u-boot/include/configs/omap5_uevm.h
Sam Protsenko adc097e133 env: ti: boot: Use ttyS2 instead of ttyO2
ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.

Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.

Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:

    compatible = "ti,dra742-uart", "ti,omap4-uart";

So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.

[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-27 13:36:54 -04:00

64 lines
1.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2013
* Texas Instruments Incorporated.
* Sricharan R <r.sricharan@ti.com>
*
* Configuration settings for the TI EVM5430 board.
* See ti_omap5_common.h for omap5 common settings.
*/
#ifndef __CONFIG_OMAP5_EVM_H
#define __CONFIG_OMAP5_EVM_H
#include <environment/ti/dfu.h>
#ifndef CONFIG_SPL_BUILD
/* Define the default GPT table for eMMC */
#define PARTS_DEFAULT \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
#endif
#define DFUARGS \
"dfu_bufsiz=0x10000\0" \
DFU_ALT_INFO_MMC \
DFU_ALT_INFO_EMMC \
DFU_ALT_INFO_RAM
#include <configs/ti_omap5_common.h>
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
/* MMC ENV related defines */
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
/* Enhance our eMMC support / experience. */
#define CONFIG_HSMMC2_8BIT
/* Required support for the TCA642X GPIO we have on the uEVM */
#define CONFIG_TCA642X
#define CONFIG_SYS_I2C_TCA642X_BUS_NUM 4
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
/* USB UHH support options */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 80
#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 79
/* Enabled commands */
/* USB Networking options */
#define CONSOLEDEV "ttyS2"
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#endif /* __CONFIG_OMAP5_EVM_H */