mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 01:38:22 +00:00
20337b75a7
Convert plain text documentation to reStructuredText format and add it to Sphinx TOC tree. No essential content change. Signed-off-by: Peng Fan <peng.fan@nxp.com>
98 lines
2.4 KiB
ReStructuredText
98 lines
2.4 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
mx6ul_14x14_evk
|
|
===============
|
|
|
|
How to use U-Boot on Freescale MX6UL 14x14 EVK
|
|
-----------------------------------------------
|
|
|
|
- Build U-Boot for MX6UL 14x14 EVK:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ make mrproper
|
|
$ make mx6ul_14x14_evk_defconfig
|
|
$ make
|
|
|
|
This will generate the SPL image called SPL and the u-boot.img.
|
|
|
|
1. Booting via SDCard
|
|
---------------------
|
|
|
|
- Flash the SPL image into the micro SD card:
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1 conv=notrunc; sync
|
|
|
|
- Flash the u-boot.img image into the micro SD card:
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69 conv=notrunc; sync
|
|
|
|
- Jumper settings::
|
|
|
|
SW601: 0 0 1 0
|
|
Sw602: 1 0
|
|
|
|
where 0 means bottom position and 1 means top position (from the
|
|
switch label numbers reference).
|
|
|
|
- Connect the USB cable between the EVK and the PC for the console.
|
|
The USB console connector is the one close the push buttons
|
|
|
|
- Insert the micro SD card in the board, power it up and U-Boot messages should come up.
|
|
|
|
2. Booting via Serial Download Protocol (SDP)
|
|
---------------------------------------------
|
|
|
|
The mx6ulevk board can boot from USB OTG port using the SDP, target will
|
|
enter in SDP mode in case an SD Card is not connect or boot switches are
|
|
set as below::
|
|
|
|
Sw602: 0 1
|
|
SW601: x x x x
|
|
|
|
The following tools can be used to boot via SDP, for both tools you must
|
|
connect an USB cable in USB OTG port.
|
|
|
|
- Method 1: Universal Update Utility (uuu)
|
|
|
|
The UUU binary can be downloaded in release tab from link below:
|
|
https://github.com/NXPmicro/mfgtools
|
|
|
|
The following script should be created to boot SPL + u-boot-dtb.img binaries:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ cat uuu_script
|
|
uuu_version 1.1.4
|
|
|
|
SDP: boot -f SPL
|
|
SDPU: write -f u-boot-dtb.img -addr 0x877fffc0
|
|
SDPU: jump -addr 0x877fffc0
|
|
SDPU: done
|
|
|
|
Please note that the address above is calculated based on SYS_TEXT_BASE address:
|
|
|
|
0x877fffc0 = 0x87800000 (SYS_TEXT_BASE) - 0x40 (U-Boot proper Header size)
|
|
|
|
Power on the target and run the following command from U-Boot root directory:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ sudo ./uuu uuu_script
|
|
|
|
- Method 2: imx usb loader tool (imx_usb):
|
|
|
|
The imx_usb_loader tool can be downloaded in link below:
|
|
https://github.com/boundarydevices/imx_usb_loader
|
|
|
|
Build the source code and run the following commands from U-Boot root
|
|
directory:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ sudo ./imx_usb SPL
|
|
$ sudo ./imx_usb u-boot-dtb.img
|