u-boot/board/atmel/at91sam9261ek/at91sam9261ek.c
Grygorii Strashko 31f8d39e2a board: atmel: use get_nand_dev_by_index()
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2017-07-11 22:41:51 -04:00

278 lines
7.4 KiB
C

/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/at91sam9261.h>
#include <asm/arch/at91sam9261_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <lcd.h>
#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
#include <net.h>
#include <netdev.h>
#endif
#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
static void at91sam9261ek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
#ifdef CONFIG_AT91SAM9G10EK
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
&smc->cs[3].cycle);
#else
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
#endif
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOC);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */
}
#endif
#ifdef CONFIG_DRIVER_DM9000
static void at91sam9261ek_dm9000_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
/* Configure SMC CS2 for DM9000 */
#ifdef CONFIG_AT91SAM9G10EK
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[2].setup);
writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
&smc->cs[2].pulse);
writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
&smc->cs[2].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[2].mode);
#else
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[2].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
&smc->cs[2].pulse);
writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
&smc->cs[2].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[2].mode);
#endif
/* Configure Reset signal as output */
at91_set_gpio_output(AT91_PIN_PC10, 0);
/* Configure Interrupt pin as input, no pull-up */
at91_set_gpio_input(AT91_PIN_PC11, 0);
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 240,
.vl_row = 320,
.vl_clk = 4965000,
.vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
ATMEL_LCDC_INVFRAME_INVERTED,
.vl_bpix = 3,
.vl_tft = 1,
.vl_hsync_len = 5,
.vl_left_margin = 1,
.vl_right_margin = 33,
.vl_vsync_len = 1,
.vl_upper_margin = 1,
.vl_lower_margin = 0,
.mmio = ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
}
void lcd_disable(void)
{
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
}
static void at91sam9261ek_lcd_hw_init(void)
{
at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */
at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */
at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */
at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */
at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */
at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */
at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */
at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */
at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */
at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */
at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */
at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */
at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */
at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */
at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */
at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */
at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */
at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */
at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */
at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */
at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */
at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */
at91_system_clk_enable(AT91_PMC_HCK1);
/* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
#ifdef CONFIG_AT91SAM9261EK
gd->fb_base = ATMEL_BASE_SRAM;
#endif
}
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
void lcd_show_board_info(void)
{
ulong dram_size, nand_size;
int i;
char temp[32];
lcd_printf ("%s\n", U_BOOT_VERSION);
lcd_printf ("(C) 2008 ATMEL Corp\n");
lcd_printf ("at91support@atmel.com\n");
lcd_printf ("%s CPU at %s MHz\n",
ATMEL_CPU_NAME,
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += get_nand_dev_by_index(i)->size;
lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,
nand_size >> 20 );
}
#endif /* CONFIG_LCD_INFO */
#endif
int board_init(void)
{
#ifdef CONFIG_AT91SAM9G10EK
/* arch number of AT91SAM9G10EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
#else
/* arch number of AT91SAM9261EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
#endif
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
at91_seriald_hw_init();
#ifdef CONFIG_CMD_NAND
at91sam9261ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_DRIVER_DM9000
at91sam9261ek_dm9000_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9261ek_lcd_hw_init();
#endif
return 0;
}
#ifdef CONFIG_DRIVER_DM9000
int board_eth_init(bd_t *bis)
{
return dm9000_initialize(bis);
}
#endif
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
#ifdef CONFIG_DRIVER_DM9000
/*
* Initialize ethernet HW addr prior to starting Linux,
* needed for nfsroot
*/
eth_init();
#endif
}
#endif