mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-04 18:41:03 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
154 lines
3.9 KiB
C
154 lines
3.9 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Bluewater Systems Snapper 9260/9G20 modules
|
|
*
|
|
* (C) Copyright 2011 Bluewater Systems
|
|
* Author: Andre Renaud <andre@bluewatersys.com>
|
|
* Author: Ryan Mallon <ryan@bluewatersys.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <init.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/arch/at91sam9260_matrix.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/atmel_serial.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <i2c.h>
|
|
#include <pca953x.h>
|
|
#include <linux/delay.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* IO Expander pins */
|
|
#define IO_EXP_ETH_RESET (0 << 1)
|
|
#define IO_EXP_ETH_POWER (1 << 1)
|
|
|
|
static void macb_hw_init(void)
|
|
{
|
|
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
|
|
|
|
at91_periph_clk_enable(ATMEL_ID_EMAC0);
|
|
|
|
/* Disable pull-ups to prevent PHY going into test mode */
|
|
writel(pin_to_mask(AT91_PIN_PA14) |
|
|
pin_to_mask(AT91_PIN_PA15) |
|
|
pin_to_mask(AT91_PIN_PA18),
|
|
&pioa->pudr);
|
|
|
|
/* Power down ethernet */
|
|
pca953x_set_dir(0x28, IO_EXP_ETH_POWER, PCA953X_DIR_OUT);
|
|
pca953x_set_val(0x28, IO_EXP_ETH_POWER, 1);
|
|
|
|
/* Hold ethernet in reset */
|
|
pca953x_set_dir(0x28, IO_EXP_ETH_RESET, PCA953X_DIR_OUT);
|
|
pca953x_set_val(0x28, IO_EXP_ETH_RESET, 0);
|
|
|
|
/* Enable ethernet power */
|
|
pca953x_set_val(0x28, IO_EXP_ETH_POWER, 0);
|
|
|
|
at91_phy_reset();
|
|
|
|
/* Bring the ethernet out of reset */
|
|
pca953x_set_val(0x28, IO_EXP_ETH_RESET, 1);
|
|
|
|
/* The phy internal reset take 21ms */
|
|
udelay(21 * 1000);
|
|
|
|
/* Re-enable pull-up */
|
|
writel(pin_to_mask(AT91_PIN_PA14) |
|
|
pin_to_mask(AT91_PIN_PA15) |
|
|
pin_to_mask(AT91_PIN_PA18),
|
|
&pioa->puer);
|
|
|
|
at91_macb_hw_init();
|
|
}
|
|
|
|
static void nand_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
|
|
unsigned long csa;
|
|
|
|
/* Enable CS3 as NAND/SmartMedia */
|
|
csa = readl(&matrix->ebicsa);
|
|
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
|
|
writel(csa, &matrix->ebicsa);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
|
|
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
|
|
&smc->cs[3].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_DBW_8 |
|
|
AT91_SMC_MODE_TDF_CYCLE(3),
|
|
&smc->cs[3].mode);
|
|
|
|
/* Configure RDY/BSY */
|
|
gpio_request(CONFIG_SYS_NAND_READY_PIN, "nand_rdy");
|
|
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
|
|
|
|
/* Enable NandFlash */
|
|
gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "nand_ce");
|
|
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_PIOA);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOB);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOC);
|
|
|
|
/* The mach-type is the same for both Snapper 9260 and 9G20 */
|
|
gd->bd->bi_arch_number = MACH_TYPE_SNAPPER_9260;
|
|
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
/* Initialise peripherals */
|
|
at91_seriald_hw_init();
|
|
i2c_set_bus_num(0);
|
|
nand_hw_init();
|
|
macb_hw_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x1f);
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
return 0;
|
|
}
|
|
|
|
void reset_phy(void)
|
|
{
|
|
}
|
|
|
|
static struct atmel_serial_plat at91sam9260_serial_plat = {
|
|
.base_addr = ATMEL_BASE_DBGU,
|
|
};
|
|
|
|
U_BOOT_DRVINFO(at91sam9260_serial) = {
|
|
.name = "serial_atmel",
|
|
.plat = &at91sam9260_serial_plat,
|
|
};
|