Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-11 13:56:30 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/include/commproc.h
Wolfgang Denk 1b0757eced PPC: remove dead boards (AMX860, c2mon, ETX094, IAD210, LANTEC, SCM) 
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years.  Get rid of the dead
weight.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
2012-10-28 20:17:25 +01:00

1667 lines
57 KiB
C
Raw Blame History

/*
* MPC8xx Communication Processor Module.
* Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
*
* (C) Copyright 2000-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* This file contains structures and information for the communication
* processor channels. Some CPM control and status is available
* throught the MPC8xx internal memory map. See immap.h for details.
* This file only contains what I need for the moment, not the total
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
*
* On the MBX board, EPPC-Bug loads CPM microcode into the first 512
* bytes of the DP RAM and relocates the I2C parameter area to the
* IDMA1 space. The remaining DP RAM is available for buffer descriptors
* or other use.
*/
#ifndef __CPM_8XX__
#define __CPM_8XX__
#include <linux/config.h>
#include <asm/8xx_immap.h>
/* CPM Command register.
*/
#define CPM_CR_RST ((ushort)0x8000)
#define CPM_CR_OPCODE ((ushort)0x0f00)
#define CPM_CR_CHAN ((ushort)0x00f0)
#define CPM_CR_FLG ((ushort)0x0001)
/* Some commands (there are more...later)
*/
#define CPM_CR_INIT_TRX ((ushort)0x0000)
#define CPM_CR_INIT_RX ((ushort)0x0001)
#define CPM_CR_INIT_TX ((ushort)0x0002)
#define CPM_CR_HUNT_MODE ((ushort)0x0003)
#define CPM_CR_STOP_TX ((ushort)0x0004)
#define CPM_CR_RESTART_TX ((ushort)0x0006)
#define CPM_CR_SET_GADDR ((ushort)0x0008)
/* Channel numbers.
*/
#define CPM_CR_CH_SCC1 ((ushort)0x0000)
#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
#define CPM_CR_CH_SCC2 ((ushort)0x0004)
#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */
#define CPM_CR_CH_SCC3 ((ushort)0x0008)
#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
#define CPM_CR_CH_SCC4 ((ushort)0x000c)
#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
/*
* DPRAM defines and allocation functions
*/
/* The dual ported RAM is multi-functional. Some areas can be (and are
* being) used for microcode. There is an area that can only be used
* as data ram for buffer descriptors, which is all we use right now.
* Currently the first 512 and last 256 bytes are used for microcode.
*/
#ifdef CONFIG_SYS_ALLOC_DPRAM
#define CPM_DATAONLY_BASE ((uint)0x0800)
#define CPM_DATAONLY_SIZE ((uint)0x0700)
#define CPM_DP_NOSPACE ((uint)0x7fffffff)
#else
#define CPM_SERIAL_BASE 0x0800
#define CPM_I2C_BASE 0x0820
#define CPM_SPI_BASE 0x0840
#define CPM_FEC_BASE 0x0860
#define CPM_SERIAL2_BASE 0x08E0
#define CPM_SCC_BASE 0x0900
#define CPM_POST_BASE 0x0980
#define CPM_WLKBD_BASE 0x0a00
#endif
#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
#define CPM_POST_WORD_ADDR 0x07FC
#else
#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
#endif
#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
#else
#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
#endif
#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
/* Export the base address of the communication processor registers
* and dual port ram.
*/
extern cpm8xx_t *cpmp; /* Pointer to comm processor */
/* Buffer descriptors used by many of the CPM protocols.
*/
typedef struct cpm_buf_desc {
ushort cbd_sc; /* Status and Control */
ushort cbd_datlen; /* Data length in buffer */
uint cbd_bufaddr; /* Buffer address in host memory */
} cbd_t;
#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */
#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
#define BD_SC_BR ((ushort)0x0020) /* Break received */
#define BD_SC_FR ((ushort)0x0010) /* Framing error */
#define BD_SC_PR ((ushort)0x0008) /* Parity error */
#define BD_SC_OV ((ushort)0x0002) /* Overrun */
#define BD_SC_CD ((ushort)0x0001) /* Carrier Detect lost */
/* Parameter RAM offsets.
*/
#define PROFF_SCC1 ((uint)0x0000)
#define PROFF_IIC ((uint)0x0080)
#define PROFF_SCC2 ((uint)0x0100)
#define PROFF_SPI ((uint)0x0180)
#define PROFF_SCC3 ((uint)0x0200)
#define PROFF_SMC1 ((uint)0x0280)
#define PROFF_SCC4 ((uint)0x0300)
#define PROFF_SMC2 ((uint)0x0380)
/* Define enough so I can at least use the serial port as a UART.
* The MBX uses SMC1 as the host serial port.
*/
typedef struct smc_uart {
ushort smc_rbase; /* Rx Buffer descriptor base address */
ushort smc_tbase; /* Tx Buffer descriptor base address */
u_char smc_rfcr; /* Rx function code */
u_char smc_tfcr; /* Tx function code */
ushort smc_mrblr; /* Max receive buffer length */
uint smc_rstate; /* Internal */
uint smc_idp; /* Internal */
ushort smc_rbptr; /* Internal */
ushort smc_ibc; /* Internal */
uint smc_rxtmp; /* Internal */
uint smc_tstate; /* Internal */
uint smc_tdp; /* Internal */
ushort smc_tbptr; /* Internal */
ushort smc_tbc; /* Internal */
uint smc_txtmp; /* Internal */
ushort smc_maxidl; /* Maximum idle characters */
ushort smc_tmpidl; /* Temporary idle counter */
ushort smc_brklen; /* Last received break length */
ushort smc_brkec; /* rcv'd break condition counter */
ushort smc_brkcr; /* xmt break count register */
ushort smc_rmask; /* Temporary bit mask */
u_char res1[8];
ushort smc_rpbase; /* Relocation pointer */
} smc_uart_t;
/* Function code bits.
*/
#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
/* SMC uart mode register.
*/
#define SMCMR_REN ((ushort)0x0001)
#define SMCMR_TEN ((ushort)0x0002)
#define SMCMR_DM ((ushort)0x000c)
#define SMCMR_SM_GCI ((ushort)0x0000)
#define SMCMR_SM_UART ((ushort)0x0020)
#define SMCMR_SM_TRANS ((ushort)0x0030)
#define SMCMR_SM_MASK ((ushort)0x0030)
#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
#define SMCMR_REVD SMCMR_PM_EVEN
#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
#define SMCMR_BS SMCMR_PEN
#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
/* SMC2 as Centronics parallel printer. It is half duplex, in that
* it can only receive or transmit. The parameter ram values for
* each direction are either unique or properly overlap, so we can
* include them in one structure.
*/
typedef struct smc_centronics {
ushort scent_rbase;
ushort scent_tbase;
u_char scent_cfcr;
u_char scent_smask;
ushort scent_mrblr;
uint scent_rstate;
uint scent_r_ptr;
ushort scent_rbptr;
ushort scent_r_cnt;
uint scent_rtemp;
uint scent_tstate;
uint scent_t_ptr;
ushort scent_tbptr;
ushort scent_t_cnt;
uint scent_ttemp;
ushort scent_max_sl;
ushort scent_sl_cnt;
ushort scent_character1;
ushort scent_character2;
ushort scent_character3;
ushort scent_character4;
ushort scent_character5;
ushort scent_character6;
ushort scent_character7;
ushort scent_character8;
ushort scent_rccm;
ushort scent_rccr;
} smc_cent_t;
/* Centronics Status Mask Register.
*/
#define SMC_CENT_F ((u_char)0x08)
#define SMC_CENT_PE ((u_char)0x04)
#define SMC_CENT_S ((u_char)0x02)
/* SMC Event and Mask register.
*/
#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
#define SMCM_BSY ((unsigned char)0x04)
#define SMCM_TX ((unsigned char)0x02)
#define SMCM_RX ((unsigned char)0x01)
/* Baud rate generators.
*/
#define CPM_BRG_RST ((uint)0x00020000)
#define CPM_BRG_EN ((uint)0x00010000)
#define CPM_BRG_EXTC_INT ((uint)0x00000000)
#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
#define CPM_BRG_ATB ((uint)0x00002000)
#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
#define CPM_BRG_DIV16 ((uint)0x00000001)
/* SI Clock Route Register
*/
#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000)
#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000)
#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800)
#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100)
#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000)
#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000)
#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000)
#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000)
/* SCCs.
*/
#define SCC_GSMRH_IRP ((uint)0x00040000)
#define SCC_GSMRH_GDE ((uint)0x00010000)
#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
#define SCC_GSMRH_REVD ((uint)0x00002000)
#define SCC_GSMRH_TRX ((uint)0x00001000)
#define SCC_GSMRH_TTX ((uint)0x00000800)
#define SCC_GSMRH_CDP ((uint)0x00000400)
#define SCC_GSMRH_CTSP ((uint)0x00000200)
#define SCC_GSMRH_CDS ((uint)0x00000100)
#define SCC_GSMRH_CTSS ((uint)0x00000080)
#define SCC_GSMRH_TFL ((uint)0x00000040)
#define SCC_GSMRH_RFW ((uint)0x00000020)
#define SCC_GSMRH_TXSY ((uint)0x00000010)
#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
#define SCC_GSMRH_RTSM ((uint)0x00000002)
#define SCC_GSMRH_RSYN ((uint)0x00000001)
#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
#define SCC_GSMRL_TCI ((uint)0x10000000)
#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
#define SCC_GSMRL_RINV ((uint)0x02000000)
#define SCC_GSMRL_TINV ((uint)0x01000000)
#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
#define SCC_GSMRL_TEND ((uint)0x00040000)
#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
#define SCC_GSMRL_ENR ((uint)0x00000020)
#define SCC_GSMRL_ENT ((uint)0x00000010)
#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
#define SCC_TODR_TOD ((ushort)0x8000)
/* SCC Event and Mask register.
*/
#define SCCM_TXE ((unsigned char)0x10)
#define SCCM_BSY ((unsigned char)0x04)
#define SCCM_TX ((unsigned char)0x02)
#define SCCM_RX ((unsigned char)0x01)
typedef struct scc_param {
ushort scc_rbase; /* Rx Buffer descriptor base address */
ushort scc_tbase; /* Tx Buffer descriptor base address */
u_char scc_rfcr; /* Rx function code */
u_char scc_tfcr; /* Tx function code */
ushort scc_mrblr; /* Max receive buffer length */
uint scc_rstate; /* Internal */
uint scc_idp; /* Internal */
ushort scc_rbptr; /* Internal */
ushort scc_ibc; /* Internal */
uint scc_rxtmp; /* Internal */
uint scc_tstate; /* Internal */
uint scc_tdp; /* Internal */
ushort scc_tbptr; /* Internal */
ushort scc_tbc; /* Internal */
uint scc_txtmp; /* Internal */
uint scc_rcrc; /* Internal */
uint scc_tcrc; /* Internal */
} sccp_t;
/* Function code bits.
*/
#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
/* CPM Ethernet through SCCx.
*/
typedef struct scc_enet {
sccp_t sen_genscc;
uint sen_cpres; /* Preset CRC */
uint sen_cmask; /* Constant mask for CRC */
uint sen_crcec; /* CRC Error counter */
uint sen_alec; /* alignment error counter */
uint sen_disfc; /* discard frame counter */
ushort sen_pads; /* Tx short frame pad character */
ushort sen_retlim; /* Retry limit threshold */
ushort sen_retcnt; /* Retry limit counter */
ushort sen_maxflr; /* maximum frame length register */
ushort sen_minflr; /* minimum frame length register */
ushort sen_maxd1; /* maximum DMA1 length */
ushort sen_maxd2; /* maximum DMA2 length */
ushort sen_maxd; /* Rx max DMA */
ushort sen_dmacnt; /* Rx DMA counter */
ushort sen_maxb; /* Max BD byte count */
ushort sen_gaddr1; /* Group address filter */
ushort sen_gaddr2;
ushort sen_gaddr3;
ushort sen_gaddr4;
uint sen_tbuf0data0; /* Save area 0 - current frame */
uint sen_tbuf0data1; /* Save area 1 - current frame */
uint sen_tbuf0rba; /* Internal */
uint sen_tbuf0crc; /* Internal */
ushort sen_tbuf0bcnt; /* Internal */
ushort sen_paddrh; /* physical address (MSB) */
ushort sen_paddrm;
ushort sen_paddrl; /* physical address (LSB) */
ushort sen_pper; /* persistence */
ushort sen_rfbdptr; /* Rx first BD pointer */
ushort sen_tfbdptr; /* Tx first BD pointer */
ushort sen_tlbdptr; /* Tx last BD pointer */
uint sen_tbuf1data0; /* Save area 0 - current frame */
uint sen_tbuf1data1; /* Save area 1 - current frame */
uint sen_tbuf1rba; /* Internal */
uint sen_tbuf1crc; /* Internal */
ushort sen_tbuf1bcnt; /* Internal */
ushort sen_txlen; /* Tx Frame length counter */
ushort sen_iaddr1; /* Individual address filter */
ushort sen_iaddr2;
ushort sen_iaddr3;
ushort sen_iaddr4;
ushort sen_boffcnt; /* Backoff counter */
/* NOTE: Some versions of the manual have the following items
* incorrectly documented. Below is the proper order.
*/
ushort sen_taddrh; /* temp address (MSB) */
ushort sen_taddrm;
ushort sen_taddrl; /* temp address (LSB) */
} scc_enet_t;
/**********************************************************************
*
* Board specific configuration settings.
*
* Please note that we use the presence of a #define SCC_ENET and/or
* #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
**********************************************************************/
/*** ADS *************************************************************/
#if defined(CONFIG_MPC860) && defined(CONFIG_ADS)
/* This ENET stuff is for the MPC860ADS with ethernet on SCC1.
*/
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001)
#define PA_ENET_TXD ((ushort)0x0002)
#define PA_ENET_TCLK ((ushort)0x0100)
#define PA_ENET_RCLK ((ushort)0x0200)
#define PB_ENET_TENA ((uint)0x00001000)
#define PC_ENET_CLSN ((ushort)0x0010)
#define PC_ENET_RENA ((ushort)0x0020)
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000002c)
/* 68160 PHY control */
#define PC_ENET_ETHLOOP ((ushort)0x0800)
#define PC_ENET_TPFLDL ((ushort)0x0400)
#define PC_ENET_TPSQEL ((ushort)0x0200)
#endif /* MPC860ADS */
/*** BSEIP **********************************************************/
#ifdef CONFIG_BSEIP
/* This ENET stuff is for the MPC823 with ethernet on SCC2.
* This is unique to the BSE ip-Engine board.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0100)
#define PA_ENET_RCLK ((ushort)0x0200)
#define PB_ENET_TENA ((uint)0x00002000)
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
/* BSE uses port B and C bits for PHY control also.
*/
#define PB_BSE_POWERUP ((uint)0x00000004)
#define PB_BSE_FDXDIS ((uint)0x00008000)
#define PC_BSE_LOOPBACK ((ushort)0x0800)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002c00)
#endif /* CONFIG_BSEIP */
/*** BSEIP **********************************************************/
#ifdef CONFIG_FLAGADM
/* Enet configuration for the FLAGADM */
/* Enet on SCC2 */
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0100)
#define PA_ENET_RCLK ((ushort)0x0400)
#define PB_ENET_TENA ((uint)0x00002000)
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00003400)
#endif /* CONFIG_FLAGADM */
/*** ELPT860 *********************************************************/
#ifdef CONFIG_ELPT860
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
*/
# define PROFF_ENET PROFF_SCC1
# define CPM_CR_ENET CPM_CR_CH_SCC1
# define SCC_ENET 0
# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */
# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to
* SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
*/
# define SICR_ENET_MASK ((uint)0x000000FF)
# define SICR_ENET_CLKRT ((uint)0x00000025)
#endif /* CONFIG_ELPT860 */
/*** ESTEEM 192E **************************************************/
#ifdef CONFIG_ESTEEM192E
/* ESTEEM192E
* This ENET stuff is for the MPC850 with ethernet on SCC2. This
* is very similar to the RPX-Lite configuration.
* Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0200)
#define PA_ENET_RCLK ((ushort)0x0800)
#define PB_ENET_TENA ((uint)0x00002000)
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00003d00)
#define PB_ENET_LOOPBACK ((uint)0x00004000)
#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
#endif
/*** FADS823 ********************************************************/
#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS)
/* This ENET stuff is for the MPC823FADS with ethernet on SCC2.
*/
#ifdef CONFIG_SCC2_ENET
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define CPMVEC_ENET CPMVEC_SCC2
#endif
#ifdef CONFIG_SCC1_ENET
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define CPMVEC_ENET CPMVEC_SCC1
#endif
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0400)
#define PA_ENET_RCLK ((ushort)0x0200)
#define PB_ENET_TENA ((uint)0x00002000)
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002e00)
#endif /* CONFIG_FADS823FADS */
/*** FADS850SAR ********************************************************/
#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS)
/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of
* this may be unique to the FADS850SAR configuration.
* Note TENA is on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */
#endif /* CONFIG_FADS850SAR */
/*** FADS860T********************************************************/
#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
/*
* This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1.
*/
#ifdef CONFIG_SCC1_ENET
#define SCC_ENET 0
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define PA_ENET_RXD ((ushort)0x0001)
#define PA_ENET_TXD ((ushort)0x0002)
#define PA_ENET_TCLK ((ushort)0x0100)
#define PA_ENET_RCLK ((ushort)0x0200)
#define PB_ENET_TENA ((uint)0x00001000)
#define PC_ENET_CLSN ((ushort)0x0010)
#define PC_ENET_RENA ((ushort)0x0020)
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000002c)
#endif /* CONFIG_SCC1_ETHERNET */
/*
* This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS
* with ethernet on FEC.
*/
#ifdef CONFIG_FEC_ENET
#define FEC_ENET /* Use FEC for Ethernet */
#endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_FADS && CONFIG_MPC86x */
/*** FPS850L, FPS860L ************************************************/
#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002600)
#endif /* CONFIG_FPS850L, CONFIG_FPS860L */
/*** GEN860T **********************************************************/
#if defined(CONFIG_GEN860T)
#undef SCC_ENET
#define FEC_ENET
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */
#endif /* CONFIG_GEN860T */
/*** GENIETV ********************************************************/
#if defined(CONFIG_GENIETV)
/* Ethernet is only on SCC2 */
#define CONFIG_SCC2_ENET
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define CPMVEC_ENET CPMVEC_SCC2
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002e00)
#endif /* CONFIG_GENIETV */
/*** HERMES-PRO ******************************************************/
/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
#ifdef CONFIG_HERMES
#define FEC_ENET /* use FEC for EThernet */
#undef SCC_ENET
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
#endif /* CONFIG_HERMES */
/*** ICU862 **********************************************************/
#if defined(CONFIG_ICU862)
#ifdef CONFIG_FEC_ENET
#define FEC_ENET /* use FEC for EThernet */
#endif /* CONFIG_FEC_ETHERNET */
#endif /* CONFIG_ICU862 */
/*** IP860 **********************************************************/
#if defined(CONFIG_IP860)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
*/
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
* SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
*/
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000002C)
#endif /* CONFIG_IP860 */
/*** IVMS8 **********************************************************/
/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
#define FEC_ENET /* use FEC for EThernet */
#undef SCC_ENET
#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
/*** KUP4K, KUP4X ****************************************************/
/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */
#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
#define FEC_ENET /* use FEC for EThernet */
#undef SCC_ENET
#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
#endif /* CONFIG_KUP4K */
/*** LWMON **********************************************************/
#if defined(CONFIG_LWMON)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00003E00)
#endif /* CONFIG_LWMON */
/*** NX823 ***********************************************/
#if defined(CONFIG_NX823)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002f00)
#endif /* CONFIG_NX823 */
/*** MBX ************************************************************/
#ifdef CONFIG_MBX
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use. The TCLK and RCLK seem unique
* to the MBX860 board. Any two of the four available clocks could be
* used, and the MPC860 cookbook manual has an example using different
* clock pins.
*/
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001)
#define PA_ENET_TXD ((ushort)0x0002)
#define PA_ENET_TCLK ((ushort)0x0200)
#define PA_ENET_RCLK ((ushort)0x0800)
#define PC_ENET_TENA ((ushort)0x0001)
#define PC_ENET_CLSN ((ushort)0x0010)
#define PC_ENET_RENA ((ushort)0x0020)
/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
* SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
*/
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000003d)
#endif /* CONFIG_MBX */
/*** KM8XX *********************************************************/
/* The KM8XX Service Module uses SCC3 for Ethernet */
#ifdef CONFIG_KM8XX
#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
#define CPM_CR_ENET CPM_CR_CH_SCC3
#define SCC_ENET 2
#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
* SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
*/
#define SICR_ENET_MASK ((uint)0x00FF0000)
#define SICR_ENET_CLKRT ((uint)0x00250000)
#endif /* CONFIG_KM8XX */
/*** MHPC ********************************************************/
#if defined(CONFIG_MHPC)
/* This ENET stuff is for the MHPC with ethernet on SCC2.
* Note TENA is on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
#endif /* CONFIG_MHPC */
/*** NETVIA *******************************************************/
/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
#if ( defined CONFIG_SVM_SC8xx )
# ifndef CONFIG_FEC_ENET
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
/* Bits in parallel I/O port registers that have to be set/cleared
* * * * to configure the pins for SCC2 use.
* * * */
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
* * * */
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00003700)
# else /* Use FEC for Fast Ethernet */
#undef SCC_ENET
#define FEC_ENET
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
# endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_SVM_SC8xx */
#if defined(CONFIG_NETVIA)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
#elif CONFIG_NETVIA_VERSION >= 2
# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
#endif
#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002f00)
#endif /* CONFIG_NETVIA */
/*** QS850/QS823 ***************************************************/
#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
#undef FEC_ENET /* Don't use FEC for EThernet */
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
/* SCC2 TXCLK from CLK2
* SCC2 RXCLK from CLK4
* SCC2 Connected to NMSI */
#define SICR_ENET_MASK ((uint)0x00007F00)
#define SICR_ENET_CLKRT ((uint)0x00003D00)
#endif /* CONFIG_QS850/QS823 */
/*** QS860T ***************************************************/
#ifdef CONFIG_QS860T
#ifdef CONFIG_FEC_ENET
#define FEC_ENET /* use FEC for EThernet */
#endif /* CONFIG_FEC_ETHERNET */
/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
#define SICR_ENET_MASK ((uint)0x000000ff)
/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
#define SICR_ENET_CLKRT ((uint)0x0000003D)
#endif /* CONFIG_QS860T */
/*** RPXCLASSIC *****************************************************/
#ifdef CONFIG_RPXCLASSIC
#ifdef CONFIG_FEC_ENET
# define FEC_ENET /* use FEC for EThernet */
# undef SCC_ENET
#else /* ! CONFIG_FEC_ENET */
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
*/
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001)
#define PA_ENET_TXD ((ushort)0x0002)
#define PA_ENET_TCLK ((ushort)0x0200)
#define PA_ENET_RCLK ((ushort)0x0800)
#define PB_ENET_TENA ((uint)0x00001000)
#define PC_ENET_CLSN ((ushort)0x0010)
#define PC_ENET_RENA ((ushort)0x0020)
/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
* SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
*/
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x0000003d)
#endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_RPXCLASSIC */
/*** RPXLITE ********************************************************/
#ifdef CONFIG_RPXLITE
/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
* this may be unique to the RPX-Lite configuration.
* Note TENA is on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0200)
#define PA_ENET_RCLK ((ushort)0x0800)
#if defined(CONFIG_RMU)
#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */
#else
#define PB_ENET_TENA ((uint)0x00002000)
#endif
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00003d00)
#endif /* CONFIG_RPXLITE */
/*** SM850 *********************************************************/
/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
#ifdef CONFIG_SM850
#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
#define CPM_CR_ENET CPM_CR_CH_SCC3
#define SCC_ENET 2
#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
*/
#define SICR_ENET_MASK ((uint)0x00FF0000)
#define SICR_ENET_CLKRT ((uint)0x00260000)
#endif /* CONFIG_SM850 */
/*** SPD823TS ******************************************************/
#ifdef CONFIG_SPD823TS
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002E00)
#endif /* CONFIG_SPD823TS */
/*** SXNI855T ******************************************************/
#if defined(CONFIG_SXNI855T)
#ifdef CONFIG_FEC_ENET
#define FEC_ENET /* use FEC for Ethernet */
#endif /* CONFIG_FEC_ETHERNET */
#endif /* CONFIG_SXNI855T */
/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */
#define SCC_ENET 1
#endif
#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
#if defined(CONFIG_R360MPI)
#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
#endif /* CONFIG_R360MPI */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002600)
# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
#define FEC_ENET
# endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
*/
#define PROFF_ENET PROFF_SCC1
#define CPM_CR_ENET CPM_CR_CH_SCC1
#define SCC_ENET 0
#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
*/
#define SICR_ENET_MASK ((uint)0x000000ff)
#define SICR_ENET_CLKRT ((uint)0x00000026)
# endif /* CONFIG_SCC1_ENET */
# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
#define FEC_ENET
#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
# endif /* CONFIG_FEC_ENET */
#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
/*** V37 **********************************************************/
#ifdef CONFIG_V37
/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of
* this may be unique to the Marel V37 configuration.
* Note TENA is on Port B.
*/
#define PROFF_ENET PROFF_SCC2
#define CPM_CR_ENET CPM_CR_CH_SCC2
#define SCC_ENET 1
#define PA_ENET_RXD ((ushort)0x0004)
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0400)
#define PA_ENET_RCLK ((ushort)0x0200)
#define PB_ENET_TENA ((uint)0x00002000)
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002e00)
#endif /* CONFIG_V37 */
/*********************************************************************/
/* SCC Event register as used by Ethernet.
*/
#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
/* SCC Mode Register (PSMR) as used by Ethernet.
*/
#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
/* Buffer descriptor control/status used by Ethernet receive.
*/
#define BD_ENET_RX_EMPTY ((ushort)0x8000)
#define BD_ENET_RX_WRAP ((ushort)0x2000)
#define BD_ENET_RX_INTR ((ushort)0x1000)
#define BD_ENET_RX_LAST ((ushort)0x0800)
#define BD_ENET_RX_FIRST ((ushort)0x0400)
#define BD_ENET_RX_MISS ((ushort)0x0100)
#define BD_ENET_RX_LG ((ushort)0x0020)
#define BD_ENET_RX_NO ((ushort)0x0010)
#define BD_ENET_RX_SH ((ushort)0x0008)
#define BD_ENET_RX_CR ((ushort)0x0004)
#define BD_ENET_RX_OV ((ushort)0x0002)
#define BD_ENET_RX_CL ((ushort)0x0001)
#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
/* Buffer descriptor control/status used by Ethernet transmit.
*/
#define BD_ENET_TX_READY ((ushort)0x8000)
#define BD_ENET_TX_PAD ((ushort)0x4000)
#define BD_ENET_TX_WRAP ((ushort)0x2000)
#define BD_ENET_TX_INTR ((ushort)0x1000)
#define BD_ENET_TX_LAST ((ushort)0x0800)
#define BD_ENET_TX_TC ((ushort)0x0400)
#define BD_ENET_TX_DEF ((ushort)0x0200)
#define BD_ENET_TX_HB ((ushort)0x0100)
#define BD_ENET_TX_LC ((ushort)0x0080)
#define BD_ENET_TX_RL ((ushort)0x0040)
#define BD_ENET_TX_RCMASK ((ushort)0x003c)
#define BD_ENET_TX_UN ((ushort)0x0002)
#define BD_ENET_TX_CSL ((ushort)0x0001)
#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
/* SCC as UART
*/
typedef struct scc_uart {
sccp_t scc_genscc;
uint scc_res1; /* Reserved */
uint scc_res2; /* Reserved */
ushort scc_maxidl; /* Maximum idle chars */
ushort scc_idlc; /* temp idle counter */
ushort scc_brkcr; /* Break count register */
ushort scc_parec; /* receive parity error counter */
ushort scc_frmec; /* receive framing error counter */
ushort scc_nosec; /* receive noise counter */
ushort scc_brkec; /* receive break condition counter */
ushort scc_brkln; /* last received break length */
ushort scc_uaddr1; /* UART address character 1 */
ushort scc_uaddr2; /* UART address character 2 */
ushort scc_rtemp; /* Temp storage */
ushort scc_toseq; /* Transmit out of sequence char */
ushort scc_char1; /* control character 1 */
ushort scc_char2; /* control character 2 */
ushort scc_char3; /* control character 3 */
ushort scc_char4; /* control character 4 */
ushort scc_char5; /* control character 5 */
ushort scc_char6; /* control character 6 */
ushort scc_char7; /* control character 7 */
ushort scc_char8; /* control character 8 */
ushort scc_rccm; /* receive control character mask */
ushort scc_rccr; /* receive control character register */
ushort scc_rlbc; /* receive last break character */
} scc_uart_t;
/* SCC Event and Mask registers when it is used as a UART.
*/
#define UART_SCCM_GLR ((ushort)0x1000)
#define UART_SCCM_GLT ((ushort)0x0800)
#define UART_SCCM_AB ((ushort)0x0200)
#define UART_SCCM_IDL ((ushort)0x0100)
#define UART_SCCM_GRA ((ushort)0x0080)
#define UART_SCCM_BRKE ((ushort)0x0040)
#define UART_SCCM_BRKS ((ushort)0x0020)
#define UART_SCCM_CCR ((ushort)0x0008)
#define UART_SCCM_BSY ((ushort)0x0004)
#define UART_SCCM_TX ((ushort)0x0002)
#define UART_SCCM_RX ((ushort)0x0001)
/* The SCC PSMR when used as a UART.
*/
#define SCU_PSMR_FLC ((ushort)0x8000)
#define SCU_PSMR_SL ((ushort)0x4000)
#define SCU_PSMR_CL ((ushort)0x3000)
#define SCU_PSMR_UM ((ushort)0x0c00)
#define SCU_PSMR_FRZ ((ushort)0x0200)
#define SCU_PSMR_RZS ((ushort)0x0100)
#define SCU_PSMR_SYN ((ushort)0x0080)
#define SCU_PSMR_DRT ((ushort)0x0040)
#define SCU_PSMR_PEN ((ushort)0x0010)
#define SCU_PSMR_RPM ((ushort)0x000c)
#define SCU_PSMR_REVP ((ushort)0x0008)
#define SCU_PSMR_TPM ((ushort)0x0003)
#define SCU_PSMR_TEVP ((ushort)0x0003)
/* CPM Transparent mode SCC.
*/
typedef struct scc_trans {
sccp_t st_genscc;
uint st_cpres; /* Preset CRC */
uint st_cmask; /* Constant mask for CRC */
} scc_trans_t;
#define BD_SCC_TX_LAST ((ushort)0x0800)
/* IIC parameter RAM.
*/
typedef struct iic {
ushort iic_rbase; /* Rx Buffer descriptor base address */
ushort iic_tbase; /* Tx Buffer descriptor base address */
u_char iic_rfcr; /* Rx function code */
u_char iic_tfcr; /* Tx function code */
ushort iic_mrblr; /* Max receive buffer length */
uint iic_rstate; /* Internal */
uint iic_rdp; /* Internal */
ushort iic_rbptr; /* Internal */
ushort iic_rbc; /* Internal */
uint iic_rxtmp; /* Internal */
uint iic_tstate; /* Internal */
uint iic_tdp; /* Internal */
ushort iic_tbptr; /* Internal */
ushort iic_tbc; /* Internal */
uint iic_txtmp; /* Internal */
uint iic_res; /* reserved */
ushort iic_rpbase; /* Relocation pointer */
ushort iic_res2; /* reserved */
} iic_t;
/* SPI parameter RAM.
*/
typedef struct spi {
ushort spi_rbase; /* Rx Buffer descriptor base address */
ushort spi_tbase; /* Tx Buffer descriptor base address */
u_char spi_rfcr; /* Rx function code */
u_char spi_tfcr; /* Tx function code */
ushort spi_mrblr; /* Max receive buffer length */
uint spi_rstate; /* Internal */
uint spi_rdp; /* Internal */
ushort spi_rbptr; /* Internal */
ushort spi_rbc; /* Internal */
uint spi_rxtmp; /* Internal */
uint spi_tstate; /* Internal */
uint spi_tdp; /* Internal */
ushort spi_tbptr; /* Internal */
ushort spi_tbc; /* Internal */
uint spi_txtmp; /* Internal */
uint spi_res;
ushort spi_rpbase; /* Relocation pointer */
ushort spi_res2;
} spi_t;
/* SPI Mode register.
*/
#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
#define SPMODE_EN ((ushort)0x0100) /* Enable */
#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
#define SPMODE_PM(x) ((x) &0xF)
/* HDLC parameter RAM.
*/
typedef struct hdlc_pram_s {
/*
* SCC parameter RAM
*/
ushort rbase; /* Rx Buffer descriptor base address */
ushort tbase; /* Tx Buffer descriptor base address */
uchar rfcr; /* Rx function code */
uchar tfcr; /* Tx function code */
ushort mrblr; /* Rx buffer length */
ulong rstate; /* Rx internal state */
ulong rptr; /* Rx internal data pointer */
ushort rbptr; /* rb BD Pointer */
ushort rcount; /* Rx internal byte count */
ulong rtemp; /* Rx temp */
ulong tstate; /* Tx internal state */
ulong tptr; /* Tx internal data pointer */
ushort tbptr; /* Tx BD pointer */
ushort tcount; /* Tx byte count */
ulong ttemp; /* Tx temp */
ulong rcrc; /* temp receive CRC */
ulong tcrc; /* temp transmit CRC */
/*
* HDLC specific parameter RAM
*/
uchar res[4]; /* reserved */
ulong c_mask; /* CRC constant */
ulong c_pres; /* CRC preset */
ushort disfc; /* discarded frame counter */
ushort crcec; /* CRC error counter */
ushort abtsc; /* abort sequence counter */
ushort nmarc; /* nonmatching address rx cnt */
ushort retrc; /* frame retransmission cnt */
ushort mflr; /* maximum frame length reg */
ushort max_cnt; /* maximum length counter */
ushort rfthr; /* received frames threshold */
ushort rfcnt; /* received frames count */
ushort hmask; /* user defined frm addr mask */
ushort haddr1; /* user defined frm address 1 */
ushort haddr2; /* user defined frm address 2 */
ushort haddr3; /* user defined frm address 3 */
ushort haddr4; /* user defined frm address 4 */
ushort tmp; /* temp */
ushort tmp_mb; /* temp */
} hdlc_pram_t;
/* CPM interrupts. There are nearly 32 interrupts generated by CPM
* channels or devices. All of these are presented to the PPC core
* as a single interrupt. The CPM interrupt handler dispatches its
* own handlers, in a similar fashion to the PPC core handler. We
* use the table as defined in the manuals (i.e. no special high
* priority and SCC1 == SCCa, etc...).
*/
#define CPMVEC_NR 32
#define CPMVEC_OFFSET 0x00010000
#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET)
#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET)
#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET)
#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET)
#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET)
#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET)
#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET)
#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET)
#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET)
#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET)
#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET)
#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET)
#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET)
#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET)
#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET)
#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET)
#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET)
#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
/* CPM interrupt configuration vector.
*/
#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
#define CICR_IEN ((uint)0x00000080) /* Int. enable */
#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
#endif /* __CPM_8XX__ */
Reference in a new issue View git blame Copy permalink