u-boot/include/configs/socfpga_common.h
Tom Rini 0613c36a7a global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-23 10:09:42 -05:00

162 lines
3.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2012 Altera Corporation <www.altera.com>
*/
#ifndef __CONFIG_SOCFPGA_COMMON_H__
#define __CONFIG_SOCFPGA_COMMON_H__
#include <linux/stringify.h>
/*
* Memory configurations
*/
#define PHYS_SDRAM_1 0x0
#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
#define CFG_SYS_INIT_RAM_ADDR 0xFFFF0000
#define CFG_SYS_INIT_RAM_SIZE SOCFPGA_PHYS_OCRAM_SIZE
#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
#define CFG_SYS_INIT_RAM_ADDR 0xFFE00000
/* SPL memory allocation configuration, this is for FAT implementation */
#define CFG_SYS_INIT_RAM_SIZE (SOCFPGA_PHYS_OCRAM_SIZE - \
CONFIG_SYS_SPL_MALLOC_SIZE)
#endif
/*
* Some boards (e.g. socfpga_sr1500) use 8 bytes at the end of the internal
* SRAM as bootcounter storage. Make sure to not put the stack directly
* at this address to not overwrite the bootcounter by checking, if the
* bootcounter address is located in the internal SRAM.
*/
#if ((CONFIG_SYS_BOOTCOUNT_ADDR > CFG_SYS_INIT_RAM_ADDR) && \
(CONFIG_SYS_BOOTCOUNT_ADDR < (CFG_SYS_INIT_RAM_ADDR + \
CFG_SYS_INIT_RAM_SIZE)))
#endif
/*
* U-Boot stack setup: if SPL post-reloc uses DDR stack, use it in pre-reloc
* phase of U-Boot, too. This prevents overwriting SPL data if stack/heap usage
* in U-Boot pre-reloc is higher than in SPL.
*/
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM_1
/*
* U-Boot general configurations
*/
/* Print buffer size */
/*
* Cache
*/
#define CFG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
* L4 OSC1 Timer 0
*/
#ifndef CONFIG_TIMER
#define CFG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
#define CFG_SYS_TIMER_COUNTER (CFG_SYS_TIMERBASE + 0x4)
#ifndef CFG_SYS_TIMER_RATE
#define CFG_SYS_TIMER_RATE 25000000
#endif
#endif
/*
* L4 Watchdog
*/
#define CFG_DW_WDT_CLOCK_KHZ 25000
/*
* NAND Support
*/
#ifdef CONFIG_NAND_DENALI
#define CFG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS
#define CFG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS
#endif
/*
* USB
*/
/*
* USB Gadget (DFU, UMS)
*/
#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
#define DFU_DEFAULT_POLL_TIMEOUT 300
#endif
/*
* U-Boot environment
*/
/* Environment for SDMMC boot */
/* Environment for QSPI boot */
/*
* SPL
*
* SRAM Memory layout for gen 5:
*
* 0xFFFF_0000 ...... Start of SRAM
* 0xFFFF_xxxx ...... Top of stack (grows down)
* 0xFFFF_yyyy ...... Global Data
* 0xFFFF_zzzz ...... Malloc area
* 0xFFFF_FFFF ...... End of SRAM
*
* SRAM Memory layout for Arria 10:
* 0xFFE0_0000 ...... Start of SRAM (bottom)
* 0xFFEx_xxxx ...... Top of stack (grows down to bottom)
* 0xFFEy_yyyy ...... Global Data
* 0xFFEz_zzzz ...... Malloc area (grows up to top)
* 0xFFE3_FFFF ...... End of SRAM (top)
*/
/* SPL QSPI boot support */
/* SPL NAND boot support */
/* Extra Environment */
#ifndef CONFIG_SPL_BUILD
#ifdef CONFIG_CMD_DHCP
#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
#else
#define BOOT_TARGET_DEVICES_DHCP(func)
#endif
#if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
#define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
#else
#define BOOT_TARGET_DEVICES_PXE(func)
#endif
#ifdef CONFIG_CMD_MMC
#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
#else
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_MMC(func) \
BOOT_TARGET_DEVICES_PXE(func) \
BOOT_TARGET_DEVICES_DHCP(func)
#include <config_distro_bootcmd.h>
#ifndef CFG_EXTRA_ENV_SETTINGS
#define CFG_EXTRA_ENV_SETTINGS \
"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"bootm_size=0xa000000\0" \
"kernel_addr_r="__stringify(CONFIG_SYS_LOAD_ADDR)"\0" \
"fdt_addr_r=0x02000000\0" \
"scriptaddr=0x02100000\0" \
"pxefile_addr_r=0x02200000\0" \
"ramdisk_addr_r=0x02300000\0" \
"socfpga_legacy_reset_compat=1\0" \
BOOTENV
#endif
#endif
#endif /* __CONFIG_SOCFPGA_COMMON_H__ */