mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
295 lines
7.1 KiB
C
295 lines
7.1 KiB
C
/*
|
|
* Copyright 2009-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/mmu.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/immap_85xx.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/io.h>
|
|
#include <miiphy.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <fsl_mdio.h>
|
|
#include <tsec.h>
|
|
#include <vsc7385.h>
|
|
#include <netdev.h>
|
|
#include <rtc.h>
|
|
#include <i2c.h>
|
|
#include <hwconfig.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define VSC7385_RST_SET 0x00080000
|
|
#define SLIC_RST_SET 0x00040000
|
|
#define SGMII_PHY_RST_SET 0x00020000
|
|
#define PCIE_RST_SET 0x00010000
|
|
#define RGMII_PHY_RST_SET 0x02000000
|
|
|
|
#define USB_RST_CLR 0x04000000
|
|
#define USB2_PORT_OUT_EN 0x01000000
|
|
|
|
#define GPIO_DIR 0x060f0000
|
|
|
|
#define BOARD_PERI_RST_SET VSC7385_RST_SET | SLIC_RST_SET | \
|
|
SGMII_PHY_RST_SET | PCIE_RST_SET | \
|
|
RGMII_PHY_RST_SET
|
|
|
|
#define SYSCLK_MASK 0x00200000
|
|
#define BOARDREV_MASK 0x10100000
|
|
#define BOARDREV_C 0x00100000
|
|
#define BOARDREV_D 0x00000000
|
|
|
|
#define SYSCLK_66 66666666
|
|
#define SYSCLK_100 100000000
|
|
|
|
unsigned long get_board_sys_clk(ulong dummy)
|
|
{
|
|
volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
|
|
u32 val_gpdat, sysclk_gpio;
|
|
|
|
val_gpdat = in_be32(&pgpio->gpdat);
|
|
sysclk_gpio = val_gpdat & SYSCLK_MASK;
|
|
|
|
if(sysclk_gpio == 0)
|
|
return SYSCLK_66;
|
|
else
|
|
return SYSCLK_100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_MMC
|
|
int board_early_init_f (void)
|
|
{
|
|
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
|
|
setbits_be32(&gur->pmuxcr,
|
|
(MPC85xx_PMUXCR_SDHC_CD |
|
|
MPC85xx_PMUXCR_SDHC_WP));
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int checkboard (void)
|
|
{
|
|
u32 val_gpdat, board_rev_gpio;
|
|
volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
|
|
char board_rev = 0;
|
|
struct cpu_type *cpu;
|
|
|
|
val_gpdat = in_be32(&pgpio->gpdat);
|
|
board_rev_gpio = val_gpdat & BOARDREV_MASK;
|
|
if (board_rev_gpio == BOARDREV_C)
|
|
board_rev = 'C';
|
|
else if (board_rev_gpio == BOARDREV_D)
|
|
board_rev = 'D';
|
|
else
|
|
panic ("Unexpected Board REV %x detected!!\n", board_rev_gpio);
|
|
|
|
cpu = gd->arch.cpu;
|
|
printf ("Board: %sRDB Rev%c\n", cpu->name, board_rev);
|
|
|
|
setbits_be32(&pgpio->gpdir, GPIO_DIR);
|
|
|
|
/*
|
|
* Bringing the following peripherals out of reset via GPIOs
|
|
* 0 = reset and 1 = out of reset
|
|
* GPIO12 - Reset to Ethernet Switch
|
|
* GPIO13 - Reset to SLIC/SLAC devices
|
|
* GPIO14 - Reset to SGMII_PHY_N
|
|
* GPIO15 - Reset to PCIe slots
|
|
* GPIO6 - Reset to RGMII PHY
|
|
* GPIO5 - Reset to USB3300 devices 1 = reset and 0 = out of reset
|
|
*/
|
|
clrsetbits_be32(&pgpio->gpdat, USB_RST_CLR, BOARD_PERI_RST_SET);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
|
|
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
|
|
ccsr_gpio_t *gpio = (void *)CONFIG_SYS_MPC85xx_GPIO_ADDR;
|
|
|
|
setbits_be32(&gpio->gpdir, USB2_PORT_OUT_EN);
|
|
setbits_be32(&gpio->gpdat, USB2_PORT_OUT_EN);
|
|
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_ELBC_OFF_USB2_ON);
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
|
|
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
|
|
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
unsigned int orig_bus = i2c_get_bus_num();
|
|
u8 i2c_data;
|
|
|
|
i2c_set_bus_num(1);
|
|
if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0,
|
|
1, &i2c_data, sizeof(i2c_data)) == 0) {
|
|
if (i2c_data & 0x2)
|
|
puts("NOR Flash Bank : Secondary\n");
|
|
else
|
|
puts("NOR Flash Bank : Primary\n");
|
|
|
|
if (i2c_data & 0x1) {
|
|
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
|
|
puts("SD/MMC : 8-bit Mode\n");
|
|
puts("eSPI : Disabled\n");
|
|
} else {
|
|
puts("SD/MMC : 4-bit Mode\n");
|
|
puts("eSPI : Enabled\n");
|
|
}
|
|
} else {
|
|
puts("Failed reading I2C Chip 0x18 on bus 1\n");
|
|
}
|
|
i2c_set_bus_num(orig_bus);
|
|
|
|
/*
|
|
* Remap Boot flash region to caching-inhibited
|
|
* so that flash can be erased properly.
|
|
*/
|
|
|
|
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
|
flush_dcache();
|
|
invalidate_icache();
|
|
|
|
/* invalidate existing TLB entry for flash */
|
|
disable_tlb(flash_esel);
|
|
|
|
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, flash_esel, BOOKE_PAGESZ_16M, 1);
|
|
rtc_reset();
|
|
return 0;
|
|
}
|
|
|
|
|
|
#ifdef CONFIG_TSEC_ENET
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct fsl_pq_mdio_info mdio_info;
|
|
struct tsec_info_struct tsec_info[4];
|
|
int num = 0;
|
|
char *tmp;
|
|
unsigned int vscfw_addr;
|
|
|
|
#ifdef CONFIG_TSEC1
|
|
SET_STD_TSEC_INFO(tsec_info[num], 1);
|
|
num++;
|
|
#endif
|
|
#ifdef CONFIG_TSEC2
|
|
SET_STD_TSEC_INFO(tsec_info[num], 2);
|
|
num++;
|
|
#endif
|
|
#ifdef CONFIG_TSEC3
|
|
SET_STD_TSEC_INFO(tsec_info[num], 3);
|
|
if (is_serdes_configured(SGMII_TSEC3)) {
|
|
puts("eTSEC3 is in sgmii mode.\n");
|
|
tsec_info[num].flags |= TSEC_SGMII;
|
|
}
|
|
num++;
|
|
#endif
|
|
if (!num) {
|
|
printf("No TSECs initialized\n");
|
|
return 0;
|
|
}
|
|
#ifdef CONFIG_VSC7385_ENET
|
|
/* If a VSC7385 microcode image is present, then upload it. */
|
|
if ((tmp = getenv ("vscfw_addr")) != NULL) {
|
|
vscfw_addr = simple_strtoul (tmp, NULL, 16);
|
|
printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
|
|
if (vsc7385_upload_firmware((void *) vscfw_addr,
|
|
CONFIG_VSC7385_IMAGE_SIZE))
|
|
puts("Failure uploading VSC7385 microcode.\n");
|
|
} else
|
|
puts("No address specified for VSC7385 microcode.\n");
|
|
#endif
|
|
|
|
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
|
|
mdio_info.name = DEFAULT_MII_NAME;
|
|
fsl_pq_mdio_init(bis, &mdio_info);
|
|
|
|
tsec_eth_init(bis, tsec_info, num);
|
|
|
|
return pci_eth_init(bis);
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_OF_BOARD_SETUP)
|
|
extern void ft_pci_board_setup(void *blob);
|
|
|
|
void ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
const char *soc_usb_compat = "fsl-usb2-dr";
|
|
int err, usb1_off, usb2_off;
|
|
phys_addr_t base;
|
|
phys_size_t size;
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
base = getenv_bootm_low();
|
|
size = getenv_bootm_size();
|
|
|
|
#if defined(CONFIG_PCI)
|
|
ft_pci_board_setup(blob);
|
|
#endif /* #if defined(CONFIG_PCI) */
|
|
|
|
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
|
|
|
#if defined(CONFIG_HAS_FSL_DR_USB)
|
|
fdt_fixup_dr_usb(blob, bd);
|
|
#endif
|
|
|
|
#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
|
|
/* Delete eLBC node as it is muxed with USB2 controller */
|
|
if (hwconfig("usb2")) {
|
|
const char *soc_elbc_compat = "fsl,p1020-elbc";
|
|
int off = fdt_node_offset_by_compatible(blob, -1,
|
|
soc_elbc_compat);
|
|
if (off < 0) {
|
|
printf("WARNING: could not find compatible node"
|
|
" %s: %s.\n", soc_elbc_compat,
|
|
fdt_strerror(off));
|
|
return;
|
|
}
|
|
err = fdt_del_node(blob, off);
|
|
if (err < 0) {
|
|
printf("WARNING: could not remove %s: %s.\n",
|
|
soc_elbc_compat, fdt_strerror(err));
|
|
}
|
|
return;
|
|
}
|
|
#endif
|
|
/* Delete USB2 node as it is muxed with eLBC */
|
|
usb1_off = fdt_node_offset_by_compatible(blob, -1,
|
|
soc_usb_compat);
|
|
if (usb1_off < 0) {
|
|
printf("WARNING: could not find compatible node"
|
|
" %s: %s.\n", soc_usb_compat,
|
|
fdt_strerror(usb1_off));
|
|
return;
|
|
}
|
|
usb2_off = fdt_node_offset_by_compatible(blob, usb1_off,
|
|
soc_usb_compat);
|
|
if (usb2_off < 0) {
|
|
printf("WARNING: could not find compatible node"
|
|
" %s: %s.\n", soc_usb_compat,
|
|
fdt_strerror(usb2_off));
|
|
return;
|
|
}
|
|
err = fdt_del_node(blob, usb2_off);
|
|
if (err < 0)
|
|
printf("WARNING: could not remove %s: %s.\n",
|
|
soc_usb_compat, fdt_strerror(err));
|
|
}
|
|
#endif
|