mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 17:41:08 +00:00
71e6840279
This document describes the SPL process for OMAP3 (and related) boards as well as a partial memory map and how to verify certain aspects outside of running on the target. Signed-off-by: Tom Rini <trini@ti.com>
74 lines
3 KiB
Text
74 lines
3 KiB
Text
Overview of SPL on OMAP3 devices
|
|
================================
|
|
|
|
Introduction
|
|
------------
|
|
|
|
This document provides an overview of how SPL functions on OMAP3 (and related
|
|
such as am35x and am37x) processors.
|
|
|
|
Methodology
|
|
-----------
|
|
|
|
On these platforms the ROM supports trying a sequence of boot devices. Once
|
|
one has been used successfully to load SPL this information is stored in memory
|
|
and the location stored in a register. We will read this to determine where to
|
|
read U-Boot from in turn.
|
|
|
|
Memory Map
|
|
----------
|
|
|
|
This is an example of a typical setup. See top-level README for documentation
|
|
of which CONFIG variables control these values. For a given board and the
|
|
amount of DRAM available to it different values may need to be used.
|
|
Note that the size of the SPL text rodata and data is enforced with a CONFIG
|
|
option and growing over that size results in a link error. The SPL stack
|
|
starts at the top of SRAM (which is configurable) and grows downward. The
|
|
space between the top of SRAM and the enforced upper bound on the size of the
|
|
SPL text, data and rodata is considered the safe stack area. Details on
|
|
confirming this behavior are shown below.
|
|
|
|
A portion of the system memory map looks as follows:
|
|
SRAM: 0x40200000 - 0x4020FFFF
|
|
DDR1: 0x80000000 - 0xBFFFFFFF
|
|
|
|
Option 1 (SPL only):
|
|
0x40200800 - 0x4020BBFF: Area for SPL text, data and rodata
|
|
0x4020BC00 - 0x4020FFFC: Area for the SPL stack.
|
|
0x80000000 - 0x8007FFFF: Area for the SPL BSS.
|
|
0x80100000: CONFIG_SYS_TEXT_BASE of U-Boot
|
|
0x80208000 - 0x80307FFF: malloc() pool available to SPL.
|
|
|
|
Option 2 (SPL or X-Loader):
|
|
0x40200800 - 0x4020BBFF: Area for SPL text, data and rodata
|
|
0x4020BC00 - 0x4020FFFC: Area for the SPL stack.
|
|
0x80008000: CONFIG_SYS_TEXT_BASE of U-Boot
|
|
0x87000000 - 0x8707FFFF: Area for the SPL BSS.
|
|
0x87080000 - 0x870FFFFF: malloc() pool available to SPL.
|
|
|
|
For the areas that reside within DDR1 they must not be used prior to s_init()
|
|
completing. Note that CONFIG_SYS_TEXT_BASE must be clear of the areas that SPL
|
|
uses while running. This is why we have two versions of the memory map that
|
|
only vary in where the BSS and malloc pool reside.
|
|
|
|
Estimating stack usage
|
|
----------------------
|
|
|
|
With gcc 4.6 (and later) and the use of GNU cflow it is possible to estimate
|
|
stack usage at various points in run sequence of SPL. The -fstack-usage option
|
|
to gcc will produce '.su' files (such as arch/arm/cpu/armv7/syslib.su) that
|
|
will give stack usage information and cflow can construct program flow.
|
|
|
|
Must have gcc 4.6 or later, which supports -fstack-usage
|
|
|
|
1) Build normally
|
|
2) Perform the following shell command to generate a list of C files used in
|
|
SPL:
|
|
$ find spl -name '*.su' | sed -e 's:^spl/::' -e 's:[.]su$:.c:' > used-spl.list
|
|
3) Execute cflow:
|
|
$ cflow --main=board_init_r `cat used-spl.list` 2>&1 | $PAGER
|
|
|
|
cflow will spit out a number of warnings as it does not parse
|
|
the config files and picks functions based on #ifdef. Parsing the '.i'
|
|
files instead introduces another set of headaches. These warnings are
|
|
not usually important to understanding the flow, however.
|