mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 15:37:23 +00:00
96b109ba74
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
313 lines
8.8 KiB
C
313 lines
8.8 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* clock_am33xx.c
|
|
*
|
|
* clocks for AM33XX based boards
|
|
*
|
|
* Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/io.h>
|
|
|
|
#define OSC (V_OSCK/1000000)
|
|
|
|
struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
|
|
struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;
|
|
struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL;
|
|
struct cm_rtc *const cmrtc = (struct cm_rtc *)CM_RTC;
|
|
|
|
const struct dpll_regs dpll_mpu_regs = {
|
|
.cm_clkmode_dpll = CM_WKUP + 0x88,
|
|
.cm_idlest_dpll = CM_WKUP + 0x20,
|
|
.cm_clksel_dpll = CM_WKUP + 0x2C,
|
|
.cm_div_m2_dpll = CM_WKUP + 0xA8,
|
|
};
|
|
|
|
const struct dpll_regs dpll_core_regs = {
|
|
.cm_clkmode_dpll = CM_WKUP + 0x90,
|
|
.cm_idlest_dpll = CM_WKUP + 0x5C,
|
|
.cm_clksel_dpll = CM_WKUP + 0x68,
|
|
.cm_div_m4_dpll = CM_WKUP + 0x80,
|
|
.cm_div_m5_dpll = CM_WKUP + 0x84,
|
|
.cm_div_m6_dpll = CM_WKUP + 0xD8,
|
|
};
|
|
|
|
const struct dpll_regs dpll_per_regs = {
|
|
.cm_clkmode_dpll = CM_WKUP + 0x8C,
|
|
.cm_idlest_dpll = CM_WKUP + 0x70,
|
|
.cm_clksel_dpll = CM_WKUP + 0x9C,
|
|
.cm_div_m2_dpll = CM_WKUP + 0xAC,
|
|
};
|
|
|
|
const struct dpll_regs dpll_ddr_regs = {
|
|
.cm_clkmode_dpll = CM_WKUP + 0x94,
|
|
.cm_idlest_dpll = CM_WKUP + 0x34,
|
|
.cm_clksel_dpll = CM_WKUP + 0x40,
|
|
.cm_div_m2_dpll = CM_WKUP + 0xA0,
|
|
};
|
|
|
|
const struct dpll_regs dpll_disp_regs = {
|
|
.cm_clkmode_dpll = CM_WKUP + 0x98,
|
|
.cm_idlest_dpll = CM_WKUP + 0x48,
|
|
.cm_clksel_dpll = CM_WKUP + 0x54,
|
|
.cm_div_m2_dpll = CM_WKUP + 0xA4,
|
|
};
|
|
|
|
struct dpll_params dpll_mpu_opp100 = {
|
|
CONFIG_SYS_MPUCLK, OSC-1, 1, -1, -1, -1, -1};
|
|
const struct dpll_params dpll_core_opp100 = {
|
|
1000, OSC-1, -1, -1, 10, 8, 4};
|
|
|
|
const struct dpll_params dpll_mpu_opp[NUM_CRYSTAL_FREQ][NUM_OPPS] = {
|
|
{ /* 19.2 MHz */
|
|
{125, 3, 2, -1, -1, -1, -1}, /* OPP 50 */
|
|
{-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */
|
|
{125, 3, 1, -1, -1, -1, -1}, /* OPP 100 */
|
|
{150, 3, 1, -1, -1, -1, -1}, /* OPP 120 */
|
|
{125, 2, 1, -1, -1, -1, -1}, /* OPP TB */
|
|
{625, 11, 1, -1, -1, -1, -1} /* OPP NT */
|
|
},
|
|
{ /* 24 MHz */
|
|
{25, 0, 2, -1, -1, -1, -1}, /* OPP 50 */
|
|
{-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */
|
|
{25, 0, 1, -1, -1, -1, -1}, /* OPP 100 */
|
|
{30, 0, 1, -1, -1, -1, -1}, /* OPP 120 */
|
|
{100, 2, 1, -1, -1, -1, -1}, /* OPP TB */
|
|
{125, 2, 1, -1, -1, -1, -1} /* OPP NT */
|
|
},
|
|
{ /* 25 MHz */
|
|
{24, 0, 2, -1, -1, -1, -1}, /* OPP 50 */
|
|
{-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */
|
|
{24, 0, 1, -1, -1, -1, -1}, /* OPP 100 */
|
|
{144, 4, 1, -1, -1, -1, -1}, /* OPP 120 */
|
|
{32, 0, 1, -1, -1, -1, -1}, /* OPP TB */
|
|
{40, 0, 1, -1, -1, -1, -1} /* OPP NT */
|
|
},
|
|
{ /* 26 MHz */
|
|
{300, 12, 2, -1, -1, -1, -1}, /* OPP 50 */
|
|
{-1, -1, -1, -1, -1, -1, -1}, /* OPP RESERVED */
|
|
{300, 12, 1, -1, -1, -1, -1}, /* OPP 100 */
|
|
{360, 12, 1, -1, -1, -1, -1}, /* OPP 120 */
|
|
{400, 12, 1, -1, -1, -1, -1}, /* OPP TB */
|
|
{500, 12, 1, -1, -1, -1, -1} /* OPP NT */
|
|
},
|
|
};
|
|
|
|
const struct dpll_params dpll_core_1000MHz[NUM_CRYSTAL_FREQ] = {
|
|
{625, 11, -1, -1, 10, 8, 4}, /* 19.2 MHz */
|
|
{125, 2, -1, -1, 10, 8, 4}, /* 24 MHz */
|
|
{40, 0, -1, -1, 10, 8, 4}, /* 25 MHz */
|
|
{500, 12, -1, -1, 10, 8, 4} /* 26 MHz */
|
|
};
|
|
|
|
const struct dpll_params dpll_per_192MHz[NUM_CRYSTAL_FREQ] = {
|
|
{400, 7, 5, -1, -1, -1, -1}, /* 19.2 MHz */
|
|
{400, 9, 5, -1, -1, -1, -1}, /* 24 MHz */
|
|
{384, 9, 5, -1, -1, -1, -1}, /* 25 MHz */
|
|
{480, 12, 5, -1, -1, -1, -1} /* 26 MHz */
|
|
};
|
|
|
|
const struct dpll_params dpll_ddr3_303MHz[NUM_CRYSTAL_FREQ] = {
|
|
{505, 15, 2, -1, -1, -1, -1}, /*19.2*/
|
|
{101, 3, 2, -1, -1, -1, -1}, /* 24 MHz */
|
|
{303, 24, 1, -1, -1, -1, -1}, /* 25 MHz */
|
|
{303, 12, 2, -1, -1, -1, -1} /* 26 MHz */
|
|
};
|
|
|
|
const struct dpll_params dpll_ddr3_400MHz[NUM_CRYSTAL_FREQ] = {
|
|
{125, 5, 1, -1, -1, -1, -1}, /*19.2*/
|
|
{50, 2, 1, -1, -1, -1, -1}, /* 24 MHz */
|
|
{16, 0, 1, -1, -1, -1, -1}, /* 25 MHz */
|
|
{200, 12, 1, -1, -1, -1, -1} /* 26 MHz */
|
|
};
|
|
|
|
const struct dpll_params dpll_ddr2_266MHz[NUM_CRYSTAL_FREQ] = {
|
|
{665, 47, 1, -1, -1, -1, -1}, /*19.2*/
|
|
{133, 11, 1, -1, -1, -1, -1}, /* 24 MHz */
|
|
{266, 24, 1, -1, -1, -1, -1}, /* 25 MHz */
|
|
{133, 12, 1, -1, -1, -1, -1} /* 26 MHz */
|
|
};
|
|
|
|
__weak const struct dpll_params *get_dpll_mpu_params(void)
|
|
{
|
|
return &dpll_mpu_opp100;
|
|
}
|
|
|
|
const struct dpll_params *get_dpll_core_params(void)
|
|
{
|
|
int ind = get_sys_clk_index();
|
|
|
|
return &dpll_core_1000MHz[ind];
|
|
}
|
|
|
|
const struct dpll_params *get_dpll_per_params(void)
|
|
{
|
|
int ind = get_sys_clk_index();
|
|
|
|
return &dpll_per_192MHz[ind];
|
|
}
|
|
|
|
void setup_clocks_for_console(void)
|
|
{
|
|
clrsetbits_le32(&cmwkup->wkclkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
|
|
CD_CLKCTRL_CLKTRCTRL_SW_WKUP <<
|
|
CD_CLKCTRL_CLKTRCTRL_SHIFT);
|
|
|
|
clrsetbits_le32(&cmper->l4hsclkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
|
|
CD_CLKCTRL_CLKTRCTRL_SW_WKUP <<
|
|
CD_CLKCTRL_CLKTRCTRL_SHIFT);
|
|
|
|
clrsetbits_le32(&cmwkup->wkup_uart0ctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
clrsetbits_le32(&cmper->uart1clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
clrsetbits_le32(&cmper->uart2clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
clrsetbits_le32(&cmper->uart3clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
clrsetbits_le32(&cmper->uart4clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
clrsetbits_le32(&cmper->uart5clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
}
|
|
|
|
void enable_basic_clocks(void)
|
|
{
|
|
u32 *const clk_domains[] = {
|
|
&cmper->l3clkstctrl,
|
|
&cmper->l4fwclkstctrl,
|
|
&cmper->l3sclkstctrl,
|
|
&cmper->l4lsclkstctrl,
|
|
&cmwkup->wkclkstctrl,
|
|
&cmper->emiffwclkctrl,
|
|
&cmrtc->clkstctrl,
|
|
0
|
|
};
|
|
|
|
u32 *const clk_modules_explicit_en[] = {
|
|
&cmper->l3clkctrl,
|
|
&cmper->l4lsclkctrl,
|
|
&cmper->l4fwclkctrl,
|
|
&cmwkup->wkl4wkclkctrl,
|
|
&cmper->l3instrclkctrl,
|
|
&cmper->l4hsclkctrl,
|
|
&cmwkup->wkgpio0clkctrl,
|
|
&cmwkup->wkctrlclkctrl,
|
|
&cmper->timer2clkctrl,
|
|
&cmper->gpmcclkctrl,
|
|
&cmper->elmclkctrl,
|
|
&cmper->mmc0clkctrl,
|
|
&cmper->mmc1clkctrl,
|
|
&cmwkup->wkup_i2c0ctrl,
|
|
&cmper->gpio1clkctrl,
|
|
&cmper->gpio2clkctrl,
|
|
&cmper->gpio3clkctrl,
|
|
&cmper->i2c1clkctrl,
|
|
&cmper->cpgmac0clkctrl,
|
|
&cmper->spi0clkctrl,
|
|
&cmrtc->rtcclkctrl,
|
|
&cmper->usb0clkctrl,
|
|
&cmper->emiffwclkctrl,
|
|
&cmper->emifclkctrl,
|
|
#if CONFIG_IS_ENABLED(AM335X_LCD)
|
|
&cmper->lcdclkctrl,
|
|
&cmper->lcdcclkstctrl,
|
|
#endif
|
|
0
|
|
};
|
|
|
|
do_enable_clocks(clk_domains, clk_modules_explicit_en, 1);
|
|
|
|
/* Select the Master osc 24 MHZ as Timer2 clock source */
|
|
writel(0x1, &cmdpll->clktimer2clk);
|
|
}
|
|
|
|
/*
|
|
* Enable Spread Spectrum for the MPU by calculating the required
|
|
* values and setting the registers accordingly.
|
|
* @param permille The spreading in permille (10th of a percent)
|
|
*/
|
|
void set_mpu_spreadspectrum(int permille)
|
|
{
|
|
u32 multiplier_m;
|
|
u32 predivider_n;
|
|
u32 cm_clksel_dpll_mpu;
|
|
u32 cm_clkmode_dpll_mpu;
|
|
u32 ref_clock;
|
|
u32 pll_bandwidth;
|
|
u32 mod_freq_divider;
|
|
u32 exponent;
|
|
u32 mantissa;
|
|
u32 delta_m_step;
|
|
|
|
printf("Enabling Spread Spectrum of %d permille for MPU\n",
|
|
permille);
|
|
|
|
/* Read PLL parameter m and n */
|
|
cm_clksel_dpll_mpu = readl(&cmwkup->clkseldpllmpu);
|
|
multiplier_m = (cm_clksel_dpll_mpu >> 8) & 0x3FF;
|
|
predivider_n = cm_clksel_dpll_mpu & 0x7F;
|
|
|
|
/*
|
|
* Calculate reference clock (clock after pre-divider),
|
|
* its max. PLL bandwidth,
|
|
* and resulting mod_freq_divider
|
|
*/
|
|
ref_clock = V_OSCK / (predivider_n + 1);
|
|
pll_bandwidth = ref_clock / 70;
|
|
mod_freq_divider = ref_clock / (4 * pll_bandwidth);
|
|
|
|
/* Calculate Mantissa/Exponent */
|
|
exponent = 0;
|
|
mantissa = mod_freq_divider;
|
|
while ((mantissa > 127) && (exponent < 7)) {
|
|
exponent++;
|
|
mantissa /= 2;
|
|
}
|
|
if (mantissa > 127)
|
|
mantissa = 127;
|
|
|
|
mod_freq_divider = mantissa << exponent;
|
|
|
|
/*
|
|
* Calculate Modulation steps
|
|
* As we use Downspread only, the spread is twice the value of
|
|
* permille, so Div2!
|
|
* As it takes the value in percent, divide by ten!
|
|
*/
|
|
delta_m_step = ((u32)((multiplier_m * permille) / 10 / 2)) << 18;
|
|
delta_m_step /= 100;
|
|
delta_m_step /= mod_freq_divider;
|
|
if (delta_m_step > 0xFFFFF)
|
|
delta_m_step = 0xFFFFF;
|
|
|
|
/* Setup Spread Spectrum */
|
|
writel(delta_m_step, &cmwkup->sscdeltamstepdllmpu);
|
|
writel((exponent << 8) | mantissa, &cmwkup->sscmodfreqdivdpllmpu);
|
|
cm_clkmode_dpll_mpu = readl(&cmwkup->clkmoddpllmpu);
|
|
/* clear all SSC flags */
|
|
cm_clkmode_dpll_mpu &= ~(0xF << CM_CLKMODE_DPLL_SSC_EN_SHIFT);
|
|
/* enable SSC with Downspread only */
|
|
cm_clkmode_dpll_mpu |= CM_CLKMODE_DPLL_SSC_EN_MASK |
|
|
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK;
|
|
writel(cm_clkmode_dpll_mpu, &cmwkup->clkmoddpllmpu);
|
|
while (!(readl(&cmwkup->clkmoddpllmpu) & 0x2000))
|
|
;
|
|
}
|