mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 12:33:41 +00:00
5614e71b49
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
234 lines
8.5 KiB
C
234 lines
8.5 KiB
C
/*
|
|
* Copyright 2008 Extreme Engineering Solutions, Inc.
|
|
* Copyright 2008 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
|
|
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
|
|
{
|
|
i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
|
|
sizeof(ddr2_spd_eeprom_t));
|
|
}
|
|
|
|
/*
|
|
* There are four board-specific SDRAM timing parameters which must be
|
|
* calculated based on the particular PCB artwork. These are:
|
|
* 1.) CPO (Read Capture Delay)
|
|
* - TIMING_CFG_2 register
|
|
* Source: Calculation based on board trace lengths and
|
|
* chip-specific internal delays.
|
|
* 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
|
|
* - TIMING_CFG_2 register
|
|
* Source: Calculation based on board trace lengths.
|
|
* Unless clock and DQ lanes are very different
|
|
* lengths (>2"), this should be set to the nominal value
|
|
* of 1/2 clock delay.
|
|
* 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
|
|
* - DDR_SDRAM_CLK_CNTL register
|
|
* Source: Signal Integrity Simulations
|
|
* 4.) 2T Timing on Addr/Ctl
|
|
* - TIMING_CFG_2 register
|
|
* Source: Signal Integrity Simulations
|
|
* Usually only needed with heavy load/very high speed (>DDR2-800)
|
|
*
|
|
* ====== XPedite5370 DDR2-600 read delay calculations ======
|
|
*
|
|
* See Freescale's App Note AN2583 as refrence. This document also
|
|
* contains the chip-specific delays for 8548E, 8572, etc.
|
|
*
|
|
* For MPC8572E
|
|
* Minimum chip delay (Ch 0): 1.372ns
|
|
* Maximum chip delay (Ch 0): 2.914ns
|
|
* Minimum chip delay (Ch 1): 1.220ns
|
|
* Maximum chip delay (Ch 1): 2.595ns
|
|
*
|
|
* CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps
|
|
*
|
|
* Minimum delay calc (Ch 0):
|
|
* clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
|
|
* 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps
|
|
* = 3808ps
|
|
* = 3.808ns
|
|
*
|
|
* Maximum delay calc (Ch 0):
|
|
* clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
|
|
* 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps
|
|
* = 6240ps
|
|
* = 6.240ns
|
|
*
|
|
* Minimum delay calc (Ch 1):
|
|
* clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
|
|
* 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps
|
|
* = 3288ps
|
|
* = 3.288ns
|
|
*
|
|
* Maximum delay calc (Ch 1):
|
|
* clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
|
|
* 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps
|
|
* = 5536ps
|
|
* = 5.536ns
|
|
*
|
|
* Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target)
|
|
* This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
|
|
* Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target)
|
|
* This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7)
|
|
*
|
|
*
|
|
* ====== XPedite5370 DDR2-800 read delay calculations ======
|
|
*
|
|
* See Freescale's App Note AN2583 as refrence. This document also
|
|
* contains the chip-specific delays for 8548E, 8572, etc.
|
|
*
|
|
* For MPC8572E
|
|
* Minimum chip delay (Ch 0): 1.372ns
|
|
* Maximum chip delay (Ch 0): 2.914ns
|
|
* Minimum chip delay (Ch 1): 1.220ns
|
|
* Maximum chip delay (Ch 1): 2.595ns
|
|
*
|
|
* CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps
|
|
*
|
|
* Minimum delay calc (Ch 0):
|
|
* clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
|
|
* 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps
|
|
* = 3341ps
|
|
* = 3.341ns
|
|
*
|
|
* Maximum delay calc (Ch 0):
|
|
* clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
|
|
* 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps
|
|
* = 5673ps
|
|
* = 5.673ns
|
|
*
|
|
* Minimum delay calc (Ch 1):
|
|
* clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
|
|
* 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps
|
|
* = 2822ps
|
|
* = 2.822ns
|
|
*
|
|
* Maximum delay calc (Ch 1):
|
|
* clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
|
|
* 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps
|
|
* = 4968ps
|
|
* = 4.968ns
|
|
*
|
|
* Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target)
|
|
* This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9)
|
|
* Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target)
|
|
* This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
|
|
*
|
|
* Write latency (WR_DATA_DELAY) is calculated by doing the following:
|
|
*
|
|
* The DDR SDRAM specification requires DQS be received no sooner than
|
|
* 75% of an SDRAM clock period—and no later than 125% of a clock
|
|
* period—from the capturing clock edge of the command/address at the
|
|
* SDRAM.
|
|
*
|
|
* Based on the above tracelengths, the following are calculated:
|
|
* Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns
|
|
* Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns
|
|
* Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns
|
|
* Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns
|
|
*
|
|
* Difference in arrival time CLK vs. DQS:
|
|
* Ch. 0 0.072ns
|
|
* Ch. 1 0.138ns
|
|
*
|
|
* Both of these values are much less than 25% of the clock
|
|
* period at DDR2-600 or DDR2-800, so no additional delay is needed over
|
|
* the 1/2 cycle which normally aligns the first DQS transition
|
|
* exactly WL (CAS latency minus one cycle) after the CAS strobe.
|
|
* See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's
|
|
* terminology corresponds to exactly one clock period delay after
|
|
* the CAS strobe. (due to the fact that the "delay" is referenced
|
|
* from the *falling* edge of the CLK, just after the rising edge
|
|
* which the CAS strobe is latched on.
|
|
*/
|
|
|
|
typedef struct board_memctl_options {
|
|
uint16_t datarate_mhz_low;
|
|
uint16_t datarate_mhz_high;
|
|
uint8_t clk_adjust;
|
|
uint8_t cpo_override;
|
|
uint8_t write_data_delay;
|
|
} board_memctl_options_t;
|
|
|
|
static struct board_memctl_options bopts_ctrl[][2] = {
|
|
{
|
|
/* Controller 0 */
|
|
{
|
|
/* DDR2 600/667 */
|
|
.datarate_mhz_low = 500,
|
|
.datarate_mhz_high = 750,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 8,
|
|
.write_data_delay = 2,
|
|
},
|
|
{
|
|
/* DDR2 800 */
|
|
.datarate_mhz_low = 750,
|
|
.datarate_mhz_high = 850,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 9,
|
|
.write_data_delay = 2,
|
|
},
|
|
},
|
|
{
|
|
/* Controller 1 */
|
|
{
|
|
/* DDR2 600/667 */
|
|
.datarate_mhz_low = 500,
|
|
.datarate_mhz_high = 750,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 7,
|
|
.write_data_delay = 2,
|
|
},
|
|
{
|
|
/* DDR2 800 */
|
|
.datarate_mhz_low = 750,
|
|
.datarate_mhz_high = 850,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 8,
|
|
.write_data_delay = 2,
|
|
},
|
|
},
|
|
};
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
|
|
sys_info_t sysinfo;
|
|
int i;
|
|
unsigned int datarate;
|
|
|
|
get_sys_info(&sysinfo);
|
|
datarate = sysinfo.freq_ddrbus / 1000 / 1000;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
|
|
if ((bopts[i].datarate_mhz_low <= datarate) &&
|
|
(bopts[i].datarate_mhz_high >= datarate)) {
|
|
debug("controller %d:\n", ctrl_num);
|
|
debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
|
|
debug(" cpo = %d\n", bopts[i].cpo_override);
|
|
debug(" write_data_delay = %d\n",
|
|
bopts[i].write_data_delay);
|
|
popts->clk_adjust = bopts[i].clk_adjust;
|
|
popts->cpo_override = bopts[i].cpo_override;
|
|
popts->write_data_delay = bopts[i].write_data_delay;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 0;
|
|
}
|