mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 06:12:58 +00:00
320d266368
Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
101 lines
2.2 KiB
C
101 lines
2.2 KiB
C
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <power/pmic.h>
|
|
#include <power/stpmu1.h>
|
|
|
|
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
|
|
void board_debug_uart_init(void)
|
|
{
|
|
#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
|
|
|
|
#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
|
|
#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
|
|
|
|
/* UART4 clock enable */
|
|
setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
|
|
|
|
#define GPIOG_BASE 0x50008000
|
|
/* GPIOG clock enable */
|
|
writel(BIT(6), RCC_MP_AHB4ENSETR);
|
|
/* GPIO configuration for EVAL board
|
|
* => Uart4 TX = G11
|
|
*/
|
|
writel(0xffbfffff, GPIOG_BASE + 0x00);
|
|
writel(0x00006000, GPIOG_BASE + 0x24);
|
|
#else
|
|
|
|
#error("CONFIG_DEBUG_UART_BASE: not supported value")
|
|
|
|
#endif
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_PMIC_STPMU1
|
|
int board_ddr_power_init(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = uclass_get_device_by_driver(UCLASS_PMIC,
|
|
DM_GET_DRIVER(pmic_stpmu1), &dev);
|
|
if (ret)
|
|
/* No PMIC on board */
|
|
return 0;
|
|
|
|
/* Set LDO3 to sync mode */
|
|
ret = pmic_reg_read(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3));
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret &= ~STPMU1_LDO3_MODE;
|
|
ret &= ~STPMU1_LDO12356_OUTPUT_MASK;
|
|
ret |= STPMU1_LDO3_DDR_SEL << STPMU1_LDO12356_OUTPUT_SHIFT;
|
|
|
|
ret = pmic_reg_write(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
|
|
ret);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Set BUCK2 to 1.35V */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
|
|
STPMU1_BUCK_OUTPUT_MASK,
|
|
STPMU1_BUCK2_1350000V);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Enable BUCK2 and VREF */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
|
|
STPMU1_BUCK_EN, STPMU1_BUCK_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
ret = pmic_clrsetbits(dev, STPMU1_VREF_CTRL_REG,
|
|
STPMU1_VREF_EN, STPMU1_VREF_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
/* Enable LDO3 */
|
|
ret = pmic_clrsetbits(dev,
|
|
STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
|
|
STPMU1_LDO_EN, STPMU1_LDO_EN);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|