tftp server */
/* (the file name is based on the serial number and a built-in path) */
int
last_stage_init (void)
{
hymod_conf_t *cp = &gd->bd->bi_hymod_conf;
int rc;
#ifdef CONFIG_BOOT_RETRY_TIME
/*
* we use the readline () function, but we also want
* command timeout enabled
*/
init_cmd_timeout ();
#endif
memset ((void *) cp, 0, sizeof (*cp));
/* set up main board config info */
rc = hymod_eeprom_read (0, &cp->main.eeprom);
puts ("EEPROM:main...");
if (rc < 0)
puts ("NOT PRESENT\n");
else if (rc == 0)
puts ("INVALID\n");
else {
cp->main.eeprom.valid = 1;
printf ("OK (ver %u)\n", cp->main.eeprom.ver);
hymod_eeprom_print (&cp->main.eeprom);
/*
* hard-wired assumption here: all hymod main boards will have
* one xilinx fpga, with the interrupt line connected to IRQ2
*
* One day, this might be based on the board type
*/
cp->main.xlx[0].mmap.prog.exists = 1;
cp->main.xlx[0].mmap.prog.size = FPGA_MAIN_CFG_SIZE;
cp->main.xlx[0].mmap.prog.base = FPGA_MAIN_CFG_BASE;
cp->main.xlx[0].mmap.reg.exists = 1;
cp->main.xlx[0].mmap.reg.size = FPGA_MAIN_REG_SIZE;
cp->main.xlx[0].mmap.reg.base = FPGA_MAIN_REG_BASE;
cp->main.xlx[0].mmap.port.exists = 1;
cp->main.xlx[0].mmap.port.size = FPGA_MAIN_PORT_SIZE;
cp->main.xlx[0].mmap.port.base = FPGA_MAIN_PORT_BASE;
cp->main.xlx[0].iopins.prog_pin.port = FPGA_MAIN_PROG_PORT;
cp->main.xlx[0].iopins.prog_pin.pin = FPGA_MAIN_PROG_PIN;
cp->main.xlx[0].iopins.prog_pin.flag = 1;
cp->main.xlx[0].iopins.init_pin.port = FPGA_MAIN_INIT_PORT;
cp->main.xlx[0].iopins.init_pin.pin = FPGA_MAIN_INIT_PIN;
cp->main.xlx[0].iopins.init_pin.flag = 1;
cp->main.xlx[0].iopins.done_pin.port = FPGA_MAIN_DONE_PORT;
cp->main.xlx[0].iopins.done_pin.pin = FPGA_MAIN_DONE_PIN;
cp->main.xlx[0].iopins.done_pin.flag = 1;
#ifdef FPGA_MAIN_ENABLE_PORT
cp->main.xlx[0].iopins.enable_pin.port = FPGA_MAIN_ENABLE_PORT;
cp->main.xlx[0].iopins.enable_pin.pin = FPGA_MAIN_ENABLE_PIN;
cp->main.xlx[0].iopins.enable_pin.flag = 1;
#endif
cp->main.xlx[0].irq = FPGA_MAIN_IRQ;
}
/* set up mezzanine board config info */
rc = hymod_eeprom_read (1, &cp->mezz.eeprom);
puts ("EEPROM:mezz...");
if (rc < 0)
puts ("NOT PRESENT\n");
else if (rc == 0)
puts ("INVALID\n");
else {
cp->main.eeprom.valid = 1;
printf ("OK (ver %u)\n", cp->mezz.eeprom.ver);
hymod_eeprom_print (&cp->mezz.eeprom);
}
cp->crc = crc32 (0, (unsigned char *)cp, offsetof (hymod_conf_t, crc));
hymod_check_env ();
return (0);
}
#ifdef CONFIG_SHOW_ACTIVITY
void board_show_activity (ulong timebase)
{
#ifdef CONFIG_SYS_HYMOD_DBLEDS
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile iop8260_t *iop = &immr->im_ioport;
static int shift = 0;
if ((timestamp % CONFIG_SYS_HZ) == 0) {
if (++shift > 3)
shift = 0;
iop->iop_pdatd =
(iop->iop_pdatd & ~0x0f000000) | (1 << (24 + shift));
}
#endif /* CONFIG_SYS_HYMOD_DBLEDS */
}
void show_activity(int arg)
{
}
#endif /* CONFIG_SHOW_ACTIVITY */
Reference in a new issue View git blame Copy permalink